Even though the trunnion mechanism from Powermatic has been known to be the best there is, further refinements have been made to it in order to make it even better. The conically shaped worm gear drive with better surface area, the high end bearings, but also the cast iron, box style construction combine with the solid and smooth feel of the height and tilt adjustments. Thanks to the adjustable backlash, it’s very easy for users to adjust the mechanism back to the factory fresh feel and clearances.
With this saw, it was a very easy thing to plug it on and get started. The included cord is a reasonable length, but you’ll still need an extension cord unless you happen to be right next to an outlet in your workshop. Raising and lowering the blade is a smooth process and we found the mechanism to be nice and stiff, so you can be very precise with your cut depth. Only time will reveal whether or not this stays tight over the long haul, but it seems to be well-made. Mounting the accessories, like the smart guard system is quick. You just raise the riving knife using the release lever. The riving knife locks into a lower and upper position through the use of two sets of pins. In the upper position it is ready to accept the barrier guard, which you can remove from below the saw. It attaches easily with a lever lock and the anti-kickback device can then be placed on the back of the riving knife such that the teeth are set to grab any wood brought forward by the blade. The physical nature of the barrier guard assembly precludes you from placing your fingers anywhere near the cutting surface of the blade. We (and Bosch) recommend keeping this guard on the saw anytime you are doing “through” cuts. All-in-all, the table saw’s included safety features are more than adequate to keep you from encountering any unfortunate accidents. Removing them, or using the tool improperly, however, will considerably raise your level of risk.
The service coverage under the warranty requires you to either bring the machine to an authorized dealer or ship it back to the company on your dollar. That’s a major downside, and it’s one reason we’re recommending purchasing add-on warranty coverage for this one. If you’re dealing with a third party provider, you can simply get a replacement without having to go through frustrating company reps.
It’s powerful. The blade is hooked up to a 3HP motor which can muster a no-load speed up to 4000 RPM! That’s perfect for all your cutting needs, and it’s much better than other inexpensive units when it comes to slicing hardwoods or thicker stock. While many smaller units advertise similar HP ratings, this one actually lives up to the promise, since it uses 220V power.
The accuracy and safety of any given saw is dependent upon the blade being parallel to the rip fence. Since we tested the amount of difference in parallelism between the saw blade and the miter slot in the previous test, we need only to see if the miter slot is parallel to the rip fence to see if the saw has a parallel relationship between the blade and the rip fence.
Rockwell is the “freshman” brand among the other longer-standing benchtop power tool companies represented here, and its table saw revealed some “first rodeo” shortcomings. While the motor was amply powerful for my cutting tests, the blade arbor assembly was 1/16″ out of parallel with the miter slots. It’s a condition called “heeling” without easy adjustment in the manual. So, for my testing purposes I had to set the rip fence askew in order to align it parallel to the blade. The problem would need to be addressed on this sample saw for long-term use.

But if you have the space for the DeWalt to sit upright at a work station or deep storage shelf, then it may be the better choice, thanks to its more comfortable adjustment controls. You won't be able to use a dado blade with the DeWalt (at least not safely), and the rip capacity is slightly smaller, but there's a reason why it's been popular for a while now. It's a great saw that delivers reliable performance.
Both saws were almost equally quick to setup for use, with the DeWalt coming out slightly ahead. The throat plate, which is thicker and sturdier than Bosch's, is slightly easier to remove and reinsert. The DeWalt's blade cavity offers greater clearance, which makes locking down and loosening the riving knife easier without scraping a knuckle. Dewalt's riving knife adjustment required less wiggling and hunting to get it set properly.

Setting up or taking down Craftsman’s spring-assisted stand is a six-step process, involving various release latches. It’s not intuitive like that of Bosch or RIDGID. And, once the stand is folded down, don’t lift the handles up too far when rolling the saw around, or the stand drags against the floor. A shorter woodworker might find this less of a problem than this 6′ 3″ tester did. I also found that the stand’s narrow stance and light weight couldn’t prevent it from skittering on the floor as I pushed heavy lumber across the top. A word to the wise: weigh the base down for heavy-duty work or for cutting large sheet goods.
A table saw can be classified in many ways, and I’ve come across terms like contractor, folding, featherboard, hobby, induction, sliding and zero clearance. However, I will conform to the most basic and clear classification and range the tables accordingly. That means I’ll order them by benchtop table saws, jobsite table saws, cabinet saws and hybrid table saws.
We hear the term accuracy tossed around when it comes to finding the best portable jobsite table saw, but we really have to narrow down what that means. Every saw we tested has the capability of being calibrated and it should be the first thing you do after setting it up. Like a new miter saw, blade calibration is simply part of delivering professional results.
We cannot emphasize enough how important it is to think about safety at all times while using these tools. Even the slightest mistake can make a difference between life and death. The worst part is the fact that it usually happens in an instant, leaving you no time to react at all. Therefore, whatever you do, don’t forget that there’s a thin line between you having ten fingers at one moment and 8 in the next second.
To adjust blade height you simply operate the elevation wheel located on the front of the saw, and the angle of the blade can be set through a switch which is behind the wheel in case you want to make bevel cuts. The angle can be set anywhere between 0 and 45 degrees, and once you’ve adjusted the bevel angle it can be locked into place using the handle.
The Bosch 4100-09 offers many advanced features, making it a very capable table saw for woodworking. The air-filled wheels and gravity rising stand makes this table saw functional and lightweight. Set up and tear down of the table saw is a breeze. This technology allows the table saw to be moved from place to place, even over the most rough and challenging areas of the work site. The 4100-09 weighs 39 pounds, making it the perfect portable table saw. Although it is lightweight, it is very durable and stable.
Because we’re passionate woodworkers who care deeply about the quality of the tools we work with, we have a tendency to recommend that even the most budget-conscious buyer spend a little more to get something high-quality. However, we know that some DIYers might have the ambition to take their woodworking to the next level with a table saw, but might not necessarily have the funds.
And finally, they all include a blade guard that can be removed and reinstalled without tools. Because a few sawing operations, such as non-through cuts, require you to remove the blade guard, we like saws that make this task easy. The Bosch, DeWalt and Ridgid saws have well-designed blade guards that are easy to remove and reinstall. The blade guards on all but the Porter-Cable and Craftsman also have a feature that holds the blade guard in the raised position to allow better blade visibility for setting up cuts.

The blade is a 24 tooth carbide tipped blade that is durable and long lasting. You can even adjust it to a 45 degree angle for those more difficult bevel cuts. If you’re working on uneven ground, you’ll love the rear feet that are fully adjustable so you can level you work space. You’ll get a lot of use out of the onboard storage that will give you easy access to the push stick and guarding components. Weighing only 45 pounds, you can move the table saw from work site to home with ease.

You can store and transport the Bosch upright or on either of its sides. In between our tests, we found that the saw neatly stored away on its side on a workbench shelf. On the other hand, the DeWalt can only be stored or transported in its upright position. While it may possible to rest the saw briefly on one of its sides, there is the potential to damage the power cord, plug, or the ends of the telescoping fence rails. 

A table saw is the centerpiece of any home workshop, and it’s often the very first power tool to be cranked up at the start of any woodworking task. They’re essential for the necessary task of sizing wood for each project – whether narrowing the width of boards, cutting plywood sheets, or tackling specialized cuts like grooves, slots, and tenons. Because of their important role in DIY and professional construction, choosing the right table saw is critically important. At BestReviews, we’ve researched table saws in depth. We’re here to help you decide which type of table saw will best meet your needs.
Which leads to a problem. A standard blade should not have that kind of space around it. Fortunately, Bosch sell very inexpensive throat plate blanks that can become zero clearance inserts. I have one for each of my three main blades and a fourth unused one that I put aside just in case. While I can make my own, it just isn’t worth the hassle as these are pretty affordable.

If you’re looking for the best table saw out there, then there’s no better choice than the Powermatic 1792001K PM2000. This is an amazing cabinet table saw that features a 1-phase, 3 HP motor with rout-R lift and Accu-fence system which set a new standard for innovation through thanks to the saw’s large body design and an incredible range of patented features. Almost each feature of the 1792001K PM2000 sets a new standard by which every other cabinet table saw on the market is judged, so you can have the peace of mind that this is not your regular cabinet table saw.


We were impressed with the Bosch Glide Miter Saw which was revealed in 2010 and revolutionized the depth required by a saw in close quarters. Building on their solution-based approach to products, the company has finally addressed the need for a truly portable full-power jobsite table saw. The Bosch GTS1031 table saw can be carried by its single handle, which is balanced in the middle, and all accessories are safely and securely stored on-board. This was demonstrated wonderfully by none other than Jason Feldner at the 2011 Bosch Media Event, who came running into the room with the Bosch GTS1031 table saw in one hand and a GTA500 stand in the other. Weighing in at a manageable 52 pounds, and this is one 15-amp jobsite table saw that does a great job of balancing portability and raw cutting power.
You can use these saw to cut plywood and other sheet goods, but their compact size makes this a challenge—and a potential safety hazard, if you don't have an extension table, rollers or a human partner to help support the wood on the infeed and outfeed sides. Stick with a circular saw for larger plywood rip cuts, but both of these saws can be workable backups (provided you don't need to rip widths of more than 16 or 18 inches.)
Ridgid’s fence is outstanding for its design. Its large front plate helps stabilize it and the whole thing just feels solid. There’s very little play compared to some of the others and we were consistently able to lock it down perfectly square. We like the pinion style bevel adjustment. It’s not quite a good as a separate adjustment wheel, but a great improvement over simple sliding. We also like the independent locks for both height and bevel. It’s not often that a height lock would be required, but there’s an element of confidence that comes from knowing it won’t be going anywhere.

And finally, there are a couple of jobsite table saws running around with flesh detection to drop the blade out of the way if it detects a strike. There’s a significant premium in cost for these saws and there has also been plenty of litigation regarding whether it should be required on every table saw and whether more than one company has the right to manufacturer the mechanism. But they’ll save you a much worse injury in the event of an accident.


No matter what you need a table saw for, the three listed above are great choices to consider when you’re doing your shopping around. Whether you’re a professional contractor or a serious DIYer, any one of them will have all the features, power, and portability that you could want in a table saw. All of the ones listed here, and most others have warranties and 30-60 day money back guarantees to give you a chance to see if you like them so your purchase won’t be a waste if you don’t, you will be able to get your money back, but we’re pretty sure that if you choose one of the three that we have detailed for you, you’re going to be able to join the many, many customers who are very happy with their purchases.
Make sure you know what’s covered and what’s not, especially if you’ll be using your machine commercially (many warranties are strictly for individual, not commercial use). It’s also a good choice in this case to purchase add-on warranty coverage from a third party at the checkout. We recommend these policies for most portable table saws, since most manufacturers have either very short warranty coverage, or longer warranties which require you to foot the bill for service calls or for returning the machine to the maker.
It's not really a great choice for professional woodworkers, but for home do-it-yourself users looking for a more than competent contractor saw for their workshop, the Ridgid R4512 is a terrific value. It lacks the SawStop's safety features, but comes in at less than a third of its price. Build quality is first rate, most users say, with a cast iron table that does good job of damping down vibration. Users add that it cuts smoothly and accurately.
The design is quite good. The SawStop safety system ensures smooth and flawless operation while protecting you from a variety of hazards. However, regardless of the safety aspects, you should always wear protective equipment, especially gloves and goggles. One of the most notable things about the design is the fact that it provides 99 percent dust collection both below and above the table. The riving knife maximizes kickback and also offers protection.

All table saws sold in the U.S. come with a riving knife, anti-kickback pawls, and a split blade guard. Because some cuts can’t be made with these safety features installed, they are removable. If you’re looking for a fun party game, see who of your uninitiated friends can install both correctly without a manual. While each one is different, their nature means you can use the saw without them installed. I’d be remiss if I didn’t tell you those cuts are more dangerous, so avoid it if you can.
Cutting a board to length by using the fence as a guide is one of the most dangerous yet very common techniques. The fact that it’s quite common among DIY-ers doesn’t make it safe. In fact, it’s extremely dangerous and can lead to fatal consequences. There is a high risk of kickback if you’re using this particular technique. Needless to say, the forces involved are immense, and you’ll end up with a piece of wood in your face. One could say – “But, I’m wearing safety goggles!” Even though it may be true, goggles won’t do much against a dense piece of wood flying straight to your face a few hundred miles per hour.
Contractor saws are a perfect balance between functionality, manoeuvrability and price. These sorts of saws are perfect if you have bigger projects that you’re working on and will stay on site for a few months. This is due to the fact that they are a lot less portable, but that being said they are a great in-between saw as they still have great rip capacity and overall cutting power.

Look for guards with two independent panels on each side of the blade, so that while you work on one side, the other side keeps dust in the vacuum system, rather than flying off to the side. High-end cabinet units also have splitter and guard systems which are molded like the internal shrouding to amplify suction, so you should look carefully at those features.
If you’re going to have a quality product, you need a fence system that’s perfectly square to the table so your cut is perfectly parallel to the edge. Obviously, framers have a bit more leeway than jobsite carpenters and there’s plenty of variance in fence quality. Cheaper saws have fences that can easily move out of square as they slide along the surface of the table. Avoid these if you want quality results. The fence system needs to be easy to keep square to the blade.
While a lot of other Dewalt saws let us down in the dust compartment, the company have made big strides with this model. It has an internal canvas housing around the blade chamber, which keeps dust from spraying around inside the machine, without having the limitations of a rigid shield. It’s not perfect, but it does much better than the Bosch or the cheaper Dewalt.
Framing work is full of rougher cuts that rarely makes use of more than one blade at a time. But occasionally you might need dados for an onsite custom build in. If that sounds like you, be sure to find out the saw’s dado stack capacity. It requires a longer arbor and you won’t be able to use your normal throat plate for it. Some manufacturers offer a dado throat plate if they have the capacity for it.
We really should point out a big deal here and that’s the SawStop. It’s hard to put a price on safety and while the SawStop costs more than 3 times what the Hitachi costs it does offer safety that no other saw in test can offer. For those that can afford the additional cost that feature alone may tip the scales for you. Regardless of price SawStop came in 5th place for the categories we evaluated.
The Grizzly is our top choice for folks who need lots of room to work, plain and simple. Thanks to its dual extension tables, this one has the widest rip and fence capacity of the three units we’ve reviewed here. We also love that it makes full use of the space under the worktops, so you’ll get plenty of storage room to make up for its larger footprint.
One thing you’ll love about the riving knife is that it allows for adjusting the table saw without using any special tools, for non-through and through cuts including, pictures frames, grooves for shelves, but also cheek cuts for furniture, rabbets and dadoes. There’s also the possibility to store different tools or anything else you may find under the tablet board and given the fact it’s expandable and convenient, it’s going to make using the Delta 36-L552 an even more amazing experience. For dust collection, the table saw comes with a bi-level dust extraction system which offers superior dust collection capabilities.
In other words, a malfunction might mean an injury. This distinction could not be more pronounced in any other job site equipment than a table saw. I have personally witnessed devastating injuries on a number of occasions that could have easily been avoided by the use of safety equipment that comes standard on most brand name saws. Liability for a job site injury can be a serious setback for well established companies, but for small, independent contractors it could mean the difference between business and bankruptcy.

Other features include a battery-powered laser for lining up cuts. I found it to be pretty dim under bright shop lights and not lined up correctly with the blade. It is non-adjustable. A pullout rear extension provides some added support for long rip cuts. Rockwell also offers a couple of unique accessories: a sliding miter table ($179.99) and a power planer-style “Finisher” ($129.99). It mounts on the saw for flattening board edges.
TBB measured the accuracy of the factory-set 45 degree stop by using a Wixey WR365 digital inclinometer. This device has an accuracy of 0.1 degree. We placed the Wixey gauge on the table and calibrated the inclinometer to the table by zeroing out the gauge. After that calibration, the measurements shown on the gauge give a result that is relative to the saw table. We attached the gauge to the blade and used the saw mechanism to adjust the blade incline to the point at which the blade or trunnion hit the factory-set 45 degree stop and recorded the measurement. TBB ran the test twice to ensure the repeatability of the measurement. In every case, the result came out to within 0.1 degree of the prior test.

Belt drive table saw motors run on a pulley system, most of the time some power is lost through this system, but belt drive blades can cut through thicker timber and hardwoods. They can produce power of around 3 to 5HP and thanks to the motor being mounted further away from the blade with belt drive, the motor will last longer as less dust will get into the motor. One thing to consider though is that belt drive will be in general more expensive and are normally found on heavy cabinet type saws, so this must be considered when working out your budget.
One of the things we looked at was the ease of assembly out of the box. We had the same person assemble each of the saws and timed the assembly to see if there are any significant differences between the models. The assembly time for the saws ranged from 21 minutes to 48 minutes. While some stands required more than twice the time, we felt the assembly time was not a significant enough factor to change someone’s mind on which saw to purchase.
A magnetic switch is also good from a safety standpoint but may not be necessary on these smaller versions. A magnetic switch prevents the saw from starting back up if it loses power during a power outage. Basically, the power outage will turn off the saw. This is good because if for some reason the power were to come back on when you were not near the machine, the material could be shot out of it or damage the saw.
We absolutely love the Dewalt DWE7491 that we recommended as our top quality choice above. It’s a powerful, precise workhorse that can handle nearly any cutting job. However, times are changing fast, and workplace safety standards are increasing just as rapidly. If you’re a professional who wants to stay on top of your code, you should consider getting a unit that’s equipped with a flesh-detections safety system.

The thing you might not like about it is the non-flat table top. Many people find this downside as quite a burden, especially if you’re processing perfectly flat wood. Also, the protective coating on the top side of this model is pretty subpar. In fact, it barely protects anything. Consequently, it will peel off quite quickly. As far as the price goes, it’s okay, but it could have been a bit cheaper.

When it comes to power tools, table saws provide convenience when tackling DIY jobs or larger commercial tasks. With their table surface, you are able to get more accurate cuts with the materials you are working with. Utilizing the miter gauge, you will find these power tools to provide the same accuracy as your favorite circular saws without the hassles.


Along with thinking about how the table saw will be used now, it is important to also consider how you will be using it in the future. Will your usage increase or decrease? Many woodworkers may turn a hobby into a fulltime profession if they are talented at what they do. Why are these considerations important? Because they will give you better insight into the kind of money you should spend on your table. If you are going to go into business for yourself in a year or two, spending the money for a high-quality table now is a good idea. It will save you from having to buy another table in the future to accommodate your new needs as a business rather than just a hobbyist.
The integrated blade carries an electrical signal. Once it comes in contact with human skin, the signal changes because of the skin’s conductivity and the blade immediately stop. Although some people don’t like the process of resetting the blade, it’s quite easy, and it takes only a couple of minutes. If you think about it, it’s better to hassle by resetting the blade for five or six minutes instead of losing a few fingers.
Editor and "serious woodworker" Chris Marshall tests five "premium" portable table saws. After equipping each saw with a new Freud thin-kerf blade, he uses them to rip lengths of medium-density fiberboard (MDF) and yellow pine, as well as making long dado cuts in MDF. Marshall considers the saws' stability, cutting accuracy, efficiency, dust collection, and general ease of use to choose his top picks. Unfortunately, two of his three favorites are discontinued.
If you want a table saw that helps you deliver products faster, the Bosch 4100-09 could be what you’ve been waiting for. It has a Gravity-Rise stand that is built for efficient and accurate setup and takes down.The portable construction makes it easy to bring to any worksite with minimal trouble. Only weighing 39 pounds, you will have no problem transporting this table saw wherever you need to go. The Bosch 4100-09 is a powerful saw that is made for the kind of high precision cutting that professionals and DIYers are looking for. It has a 15 AMP, 4 HP motor that generates 3,650 RPMs for clean cuts every time.
PLEASE EXCUSE THE PICTURE, LUMBER JOCKS REQUIRED ONE. I AM AWAY FROM HOME AND COULDN’t RUN OUT TO THE GARAGE TO SNAP A SHOT. I am writing a review of my Bosch saw after a few months of use. I bought this saw last November after my Ryobi saw up and died during a project. I looked at several saws in the $600-$800 range and narrowed it down to four options. The Bosch and DeWalt jobsite saws, and the Delta and Ridgid contractor saws. My requirements were in a realativly compact saw th...
Setting up both saws was quick and easy, since their factory-adjusted blades and fences were square and parallel to the tables' miter gauge slots out of the box (this is one of the reasons to buy a $350 table saw over a $100 one). Both saws had similar setup procedures: Attach the fence, raise the riving knife, attach anti-kickback pawls and attach the blade guard. There is no on-board stowage space for the DW745's rip fence, but this does not really affect the setup time or effort by much.
Both of these table saws have a port that connects to a shop vacuum for dust collection. The DEWALT features a 2.5” port, while the Bosch has a 2” port. However, neither seems to do all that great a job. The Bosch might fare a little worse as far as the dust port clogging, but the DEWALT has some problems in this area, too. The Bosch is said to spew sawdust on the floor as though there was no dust collection port at all. The DEWALT racks up some complaints about the same problem.
In terms of features, the SawStop ICS51230-52 comes with a patented safety system that prevents injuries and serious accidents and offers users the highest level of protection during use. Thanks to its 5HP, you can easily cut hardwood of 5 inches or even thicker without having to worry about the saw choking. Also, thanks to the toll-free fast change mount, you can transition between riving knives and guard in just a few seconds.
How many teeth a saw blade has will determine how smooth the cut is. Most blades have from 24-80 teeth. The exceptions to these blades are specialty material specific blades (i.e. for masonry) In general, the more teeth a blade has the smoother the cut will be. The higher tooth count means that the cut speed will be slower as well. You cannot overcome a slower cutting speed by pushing harder on the material. This is a common mistake newbies make. All this will do is cause kickbacks when the saw blade catches and tosses the object back towards to the user at dangerously high speeds.

As we already said, people tend to remove the safety elements to speed up their projects. Needless to say, it’s a huge mistake. Those things are there for a reason, and they should remain installed at all times. As soon as you mingle with the parts, you’ll jeopardize the integrity and your own safety. Even the best table saw cannot protect you enough if you mess with the parts on your own.

I build guitars in a small shop; I need my saw to be accurate, repairable and easy to store or move. I love this saw! I use it for everything from cutting down stock to slotting my fretboards. It gets out of the way, it came dead on square, and the dust collection works pretty well with a shop vac and great with a high volume dust collector, with an Incra miter fence it makes perfect, repeatable, and accurate cuts. After I had owned it for over a year the plastic lever on the riving knife broke - I called Bosch and they "goodwilled" me a new riving knife assembly (with an upgraded metal lever) via express mail. No charge and fast, friendly service - they didn't even ask for a serial number or proof of purchase. I'd buy this saw again in a minute - all tools wear out or break at some point and I really like that the company stood behind this one and got me up and running again in a hurry. I also love all the safety features - riving knife, anti-kickback pawls, large easy-to-reach power button, nice push stick, and a dust collection port that is positioned out of the user's way.


In other words, a malfunction might mean an injury. This distinction could not be more pronounced in any other job site equipment than a table saw. I have personally witnessed devastating injuries on a number of occasions that could have easily been avoided by the use of safety equipment that comes standard on most brand name saws. Liability for a job site injury can be a serious setback for well established companies, but for small, independent contractors it could mean the difference between business and bankruptcy.
Before we get into some of the top features, we want to take a look at the design of this cabinet. As it uses an enclosed cabinet, you’ll find that the motor lasts longer because it doesn’t wear down due to constant exposure to dust. This cabinet also features convenient hand wheels on the front and sides that help you make quick adjustments before cutting or as you work.
Rockwell diverged from the crowd with this offering. For starters, the riving knife, anti-kickback pawls and blade guard are connected and remove as a unit. If you do remove them to make a non-through cut, you have to install the separate riving knife first. It’s not difficult, just different. This is the only saw with a right-tilting motor. We prefer left-tilting motors because it’s safer to make bevel cuts with the fence on the right side of the blade. There’s no port for attaching a vacuum cleaner, but there’s a large dust bag that does a good job of collecting sawdust. This saw cuts 3-9/16 in. at 90 degrees, 1/16 in. more than the next closest competitors, allowing you to rip a 4×4 in one pass. And like the Ryobi saw, it has a 30-in.-wide rip capacity.
In terms of features, the SawStop ICS51230-52 comes with a patented safety system that prevents injuries and serious accidents and offers users the highest level of protection during use. Thanks to its 5HP, you can easily cut hardwood of 5 inches or even thicker without having to worry about the saw choking. Also, thanks to the toll-free fast change mount, you can transition between riving knives and guard in just a few seconds.
This one’s compatible with Jet’s rolling bases. You can mount it on any of the company’s all-metal roller frames, and move it around your shop! That’s ideal for busy shops with a lot of large equipment and not a lot of space to spare. It’s also handy for home craftsmen who don’t have as much dedicated space as they’d like to devote to a table saw. The Grizzly, on the other hand, is much harder to convert to a wheeled base, because it has the dual extension tables.

One of the things we looked at was the ease of assembly out of the box. We had the same person assemble each of the saws and timed the assembly to see if there are any significant differences between the models. The assembly time for the saws ranged from 21 minutes to 48 minutes. While some stands required more than twice the time, we felt the assembly time was not a significant enough factor to change someone’s mind on which saw to purchase.


Measuring 30.31" x 17.32" x 41.81", this powerhouse boasts a heavy duty 10" blade that can cut up to 4" x 4" of material in a single pass. For the handyman who likes to keep all of his tools within arm’s length, RIDGID’s table saw comes with convenient onboard storage so swapping out blades or accessing your tools is just a short reach away. Buyers are crazy for this table saw, and they report that it easily fits into the corner of their garages. Plus, quick and easy assembly means you can get to work straight out the gate.
×