The GTS1031 is Bosch's newest table saw, designed for portability and intended to be light enough that you could carry it with one hand. Its rip fence is designed for quick and easy movement, and clamps into channels on opposite sides of the table to keep things consistently square without the need for frequent adjustment. Two notable advantages for the GTS1031: Its 5000 RPM max no-load speed compared to the 3850 RPM for the DeWalt, and the fact that you can use a 1/2-inch dado set with it (though it requires separate TS1013 dado throat insert).
DeWALT DWE7480 is an excellent table saw, especially if you consider its price. It’s a step up from the highly popular DW745 and slightly more expensive, but I think the larger rip capacity and higher RPM are well worth the extra money. The DWE7480 is still in the lower price region though, and unlike the DW745 you can also get this one with a stand: the DWE7480XA!
TBB measured the accuracy of the factory-set 90 degree stop by using a Wixey WR365 digital inclinometer. This device has an accuracy of 0.1 degree. We placed the Wixey gauge on the table and calibrated the inclinometer to the table by zeroing out the gauge. After that calibration, the measurements give a result that is relative to the saw table. We moved the blade to an approximate position of 70 degrees off vertical. TBB attached the gauge to the blade and used the saw mechanism to adjust the blade incline to the point at which the blade or trunnion hit the factory-set 90 degree vertical stop and recorded the measurement. TBB ran the test twice to ensure the repeatability of the measurement. In every case, the result came out to within 0.1 degree of the prior test.
Safety is a prime concern for Bosch. From the SquareLock Rip Fence through to the patented SmartGuard System to lessen any chance of kickback, your security and comfort is taken care of. The blade guard and riving knife are quick-release. This takes away any excuse for not putting the guard back in place because it would be too much trouble, something that’s an accident waiting to happen.
The SawStop Contractor Saw CNS175-TGP36 stands out chiefly on account of its unique safety brake, which stops the spinning blade dead when it senses the presence of skin. However, it's also an excellent saw in other respects: powerful, well built, and easy to assemble, with great dust collection and loads of features. Cost is a major concern, but so is the cost of the injuries SawStop is designed to eliminate.
Choosing the best portable jobsite table saw wasn’t an easy task but we’re confident we’ve done a thorough evaluation. In a very close race for the best table saw Hitachi beat out the DEWALT which came in second place followed by Skilsaw in third and Makita in fourth. It’s very interesting that the Hitachi and DEWALT look extremely similar. Hitachi edged out the DEWALT in performance and price resulting in the final scores. Skilsaw beat out Makita for the 3rd place only slightly and that result is really a function of pricing.
You will agree that your ability to hold, controlling and manipulating the saw largely depends on your strength. Since small table saws are lightweight, you should go for a powerful table saw so as to avoid fatigue during small jobs. This also means that if you are working in a forest for a whole day the light weight is of great importance it also helps reduce fatigue. When shopping for chainsaws ensure the saw balances well in your hand. You should also ensure that you can easily shift the saws grip from hand to hand without losing its balance.
Blade guards are an important safety device and should never be removed from the saw. You want to find one that rises up parallel to the table so it is always on top of the material you are working with. The purpose of this blade guard is to protect you from the spinning blade. While some woodworkers find them annoying, the safety they provide is well worth the inconvenience.
What if a contractor uses their job site saw for high quality built-ins or high tolerance finished cuts? In that case, saw accuracy is critical for that work. In this use case, if the saw is immediately put into use, success depends upon the out-of-the-box accuracy from the manufacturer. The quality of the cuts and more importantly the potential safety of the operator is going to be a function of the as-shipped accuracy of the saw from the manufacturer.
Bosch’s Gravity Rise Stand was the best portable design of the group. While several stands share the basic principles, Bosch stood out with large diameter tubing that improves durability, the ease of set up/take down, and the larger pneumatic wheels that helps over less than ideal terrain. SawStop was right behind with slightly narrower wheels while Ridgid wrapped up the top 3 most impressive.
Excellent saw. Got here sooner then expected. Fairly simple to put together. Folding stand is very solid and easy to operate. Takes up very little space in my garage. I've never owned a table saw before so I'm easily impressed. Some other buyers recommended upgrading the blade, which I did. The blade it came with was ok but the Freud 10 in. 40 tooth Premier Fusion makes a very smooth cut. I haven't hooked up dust collection to it yet but it seems like it would work great. The scale for the fence is spot on. I would highly recommend this to any diy.
Optional portable table saw stands are available for both saws. (Bosch's stand is called the GTA500; DeWalt's is the DW7450.) The Bosch features tool-less connection (after initial assembly), while the DeWalt requires the attachment and tightening of four bolts through the DW745's bottom roll cage— though it's nothing a few after-market knobs couldn't fix.
When it comes to power tools, table saws provide convenience when tackling DIY jobs or larger commercial tasks. With their table surface, you are able to get more accurate cuts with the materials you are working with. Utilizing the miter gauge, you will find these power tools to provide the same accuracy as your favorite circular saws without the hassles.
Table saws will use one of two different kinds of drive configurations; Direct-drive motors and Belt-drive motors. In a direct-drive motor, they will link directly to the blade itself and transfer all of the power of the motor to the blade. They tend to last longer than belt drive motors and there is no belt to replace or worry about getting worn out. Belt drive motors transfer power from the motor to the blade through a belt. In this type of configuration, the motor can be offset away from the sawdust which helps the motor last longer. In general, belt drive motors need more preventative maintenance than direct-drive motors do. If you have a belt drive motor, check the tension of your belts as well as checking them for wear periodically to ensure your continued safety.
The throat plate is the removable piece surrounding the blade that sits flush with the table. Removing it gives you the ability to access the blade for removal or riving knife adjustments. The narrower the blade clearance the better for two reasons. First, it helps keep material from falling into the blade area or lodging between the blade and throat plate. Second, it gives you material support very close to the cut to help reduce tearout as the blade exits the cut.
Rockwell is the “freshman” brand among the other longer-standing benchtop power tool companies represented here, and its table saw revealed some “first rodeo” shortcomings. While the motor was amply powerful for my cutting tests, the blade arbor assembly was 1/16″ out of parallel with the miter slots. It’s a condition called “heeling” without easy adjustment in the manual. So, for my testing purposes I had to set the rip fence askew in order to align it parallel to the blade. The problem would need to be addressed on this sample saw for long-term use.
I definitely give this one 5 stars, but this is specific of the application – it being portable. If I was comparing it with other Hybrid saws, than this one doesn’t really compare when it comes to power. That being said. I was shopping for a table saw, after many years of working with a circular saw, and a straight edge – for me – it was time to get a setup for repetitive cuts that would be easier, and less time consuming (not to mention more precise, as the machine...
Bosch’s 4100-09 work site table saw is a sure win. Bosch never fails to impress us, and this table saw is no exception. It’s a 10 in. saw with a 25 in (right) rip capacity and a 47 degree left bevel. This Bosch table saw is powered by a 15A motor that reaches top speeds up to 3,650 RPM. Another feature we appreciate: its constant response circuits which continuously adapt the speed under load, giving you a continuous blade speed.
The saw itself is remarkably compact, measuring just 22.5″ square and a little over a foot in height (13″ to be more precise). With a steel “roll cage” that encloses the 4 HP 15-amp motor and a rubber handle that is positioned in the center of the right side of the saw, this is a tool that you’ll find very easy to toss into the back of a pickup or work van and take to any jobsite. When you carry it deck-inward, the weight of the saw presses in slightly against your leg – which actually steadies the saw somewhat, making it more manageable, though at 52-pounds let’s not go so far as to call this saw a breeze to carry. The Bosch GTS1031 included cord wrap, and the simple design of the frame also makes it easy to store up against a wall inside your shop when not in use. This isn’t a tool that really gets in the way much – it’s out of sight until it’s needed.
Because we’re passionate woodworkers who care deeply about the quality of the tools we work with, we have a tendency to recommend that even the most budget-conscious buyer spend a little more to get something high-quality. However, we know that some DIYers might have the ambition to take their woodworking to the next level with a table saw, but might not necessarily have the funds.
First, consider the types of cuts you’ll need to make, and which types of stock you work with on a regular basis. Think about the largest rip cuts you need to make, and get a cabinet saw with a suitable max capacity for rips. Find the thickest stock you need to cut, and make sure your new machine has a high enough depth capacity to make the cut cleanly. The larger your average stock, the larger a workspace you’ll need on your new cabinet unit. It’s also a good idea to think about bevel and miter cuts which you’ll be making on your table saw. All of our recommendations have the capacity for both, but some come with miter gauges and others don’t.
We made a few test cuts with ¾-inch plywood just to get a feel of the motors we were working with. It became clear pretty quickly that not all 15 amp motors are equal. Once we knew what to expect, we moved to pressure treated 2x pine material in 7-1/2 foot lengths. Why 7-1/2? Our test material started at 15 feet and it seemed silly to have some at 8 feet and others at 6.
The most critical safety feature on a table saw is the blade guard. It’s all that separates your fingers from the rapidly rotating blade. You need this to be transparent or it will make measuring awkward. The last thing you want is to be tempted to remove an unfit guard. Check closely for a clear, flexible blade guard. Safety is paramount when operating a table saw.
I decided to do the very same thing a while back. I thought it would take a few days to figure out everything about table saws and then just buy one. I was dead wrong. While table saws are simple in their construction, they are complex because there are so many factors, so many aspects, and so many different features to consider. After spending a large amount of time doing my homework, I decided to share what I learned with you, in the shape of table saw reviews and informational articles. Before you actually go and read them, let me take you on a quick walk through the website so you know what there is and where you can find it.
Now, don’t get me wrong, there are other portable table saws that are lighter than Bosch’s GTS1031 (who’s name sounds like a cross between a fast production car and a tax document). The key with the Bosch is that it’s jobsite tough. Give the other saws some wet lumber or run them all day long and you’ll smoke the motor, bog them down, or send them off a second story porch in frustration. Bosch seems to have designed the GTS1031 with two things in mind: portability and power. Portability, because all of the accessories store right on-board, and they do so securely, so they won’t fall out, even if the saw is bumped and tossed around – as jobsite saws tend to be.
The DeWalt, Bosch and Ridgid saws have strong stands that are easier to set up, sturdy fences that lock down parallel to the blade every time, and smooth-operating blade controls. If you’re a contractor or an avid DIYer who just likes top-quality tools that feel good and last a long time, we think the extra few hundred dollars is a good investment.
Using the guards the saw came with is crucial for the safety of your hands. If you are working with smaller pieces, make or buy a sled with a work clamp so that you can maintain a safe distance from the blade. The clamped sled can be as simple as a piece of plywood with a track on the bottom that’s responsible for riding in the groove. It’s quite simple to construct, saves time, and most importantly – fingers.
The integrated blade carries an electrical signal. Once it comes in contact with human skin, the signal changes because of the skin’s conductivity and the blade immediately stop. Although some people don’t like the process of resetting the blade, it’s quite easy, and it takes only a couple of minutes. If you think about it, it’s better to hassle by resetting the blade for five or six minutes instead of losing a few fingers.
The whole thing is a bit more versatile than the Dewalt, thanks to expanded fence rails and an extended trunnion set. It has a wider rip capacity than the Dewalt. This one uses a traditional sliding-rail fence which gives you a rip capacity up to 25 inches. The fence locks at either side, like the Dewalt’s. It also has a wider bevel range, tilting up to 47 degrees.
One of the lightest and most compact table saws was also the most stable: Skilsaw. There’s no wheel base to the stand and the outward angled legs provide a wider platform than it may appear against its colleagues. In second place was DeWalt, also offering a wide platform, but without the amount of rigidity that Skilsaw has in their stand. Coming up in third was Bosch with its gravity rise stand followed closely by Ridgid. It’s important to note that none of the professional class table saws had any stability issues inherent to their extension locking—it was all in the stand.
If you’re going to use your table saw every day, make sure you spend a bit more money for something of the heaviest build quality, with extended warranty coverage from a company with a great reputation for service. If you’re going to be using your cabinet unit only periodically, you probably don’t need to buy something premium. You’ll be able to get by with something around the $2,000, since you won’t be spending enough time cutting to really appreciate the design touches and tweaks that make the more expensive units more of a pleasure to use.
Measuring in at 19.9" x 23.4" x 13.4", the SPT70WT-01 is compact enough to fit into any aspiring handyman’s garage, but powerful enough to tackle anything you throw at it on the job site, meaning it’s an ideal entry-level table saw for the amateur hoping to turn his hobby into a career. Sturdiness, durability, and anti-kickback technology make the world’s first worm drive table saw a revolutionary machine. Satisfied buyers can’t get enough of this balanced wood-devouring behemoth.
All seven saws in the best table saw testing have some kind of dust control. The Rockwell saw has a completely enclosed motor compartment with a large dust bag that attaches under the saw to catch sawdust. The remaining saws have a shroud around the blade and a 2-1/2-in. port on the back for attaching either a bag or a vacuum cleaner. None were perfect, but at least you can catch most of the sawdust. The Craftsman and Ryobi also include a dust bag that attaches to the vacuum cleaner port.
You’ll make most of your miter cuts on a miter saw. But when the material you’re cutting exceeds a miter saw’s cross-cutting capacity, you turn to your table saw miter gauge. These usually aren’t quite as precise, but some manufacturers put more thought and robustness into it than others. If you make a lot of long miter cuts, be sure to pay attention to this accessory.
How many teeth a saw blade has will determine how smooth the cut is. Most blades have from 24-80 teeth. The exceptions to these blades are specialty material specific blades (i.e. for masonry) In general, the more teeth a blade has the smoother the cut will be. The higher tooth count means that the cut speed will be slower as well. You cannot overcome a slower cutting speed by pushing harder on the material. This is a common mistake newbies make. All this will do is cause kickbacks when the saw blade catches and tosses the object back towards to the user at dangerously high speeds.
Bosch’s REAXX and SawStop were neck and neck with near perfect cleanup at the collection point and only a slight amount of dust coming out toward the user. What did make it out was even less coarse than the other Pro level saws. Both saws have narrower throat openings for the blade that reduce the amount and size of material that can make it out. In the end, SawStop produced less top dust than Bosch did to earn the win.
When your skin contacts the blade even slightly, the charge transfers, and a switch flips on the motor, activating an instant brake. The aluminum brake swings into contact with the blade, stopping it instantly. The brake also propels the blade down through the arbor, so it retracts completely below your worktop. That means that other than the initial contact, you won’t touch the sharp edge at all.
It features an 1850W motor which delivers more than enough power for any heavy-duty task and DIY project. Dewalt is well-known for designing quality tools, and they didn’t disappoint with this particular model either. The fence system offers 610mm of rip capacity. As you may assume, even though it’s a portable unit, you can easily cut large pieces of wood to a particular size.
Even though the trunnion mechanism from Powermatic has been known to be the best there is, further refinements have been made to it in order to make it even better. The conically shaped worm gear drive with better surface area, the high end bearings, but also the cast iron, box style construction combine with the solid and smooth feel of the height and tilt adjustments. Thanks to the adjustable backlash, it’s very easy for users to adjust the mechanism back to the factory fresh feel and clearances.
These are the best choice for long jobs where you’ll get yourself set up at a job site, and need a saw that enables you to make all your big, long cuts without traveling back and forth between the site and your shop. While you won’t want to move these units around frequently, they’re great for seeing a contract through to the end from the worksite.
As with our other models, it takes some assembly. If you get one of the extended models, which we’re recommending here, you should plan to cut the rails down to size before finishing installation. It’s simple to do if you’ve got a good miter or bandsaw, but it is an extra step. With that said, many reviewers complimented the SawStop’s well-written and helpful manual, which made installation significantly easier than other units.
The Dewalt DWE7491is the clear choice for the full-time woodworking professional. It provides the widest rip capacity by far, it’s the fastest worker, and it has the best dust collection. The fence is a thing of beauty, and the secondary inner fence is a smart feature for smaller cuts. We think it’s worthy of any full-time woodworker, or DIYer with plenty of shop space and spending money.
If you're currently looking for a cabinet table saw and it's the first time you actually need to buy one, then you should know that they come in a wide range of types, from the larger contractor saws to the portable table saws that most people seem to own. However, buying the right model for you depends on your needs and how you're going to use it.
Like the Bosch, this Dewalt comes with a rolling stand. It’s convenient to set up and take down, since you can do it without helpers or tools. It rolls like a dolly, and opens into a nice, sturdy table. We especially like the splayed legs, since they lend the whole thing a bit more stability than the Bosch version. Unlike the Bosch’s stand, the Dewalt’s has semi-pneumatic tires which won’t ever go flat.
Replacing the hugely popular outgoing W1824, the W1851 is a brand-new Shop Fox hybrid with the same enclosed cabinet as you’ll find on the W1819 alongside features more in line with a contractor’s saw. We chose to review the W1851 as it’s a more flexible option than the W1819 and appeals to a broader range of woodworkers. We rarely review brand new products but in this case we made an exception… With a brand like Shop Fox, it’s not a case of taking a chance but of betting on a winning team.
Skilsaw produced the only worm drive table saw in our group and we had high expectations, especially given the high RPM count. In the end, the power is definitely at the professional level and settled in tied for fourth overall with DeWalt. This was the lightest, most compact saw in the group. Like DeWalt, the lack of an outer housing leads to more efficient cooling but drops storage for an extra blade.
A magnetic switch is also good from a safety standpoint but may not be necessary on these smaller versions. A magnetic switch prevents the saw from starting back up if it loses power during a power outage. Basically, the power outage will turn off the saw. This is good because if for some reason the power were to come back on when you were not near the machine, the material could be shot out of it or damage the saw.
Reviewers recommend these models for easy transport to jobsites and for easy storage in a small workshop. Portable table saws come in two types. Benchtop saws sit on top of a workbench and are light enough to pick up and carry; jobsite saws are mounted on folding stands, usually with wheels for easier transport. The main drawbacks of a portable saw are its lower power and smaller table, which makes it tricky to cut larger lumber and sheet material such as plywood. Prices for portable saws start at less than $200, but the best-rated models typically cost $300 or more.
Move the wood to and then "through" the spinning saw blade slowly and steadily. It's alright to use your hands while you're still at least a foot or so from the blade, but once the end of the board or sheet nears the blade, you should use a pushing stick to keep the wood moving and to keep your fingers away from the blade. Even an experienced carpenter can have a lapse in concentration or a slip that can lead to serious injury.
Some previous buyers had motor trouble. Their units conked out early, or worked inconsistently. Apparently, that was down to cheap internal bearings used in the first few iterations of the Bosch. However, according to company replies to some reviewers who cited the issue, the problem has been addressed in the last few versions of this model. We’ve also found that reviews from the past few years are much more consistently positive.
The Powermatic used to be another all-American classic, much like the Delta. This latest version has the same recognizable yellow finish, on a steel cabinet and cast iron worktop. Unlike most other cabinet units, this one has cast-iron extension wings, which makes them just as sturdy and level as the central worktop. It’s loaded with a 3 HP motor, a 50-inch fence, and all the other basic features that our top three picks have.
In our introduction and how-to sections, we’ve talked about some of the key reasons to buy a cabinet-style model. These are the most stable table saws you can find. They produce the smoothest, cleanest cuts. They’re also tools that are built to last a lifetime. We recommend them to any professional with the shop space to install one. They’re also the ultimate choice to ardent hobbyists with plenty of room to spare and an ample budget.
Kenny Koehler An avid endurance athlete, Kenny has competed in triathlons (he's an Ironman) and various other fitness activities. Still, his passions lie with his faith, family, friends, and his love for well-designed power tools. With a background in science, you'll often find Kenny chatting up engineers at media events to get caught up on the latest tool technology.
Table saws in this best table saw review run the gamut in price and quality. You can buy a table saw for as little as $150, and if you use it just to occasionally rip a board, that may be all the saw you need. If you want a saw that’s easy to carry and you don’t need to rip sheets of plywood in half, look for a “compact” saw like the DeWalt DW745 (shown) or the Bosch GTS1031. If you have room for a little larger saw that’s slightly less portable but capable of wide rips, consider one of the best table saws we review here. And finally, if you want to build cabinets or furniture and have a big enough work area, you can step up to a stationary contractor’s saw like the Ridgid R4512 (shown), for about $650.