I appreciate the helpful comparison of the best table saws. I’m fairly new to woodworking, and until recently I was using an old table saw that used to belong to my dad. Long story short, it’s no longer usable, and so I’m looking for a good table saw to buy that’s beginner-friendly. I have my eye on the DEWALT DW745 – evidently it’s really popular and does a great job. I’ve taken a look at some other sites for more ideas. Your guide here is great. What is your opinion on the DW745?

After spending hours doing a lot of research and talking to professionals who use these tools on a regular basis we have put together a review for you that not only tells you three of the top table saws on the market today, but we tell you why they are popular and explain a bit about each so you have a good idea of what they are like. This table saw review will put much-needed information right at your fingertips so you can make a good decision on the right table saw for your needs.
The blades are the primary factor to consider when shopping for a saw as they hugely determine the performance of your table saw. The blades will only be effective if they are set at a correct depth of cut. The table saw will also perform best if only the correct blade for the cut is fitted, as a proper blade will enable you to achieve a precise and smooth cut. When purchasing a blade, go for the one with a correct setting blade. Consider the cutting depth also as this will determine its suitability for the job. You should also ensure that the table saw is equipped with splinter guard as this will help in minimizing splintering of the board’s top surface. Splinter guard also enhances accuracy because when it is lined up at the start and finish mark the saw will cut with precision. A suitable table saw should also have a 20mm arbor as this guarantees the stability of the blade and hence, safety in the workplace.

Bosch’s REAXX and SawStop were neck and neck with near perfect cleanup at the collection point and only a slight amount of dust coming out toward the user. What did make it out was even less coarse than the other Pro level saws. Both saws have narrower throat openings for the blade that reduce the amount and size of material that can make it out. In the end, SawStop produced less top dust than Bosch did to earn the win.


Some previous buyers had motor trouble. Their units conked out early, or worked inconsistently. Apparently, that was down to cheap internal bearings used in the first few iterations of the Bosch. However, according to company replies to some reviewers who cited the issue, the problem has been addressed in the last few versions of this model. We’ve also found that reviews from the past few years are much more consistently positive.
I also added in a bicycle saddle bag, that attaches easily to the tube frame of the saw. In it, I keep my PPE, and my Grr-ripper push blocks (great upgrade over regular push blocks). I also have a push stick made of wood that was modeled after the plastic one mounted on the back of the saw. The wood one is there now. I read too many stories of injuries after the blade touched the plastic stick, which to me is the whole point of using a stick – to avoid injuries. These things turning to shrapnel seems like a bad idea.
Another important safety feature to consider is a magnetic switch. Magnetic switches are there in case of power cuts or outages and will also protect the table saw motor from over load. Effectively it will switch off the power supply the instant the power goes off ensuring you don’t have a saw blade spinning away in the dark! As you can imagine this is a very useful and must have safety feature when looking to purchase a new table saw.

Finally, hybrid saws combine the lighter weight of the contractor saw with the more powerful motor and sturdier construction of the cabinet saw, at a price that’s easier for the occasional woodworker to stomach. They can run about $1,200 or so, and weigh in at under 300 pounds. Their motors are generally in the 1.5 to 1.75 HP range, and can be used with standard 110V outlets.
First, consider the types of cuts you’ll need to make, and which types of stock you work with on a regular basis. Think about the largest rip cuts you need to make, and get a cabinet saw with a suitable max capacity for rips. Find the thickest stock you need to cut, and make sure your new machine has a high enough depth capacity to make the cut cleanly. The larger your average stock, the larger a workspace you’ll need on your new cabinet unit. It’s also a good idea to think about bevel and miter cuts which you’ll be making on your table saw. All of our recommendations have the capacity for both, but some come with miter gauges and others don’t.
The DeWalt will do you proud for a broad spread of applications. If you’re a home woodworker, you’ll be able to rip sheet material, size material as thick as 3 inches, frame lumber and make cross cuts to your heart’s content. For professionals, the DeWalt is perfect for trim carpentry, installation of hardwood floors, decking or remodeling. There’s very little you can’t do with this beast.
While a lot of other Dewalt saws let us down in the dust compartment, the company have made big strides with this model. It has an internal canvas housing around the blade chamber, which keeps dust from spraying around inside the machine, without having the limitations of a rigid shield. It’s not perfect, but it does much better than the Bosch or the cheaper Dewalt.
The rip fence has a nifty flipping action so you can hold 2 different positions. This is an awesome feature if you’re cutting especially narrow workpieces. One of the dangers of ripping substantial pieces of lumber is breakage or the saw itself toppling over. The rail extension gives wonderful stability and allows you the freedom to undertake ambitious projects in complete safety.

We recommend something with this technology for new woodworkers, instructors, or folks who work in a busy shop with lots of movement around them. They’re also a safe bet for buyers who simply like to take as many precautions as possible. The only downside to these systems is the price. You’ll find them on machines closer to the $3,000 mark, as a rule.
Before you decide to invest in a unit, you must first know what to look for in order to find the best table saw. Many people think buying a table saw is a piece of cake, but the reality is completely different. There are a few things you should think about before buying one, especially if you don’t have any previous experience. Take a moment and read this article, it will help you a lot.
Dust capture from this saw is pretty bad. I was shocked that a European brand would ignore the dust collection to this extent – at least I was until I discovered that their version of the 4100 does have quite a few more pieces that help pull most of the dust from the airstream. There is a plate that encloses the rear around the vacuum port and a bottom grid that allow airflow to the motor while still shaping the airstream to drive the dust to the vac. I added the plate, but decided against the grid. Instead, I added a sheet of ¼” plywood and put a 4” vacuum port in it that I hook up to my dust collector. I also replaced the blade guard with the European version that has a dust port built in. Minor upgrades, but dust capture has gone from terrible/non-existent to pretty acceptable. Bosch also sell a bag that will capture whatever dust would get tossed out the back of the saw, but that isn’t much, so I consider it a waste. I did buy it, and it works well on other tools, but it is not IMO a must-have for the 4100
When I switched blades, I did find the locking lever for the riving knife very stiff … not sure why. It raises to release the riving knife and pushes down to lock it. I resorted to gripping the lever with a pliers to manipulate it, after nicking some skin on the blade teeth. But, on the softer side, RIDGID provides a nice complement of overmolds on the miter gauge handle and blade height handwheel knob.
Kobalt’s KT1015 Table Saw features value pricing with a decent rolling stand. We initially had questions about its dual-locking fence, but found that it actually worked quite well. There’s plenty of wobble in it, but if you follow our Pro Tip on adjustments in the fences section, you can lock the front end in square then stabilize it with the back lock.
Hello, Thank you for your comment. We apologize for any issues our Top Table Saws of 2018 blog post has caused. It was not written to be a comparative review of the different saws but a list of the top saws that we are currently selling. It would be unfair to compare performance of a portable jobsite table saw to a industrial cabinet saw and then also compare them on price. If you would like to read a very good comparative post we suggest you check out ProToolReviews.com. They are not tied to any manufacturers and have a very unbiased opinion.
We absolutely love the Dewalt DWE7491 that we recommended as our top quality choice above. It’s a powerful, precise workhorse that can handle nearly any cutting job. However, times are changing fast, and workplace safety standards are increasing just as rapidly. If you’re a professional who wants to stay on top of your code, you should consider getting a unit that’s equipped with a flesh-detections safety system.
Finding useful reviews on this site is a challenge. A search for "table saw review" turned up a few relevant articles, but they're mixed in with news, tips, and coverage for other types of cutting tools. Most of the actual reviews for table saws are old, and many of the products are discontinued. However, we turned up a few in-depth reviews posted within the past year, as well as a few older reviews for products that are still on the market.

The JET ProShop Table Saw offers features you The JET ProShop Table Saw offers features you expect from a high-end cabinet saw in the compact design of a contactor-style machine. The transparent blade guard has independent leaves and the quick release riving knife reduces chance of kickback. A low profile riving knife is included for non-through cuts.  More + Product Details Close

Make sure you know what’s covered and what’s not, especially if you’ll be using your machine commercially (many warranties are strictly for individual, not commercial use). It’s also a good choice in this case to purchase add-on warranty coverage from a third party at the checkout. We recommend these policies for most portable table saws, since most manufacturers have either very short warranty coverage, or longer warranties which require you to foot the bill for service calls or for returning the machine to the maker.
The only dislike that I have found about the Bosch 4100-09’s operation is that unlocking the table causes a tab to pop up above the cutting surface. This tab interferes with the operation of the fence, and could lead to damage of the product. It also comes with only a one year warranty. It does have available rear out-feed extensions available, to help facilitate larger work pieces.
Under the table, you’ll find plenty of space to store away your accessories. This is valuable if you’re working on site and don’t want to keep hunting down bits and pieces. You’ll be able to stash your arbor wrench and Allen wrenches close to hand. The rip fence also flips upside down and can be stored under the table. It’s this kind of attention to detail for a jobsite saw that’s always appreciated.
Looking for a better way to take care of your wood cutting and still attain a professional result from the comfort of your home? Skil table saw with folding stand will provide exactly that. The foldable stand makes it convenient for any room use and storage. When the table saw is not in use, you can fold it right and use the space for other activities. It’s therefore suitable for small space users who are interested in professional cutting. Another interesting factor about Skil table saw, is that it cuts through materials that are 4 times the normal size. Therefore, instead of cutting each piece individually, you can set several materials to reach the height capacity for easy cutting. Additionally, the fence of this saw will guide and balance your material for accurate results. The saw also features huge blade to make the work easier and interesting for every user. If you invest in Skil saw, you will not only control your cutting but also upgrade your work to the level of expertise even if you are just starting off.
×