The first is how easy the switch is to operate. Oftentimes, you will approach your table saw with your hands full especially when we are talking about sheet goods. And sometimes you’ll be making cuts that require both hands to be occupied. Now if something goes wrong or you need to turn the saw off for any reason, you need to be able to do so and the quicker the better.
The fence on a table saw is one of its defining features and allows for precise, square, and repeatable cuts. Not all fences are equal though and a poorly built fence is a deal-breaker, in my opinion. Not only will a poorly built and implemented fence affect the quality of your cuts, but a fence that moves or is not square to the blade can cause your material to bind and kickback.
I am looking to upgrade from my first table saw which is the Ryobi that you reviewed (had to find something cheap that was decent). I do a lot of rip cuts, as well as fine precision cuts for laminating and joinery required for frames, furniture, etc. I am looking at the Skilsaw and the Dewalt 7480 and cannot decide which would be best for me. Any insight would be helpful!
post-template-default,single,single-post,postid-5859,single-format-standard,mkd-core-1.0.2,ajax_fade,page_not_loaded,,table saw theme-child-ver-1.0.0,onyx-ver-1.4.1,vertical_menu_enabled, vertical_menu_left, vertical_menu_width_290,vertical_menu_background_opacity_over_slider vertical_menu_background_opacity_over_slider_on,smooth_scroll,side_menu_slide_from_right,wpb-js-composer js-comp-ver-4.7.4,vc_responsive
To adjust blade height you simply operate the elevation wheel located on the front of the saw, and the angle of the blade can be set through a switch which is behind the wheel in case you want to make bevel cuts. The angle can be set anywhere between 0 and 45 degrees, and once you’ve adjusted the bevel angle it can be locked into place using the handle.

With a 32½" rip capacity and motor capable of up to 4800 rpm, the DWE7491RS is more than prepared to effectively deliver 3⅛" deep cuts to thick slabs of wood. Happy customers sing this machine’s praises, reporting that it’s as sturdy as a table saw can get — plus, it’s easy to use, and assembling it is a cinch. They do however note that workers looking to produce finer cuts should seek out a replacement blade since the one provided is more suited for fast, rough work.
Built on the 4100’s foundation, The Bosch REAXX exhibits similar performance with a few improvements. Despite what we’ve seen online, the REAXX did seem to have better cutting power than the 4100. (see Editor’s Note above) The narrow throat plate opening also gave it much better dust collection, allowing only the finest material to make its way out. It shares the top ranking gravity rise stand with the 4100.
The integrated blade carries an electrical signal. Once it comes in contact with human skin, the signal changes because of the skin’s conductivity and the blade immediately stop. Although some people don’t like the process of resetting the blade, it’s quite easy, and it takes only a couple of minutes. If you think about it, it’s better to hassle by resetting the blade for five or six minutes instead of losing a few fingers.

post-template-default,single,single-post,postid-5859,single-format-standard,mkd-core-1.0.2,ajax_fade,page_not_loaded,,table saw theme-child-ver-1.0.0,onyx-ver-1.4.1,vertical_menu_enabled, vertical_menu_left, vertical_menu_width_290,vertical_menu_background_opacity_over_slider vertical_menu_background_opacity_over_slider_on,smooth_scroll,side_menu_slide_from_right,wpb-js-composer js-comp-ver-4.7.4,vc_responsive
You’ll make most of your miter cuts on a miter saw. But when the material you’re cutting exceeds a miter saw’s cross-cutting capacity, you turn to your table saw miter gauge. These usually aren’t quite as precise, but some manufacturers put more thought and robustness into it than others. If you make a lot of long miter cuts, be sure to pay attention to this accessory.
I can’t tell you how many times we’ve pulled out other jobsite saws only to have accessories fall off, or require off-tool storage. Bosch designed the GTS1031, however, to securely hold all of its accessories, even including the arbor wrenches (both of them) and an allen wrench for adjusting the riving knife and dust ejection points among other things. Our favorite was the rip fence, which simply flipped upside down and stored underneath the table – clever! About the most difficult adjustment was the riving knife, which is a tool-less maneuver, but one which requires you to stick your hand way into the blade cavity to reach the release lever. When making any adjustments to the blade, it goes without saying (but we’ll say it anyway) to disconnect power to the saw as a precaution.
In terms of size, the table height from floor measures thirty four inches, with extension it measures twenty seven by forty inches and overall dimensions are 62 by 41 by 40 inches (LWH). This is simply an amazing saw and not only will you use it for many years to come, but it’s going to help you get the professional results you’re looking for in any project.
From there, the rest of the saws created a top tier of cutting power that wasn’t mind-blowingly better, but definitely noticeable. It took many cuts back and forth between saws to determine which came out ahead of other because they are so close to each other. Bosch’s REAXX took third place overall with SawStop ever so slightly ahead. Part of that simply came down to the fact that SawStop was a little bit smoother cutting. Coming out on top was Ridgid. There was noticeable vibration compared to Bosch and SawStop here, but it was able to muscle through each cut a little bit better than the other two.
TBB used an iGauging 35-125-4 digital dial indicator to measure the accuracy of the blade position to the table miter slot. This instrument has an accuracy of .0005 inches. As part of the table saw set-up, TBB installed a new Diablo blade in each saw and these never-before-used blades were used in the measurement test. To ensure that any wobble in the blade did not enter into the test results, TBB marked a single tooth as the reference point for the measurement. The blade position was moved to the front of the saw to allow the iGauging dial indicator to hit the tooth immediately behind the carbide tooth, The iGauging dial indicator was calibrated and the indicator had a reading of zero.

With a 32½" rip capacity and motor capable of up to 4800 rpm, the DWE7491RS is more than prepared to effectively deliver 3⅛" deep cuts to thick slabs of wood. Happy customers sing this machine’s praises, reporting that it’s as sturdy as a table saw can get — plus, it’s easy to use, and assembling it is a cinch. They do however note that workers looking to produce finer cuts should seek out a replacement blade since the one provided is more suited for fast, rough work.
×