Editor’s Note: If you’re using the Bosch REAXX saw without dust collection, you’re going to want to partially open up the clasp located on the bottom of the saw. This allows the sawdust to exit the blade chamber through a half-inch gap. Failure to do this will clog the output port in a very short amount of time. When you use a dust extractor you can keep this chamber fully closed.
It has a smart fence design that allows for a wide rip capacity in a small package. The Dewalt’s rails telescope, which allows them to extend further than the competition without adding to the machine’s packable footprint. That means you can make rips at up to 20 inches without needing any extensions or other accessories. The rack and pinion system allows you to set a precise fence setting without wobble, even on a flexible rail. It locks at both the front and back, to make absolutely sure you’re getting an accurate rip every time.

With a single cast iron trunnion system, the Delta UNISAW offers dependable accuracy, smooth and continuous operation, but also vibration free control. Thanks to the fact that it features a fifty-two inch fence system, it’s the perfect choice for woodworking pros, but also people who are just starting out in the woodworking industry, such as hobbyists. Since it also comes with an upfront bevel dial to easily fine tune the blade level, you get a striking accuracy within a quarter of a degree, ensuring precision setups cut after cut.

We spent a lot of time setting up and taking down the saws to see how well the stands worked and how easy it was to install and remove the blade guard and anti-kickback pawls. Then we ran a torturous ripping test with 3-in.-thick slabs of oak to find the best table saw. And finally, we used the saws for more conventional tasks like cutting plywood and ripping framing lumber as another test to determine the best table saw.


TBB measured the accuracy of the factory-set 90 degree stop by using a Wixey WR365 digital inclinometer. This device has an accuracy of 0.1 degree. We placed the Wixey gauge on the table and calibrated the inclinometer to the table by zeroing out the gauge. After that calibration, the measurements give a result that is relative to the saw table. We moved the blade to an approximate position of 70 degrees off vertical. TBB attached the gauge to the blade and used the saw mechanism to adjust the blade incline to the point at which the blade or trunnion hit the factory-set 90 degree vertical stop and recorded the measurement. TBB ran the test twice to ensure the repeatability of the measurement. In every case, the result came out to within 0.1 degree of the prior test.
Hybrid saws will often match in terms of power but very rarely have the stability and durability of a cabinet saw, so often they work well in a home work shop where you can add extra stands etc to help. One thing to think about though is that because they won’t be as stable this can often compromise on the quality of the cuts, this is something you must think about when deciding. Read More
Cabinet models are stationary, as a rule. They’re not designed for portable use, and you should plan on keeping them in your shop for their working life. However, some models are compatible with optional wheeled bases, and these are great for folks who want to be able to move their table saw around the workshop, without sacrificing any power, build quality, or stability.
We evaluated the flatness of the table by measuring the flatness by placing the edge of a precision ground flat bar across the table and placed feeler gauges in any gaps to measure any difference between the ground bar and the table. TBB took measurements in four directions. As the operator faces the saw, we measured the flatness at the arbor from front-to-rear; we measured the left-to right flatness at the arbor; we measured the flatness from the upper left-to-lower right table corners; and, finally, we measured the upper right-to-lower left flatness between the corners.
Bosch’s REAXX and SawStop were neck and neck with near perfect cleanup at the collection point and only a slight amount of dust coming out toward the user. What did make it out was even less coarse than the other Pro level saws. Both saws have narrower throat openings for the blade that reduce the amount and size of material that can make it out. In the end, SawStop produced less top dust than Bosch did to earn the win.

The blades are categorized according to number of teeth, diameter, arbor size, kerf size, application and speed. They can also be divided by material. Regular commercial table saws are 10-inch or 12-inch. Teeth usually number from 24-80. Many blades are tipped with diamond, carbon or carbide. This lets you cut through more than just wood. You will also need to think about the tilt of the blade. They are available in left tilt or right tilt. With a left-tilting hybrid or cabinet saw, the motor cover can get in the way of the sliding table. Router table extensions don’t work well on left-tilting saws. 
That’s where we come in! As your saw experts, we’ve taken a comprehensive look at all the models on the market right now, to help you find the best table saw for your projects and your lifestyle. We compared dozens of options, drawing on our own collective experience as well as professional ratings, and reviews from buyers who spent time using these saws in their homes. We compared specs, features, reliability ratings and more, to find the absolute best options out there right now.

If you’re a professional looking for a great table saw for the worksite, you’ll love the features and performance of the DEWALT DWE7480. Equipped with the Site-Pro Modular Guarding System has a rack and pinion telescoping fence rail that will allow you to make fast, smooth and accurate adjustments. This is the perfect table saw for cutting larger shelving and trim easily. With a 15 AMP 4800 rpm motor, you will go through all types of wood, even hardwood, with ease.
If you’re a DIY enthusiast, you’ll definitely find something of interest. On the other hand, professionals can also find good pieces of information on this page. The models we’ve covered all work as advertised, and you can rest assured that they are of high quality. The only thing you need to do is determine how much money you want to spend and which type is the best suiting one for your requirements.
Though you’ll still want to wear safety gear when using this table saw, it has safety features that will keep you safe too. One of those features is an emergency stop. One touch of the bright green power button brings the motor to life, but when you lift up on the emergency stop that surrounds the power button, you can stop the motor in its tracks. This button has a convenient design that lets you hit and lift it with your leg or knee too.
The stand strays from the idea that jobsite stands need to be wheeled. We can attribute this to its light weight. While it loses points for portability, Skilsaw’s design created the most stable stand of the entire group. Another benefit to going with this simple stand design is that it is certainly responsible for dropping the price point. Skilsaw is definitely the table saw you want to go with if you’re having to move your saw in and out of a truck bed rather than being able to wheel it up in a trailer.

One drawback is because of the way the blade is stopped, you will want to have an extra blade brake on hand because once it’s used, it cannot be reused. So, if you don’t have another handy, you will have some downtime. Also, the stopping of a blade moving at thousands of RPM can understandably be very hard on the blade itself. Often, the blade may need to be replaced after it has been stopped in this way. Still better than losing a thumb.
A magnetic switch is also good from a safety standpoint but may not be necessary on these smaller versions. A magnetic switch prevents the saw from starting back up if it loses power during a power outage. Basically, the power outage will turn off the saw. This is good because if for some reason the power were to come back on when you were not near the machine, the material could be shot out of it or damage the saw.
Install new blade- With the new blade, face the teeth of so they are pointing to the front of the saw table. Place the blade on the housing. Secure the new blade with the washer and nut with the use of a wrench. Make sure you are turning the wrench in a clockwise motion. Use the small piece of wood to secure the blade in place while you are securing it.
Measuring in at 19.9" x 23.4" x 13.4", the SPT70WT-01 is compact enough to fit into any aspiring handyman’s garage, but powerful enough to tackle anything you throw at it on the job site, meaning it’s an ideal entry-level table saw for the amateur hoping to turn his hobby into a career. Sturdiness, durability, and anti-kickback technology make the world’s first worm drive table saw a revolutionary machine. Satisfied buyers can’t get enough of this balanced wood-devouring behemoth.
While a lot of other Dewalt saws let us down in the dust compartment, the company have made big strides with this model. It has an internal canvas housing around the blade chamber, which keeps dust from spraying around inside the machine, without having the limitations of a rigid shield. It’s not perfect, but it does much better than the Bosch or the cheaper Dewalt.

Plus, the machined aluminum table is our favorite on the market right now. It also has a smarter motor system than either of the Dewalt’s, thanks to a soft start and automatic speed control to ensure smooth cuts. However, it’s the slowest of the pack, and it doesn’t have quite as good a fence as the yellow competition. We think it’s a great choice for pros who are concerned about accuracy, but can’t spend lots of money on their unit.
The first thing you should do before starting up your unit is to check whether you’re wearing all the necessary safety equipment. Gloves are something not many people like to wear. Apart from keeping your fingers safe, they also offer protection against thorns. As you may assume, you’ll work with a lot of thorns flying around. However, gloves aren’t mandatory, and they won’t offer much protection apart from occasional thorns.

The large cutting table surface of the Bosch 4100-09 Worksite Table Saw is roomy enough to handle large work pieces, giving you a ripping capacity of 25”. This is a really great feature if you plan to use the saw to rip solid or plywood panels, or other large materials. I use my table saw primarily for ripping sanded plywood panels for use in cabinetry, and many of my projects would be impossible with a smaller capacity saw. The rip fence glides across the saw cutting table, so you can actually use it with one hand, and locks in place for safety and accuracy. The DEWALT DW745 Job-Site Table Saw offers a 16” cut, considerably smaller than the Bosch. It is perfectly adequate for most application, such as ripping dimensional lumber and small trim applications. The type of materials and work pieces you expect to be cutting are a determining factor in your choice of table saws. If you plan on tackling any large scale projects in the future, the rip capacity of your saw is definitely a feature that you should take into consideration.


PLEASE EXCUSE THE PICTURE, LUMBER JOCKS REQUIRED ONE. I AM AWAY FROM HOME AND COULDN’t RUN OUT TO THE GARAGE TO SNAP A SHOT. I am writing a review of my Bosch saw after a few months of use. I bought this saw last November after my Ryobi saw up and died during a project. I looked at several saws in the $600-$800 range and narrowed it down to four options. The Bosch and DeWalt jobsite saws, and the Delta and Ridgid contractor saws. My requirements were in a realativly compact saw th...

Though you’ll still want to wear safety gear when using this table saw, it has safety features that will keep you safe too. One of those features is an emergency stop. One touch of the bright green power button brings the motor to life, but when you lift up on the emergency stop that surrounds the power button, you can stop the motor in its tracks. This button has a convenient design that lets you hit and lift it with your leg or knee too.

This saw/stand combination is the most expensive of the group. But you get some top-end features. The first thing you’ll notice is the stand with its splayed legs that have no wheels in the setup position. You can’t wheel it around, but man is it sturdy, which is great if you’re ripping sheets of plywood or long, heavy boards. Another unique advantage of this stand is that you can easily remove the saw. That makes the saw easy to transport and to use without the stand. But our favorite feature is the patented rack-and-pinion fence that stays perfectly parallel to the blade and is super easy to adjust. If you can afford to spend a little more, we think the DeWalt is hard to beat.
How do you tell what the best table saw is? With so many table saw choices on the market it’s hard to know which table saw is the best fit for you and your woodworking needs. Not for long. We’ve taken the leg work out by doing all the measuring, tracking, and researching for you. We’ve compiled year-over-year performance and pricing information for over 3 years to help you choose the table saw that is ideal for you and your project. Search no more, find your table saw below.
It’s highly portable. The Dewalt is available with a folding stand, which makes it extremely easy to pack up. The guard assembly lies flat, and the fence can be retracted all the way to the table to keep everything neat and tidy. It’s pretty light, too-at just 45 pounds. We also love that the adjustment tools, accessories like the miter gauge, and even the guard components can be stored inside the saw for transport, or when they’re not being used.
According to the many reviews posted online, the JET 708675PK is an excellent table saw that features a finely ground and large cast iron table that measures twenty nine by forty two inches and provides plenty of work surface for even the most demanding projects. Also, taking a closer look at the front of the blade, you’ll notice it includes ten inches of clear table which is certainly going to be appreciated by a lot of users. Looking under the table, you’ll notice a wide stance, heavy duty cast iron trunnion mechanism which provides the remarkable performance, almost vibration free operation and incredible stability the JET 708675PK is known for.
It has a smart fence design that allows for a wide rip capacity in a small package. The Dewalt’s rails telescope, which allows them to extend further than the competition without adding to the machine’s packable footprint. That means you can make rips at up to 20 inches without needing any extensions or other accessories. The rack and pinion system allows you to set a precise fence setting without wobble, even on a flexible rail. It locks at both the front and back, to make absolutely sure you’re getting an accurate rip every time.
How do you tell what the best table saw is? With so many table saw choices on the market it’s hard to know which table saw is the best fit for you and your woodworking needs. Not for long. We’ve taken the leg work out by doing all the measuring, tracking, and researching for you. We’ve compiled year-over-year performance and pricing information for over 3 years to help you choose the table saw that is ideal for you and your project. Search no more, find your table saw below.

Table saws will use one of two different kinds of drive configurations; Direct-drive motors and Belt-drive motors. In a direct-drive motor, they will link directly to the blade itself and transfer all of the power of the motor to the blade. They tend to last longer than belt drive motors and there is no belt to replace or worry about getting worn out. Belt drive motors transfer power from the motor to the blade through a belt. In this type of configuration, the motor can be offset away from the sawdust which helps the motor last longer. In general, belt drive motors need more preventative maintenance than direct-drive motors do. If you have a belt drive motor, check the tension of your belts as well as checking them for wear periodically to ensure your continued safety.
It’s not until you get a bunch of saws side by side in the shop that you start to see the difference between a $300 saw and a $500 saw. While the motors are all 15-amp, the more expensive saws have features like soft start to prolong motor and gear life, electronic feedback to maintain blade speed and gearing to maximize torque. If you look under the saws, you’ll see that the more expensive saws also have much beefier motor carriages and better-quality blade-adjusting mechanisms.
While other cabinet table saws may not offer you a clear cut every single time, that’s not the case with the SawStop ICS51230-52. This model features industrial fence system which ensures that every time you cut something, the cut is going to be very accurate and perfectly straight. One last thing to keep in mind is that the unit includes a standard base, while the mobile base and jobsite cart are sold separately.
×