TBB measured the accuracy of the factory-set 45 degree stop by using a Wixey WR365 digital inclinometer. This device has an accuracy of 0.1 degree. We placed the Wixey gauge on the table and calibrated the inclinometer to the table by zeroing out the gauge. After that calibration, the measurements shown on the gauge give a result that is relative to the saw table. We attached the gauge to the blade and used the saw mechanism to adjust the blade incline to the point at which the blade or trunnion hit the factory-set 45 degree stop and recorded the measurement. TBB ran the test twice to ensure the repeatability of the measurement. In every case, the result came out to within 0.1 degree of the prior test.
The bench table saw is the least expensive of the four types of saws. Some models come with a folding stand that is on wheels which makes it very easy to move or reposition without having to lift it all the time. Even though it is relatively light, constant lifting can become tiresome. You can mount these on your workbench which will give it more stability and could possibly reduce the amount of vibration as well. These smaller table saws generally have a 1 hp motor or even smaller and can run on a normal household circuit with no issues.
The Skilsaw SPT70WT-01 is a super high quality table saw with the power to match. The Diablo blade that comes with it will cut through 4×4 without any problems at all, like a knife through butter! One of the best features we noted was the fact that there is barely any vibration, this allows to you to cut as straight as an arrow, you can really feel the build quality with this saw.It has an extremely easy to use miter gauge, just a flick of the wrist to change the angle of cuts to exactly what you want.
Kenny Koehler An avid endurance athlete, Kenny has competed in triathlons (he's an Ironman) and various other fitness activities. Still, his passions lie with his faith, family, friends, and his love for well-designed power tools. With a background in science, you'll often find Kenny chatting up engineers at media events to get caught up on the latest tool technology.
Three professional carpenters test ten portable table saws, including two now discontinued. They outfit them all with Diablo 40-tooth general-purpose blades and test them on both 3/4-inch plywood and pressure-treated 2x pine. Each saw earns points for safety features, fence quality, stability, weight, stand design, ease of adjustment, cutting power, and dust collection. Totaling up these scores determines the saws' overall ranking, as well as their "class ranking" against comparably priced brands. Some additional single product reviews of table saws can be found elsewhere on the site as well.
I build guitars in a small shop; I need my saw to be accurate, repairable and easy to store or move. I love this saw! I use it for everything from cutting down stock to slotting my fretboards. It gets out of the way, it came dead on square, and the dust collection works pretty well with a shop vac and great with a high volume dust collector, with an Incra miter fence it makes perfect, repeatable, and accurate cuts. After I had owned it for over a year the plastic lever on the riving knife broke - I called Bosch and they "goodwilled" me a new riving knife assembly (with an upgraded metal lever) via express mail. No charge and fast, friendly service - they didn't even ask for a serial number or proof of purchase. I'd buy this saw again in a minute - all tools wear out or break at some point and I really like that the company stood behind this one and got me up and running again in a hurry. I also love all the safety features - riving knife, anti-kickback pawls, large easy-to-reach power button, nice push stick, and a dust collection port that is positioned out of the user's way.
You can store and transport the Bosch upright or on either of its sides. In between our tests, we found that the saw neatly stored away on its side on a workbench shelf. On the other hand, the DeWalt can only be stored or transported in its upright position. While it may possible to rest the saw briefly on one of its sides, there is the potential to damage the power cord, plug, or the ends of the telescoping fence rails.
Setting up or taking down Craftsman’s spring-assisted stand is a six-step process, involving various release latches. It’s not intuitive like that of Bosch or RIDGID. And, once the stand is folded down, don’t lift the handles up too far when rolling the saw around, or the stand drags against the floor. A shorter woodworker might find this less of a problem than this 6′ 3″ tester did. I also found that the stand’s narrow stance and light weight couldn’t prevent it from skittering on the floor as I pushed heavy lumber across the top. A word to the wise: weigh the base down for heavy-duty work or for cutting large sheet goods.
Like the last SawStop table saw that we looked at, this one is quite heavy and provides the stability that you need when working with plywood or any other type of wood. You can use the foot pedal on the bottom to operate the saw, but you’ll also find four wheels on the bottom of the cabinet. All four of those wheels swivel in a 360-degree direction to help you move the cabinet to any location.
Each one has different power, capabilities, mobility and price points as well. If you’re not sure which type you need, we have outline some specifics on each below that will help you choose. When you begin the search for your table saw, you will need to know the answers to a few questions that will narrow down the choices for you and make choosing much easier.
You’ll make most of your miter cuts on a miter saw. But when the material you’re cutting exceeds a miter saw’s cross-cutting capacity, you turn to your table saw miter gauge. These usually aren’t quite as precise, but some manufacturers put more thought and robustness into it than others. If you make a lot of long miter cuts, be sure to pay attention to this accessory.
We used the Freud calibration plate on each of the test saws to measure runout. We removed the new Diablo blade, installed the calibration plate, and raised the trunnion to its maximum vertical adjustment. Before measuring the runout, we placed a black mark on the calibration plate to give a consistent starting position for the runout test. The same iGauging dial indicator provided the test measurements, only this time, the units were set to read out in mm. TBB noticed that in the initial saws, the movements were sufficiently small to need the smaller metric units.
The quiet, 220-volt motors in these saws cut through the hardest stock, hour after hour, without bogging down. Cabinets are metal and extend to the floor for the best dust collection. The tops are cast iron, wide, and stable, which makes it easy to cut sheet goods. The trunnions are cabinet-mounted, so you get minimal vibration and maximum accuracy. They're also heavy; some weigh over 600 pounds. Once a cabinet saw's in place, that's where it stays.
Belt drive table saw motors run on a pulley system, most of the time some power is lost through this system, but belt drive blades can cut through thicker timber and hardwoods. They can produce power of around 3 to 5HP and thanks to the motor being mounted further away from the blade with belt drive, the motor will last longer as less dust will get into the motor. One thing to consider though is that belt drive will be in general more expensive and are normally found on heavy cabinet type saws, so this must be considered when working out your budget.
It is safe to say that we live in a DIY era. Think about it. When was the last time you went on YouTube or anywhere else online and looked for something that tickled your fancy, a guide on how something is made or done, or maybe a tutorial. Indeed, we do it very often, so why should woodworking and home improvement be any different? With the prices of table saws constantly dipping and the insane number of choices on the market, you can get one for yourself and save thousands of dollars by doing things yourself instead of hiring contractors.
This saw/stand combination is the most expensive of the group. But you get some top-end features. The first thing you’ll notice is the stand with its splayed legs that have no wheels in the setup position. You can’t wheel it around, but man is it sturdy, which is great if you’re ripping sheets of plywood or long, heavy boards. Another unique advantage of this stand is that you can easily remove the saw. That makes the saw easy to transport and to use without the stand. But our favorite feature is the patented rack-and-pinion fence that stays perfectly parallel to the blade and is super easy to adjust. If you can afford to spend a little more, we think the DeWalt is hard to beat.
If you work with wood in any capacity, chances are you rely on a table saw to make clean, accurate cuts. But when your good old saw goes to the big toolshed in the sky, it’s time to opt for a replacement. Before you dish out your hard-earned money on the first model you come across, remember that a table saw is a big investment, so it’s in your best interest to look into the many technical specifications of each option before you settle on a final purchase.
You should test the cutting depth of a saw when it is not cutting a bevel. This aspect helps in determining accurate and maximum cutting at 0 degrees. In considering bevel cutting, you should ensure the base plate is adjustable. Look out for adjustment allowance that your saw offers you such as 45, 50 or 90 degrees. The table saw should also be a feature with the flush housing so as to allow the table saw to cut very close to the edge of the wall. It is necessary to look out for this feature as will allow you to cut flooring to size at ease
If you want to take the saw with you and use it in a different location, you can purchase the optional MB-PCS-000 integrated mobile base which features 2 stationary casters and 2 pivoting casters. Furthermore, it’s also possible to upgrade the mobile base assembly to a one thousand pound lift capacity, add a hydraulic piston lift and 4 independent pivoting casters.
It’s tough to be completely objective when choosing the best portable jobsite table saw since the stock blades vary so widely. Skilsaw comes with a 30-tooth Diablo blade and Makita’s stock 32-tooth blade are both excellent while others could use some help. To make this shootout about the saws and not the blades, we turned to Diablo to outfit each saw with the same accessory.
rarely have to work with stock that thick. I mostly prefer to do this on my bandsaw any way. The 2" dust port allows me to hook up the shop vac and it does a decent job of getting most of the dust. The saw doesn't have much room in front of the blade so it was impossible to use my shop made cutoff sled. I solved this problem by making my own removable infeed extension table. Now I can use the 22" cutoff sled. After a year and a half the saw is still in adjustment and runs true. The saw stays in my shop and doesn't get bounce around on the back of a pickup truck. Based on my experience I highly recommend this saw if you have a small shop and don't plan on building large pieces
Bigger tables offer more potential for additional extensions. For example, if you’re planning to process a massive piece of wood but you cannot cut it in smaller pieces; a table extension will definitely come in handy. There are a lot of commercial add-ons you can choose from, but you can also construct one yourself if you’re experienced enough. Experimenting with these things never gets old or boring, but keep safety in mind at all times. Make sure it’s completely safe to use the said extension and pay special attention to the amount of vibrations and the overall integrity of the table after you’ve installed the add-on.
If you’re going to be transporting your unit regularly, you should aim to keep weight to a minimum. Look for something lightweight, with convenient carrying handles, or a stand that can be wheeled around dolly-style at the worksite. Conversely, if you’re only going to be using your portable saw occasionally, you can probably stand a bit more weight.
The design is not bad. The height of this particular table saw is around 35 inches. While some people don’t mind it, we think it could have been designed better. However, the best thing about the design is the fact that you can get both contractor and cabinet style table saws in one unit. Dust control is well-designed. The large 4-inch dust port offers a no-hassle setup, especially with vacuums of lower quality. In simpler words, you don’t need to purchase a super-expensive vacuum for this particular unit; any affordable one should do the job well.