The dual extension tables (rear and side) offer 50% more table space than most rectangular units. We also appreciate that Grizzly have put all the space under the worktop to use, with steel-frame shelving built in as standard. You can use it for scrap wood, tools, and accessories: you can even fit a full tool chest under there! It’s a good space-saving touch for busy shops.
Below we’ve included the current pricing (at the time of publishing this article). Pricing includes the cost of the stand and ranges from a low of $349 for the Hitachi to a high of $1,299 for the SawStop. The lowest price isn’t always the best in our opinion, we’re looking for the best value.  The Hitachi is an incredible deal at $349 and our top pick for price and value for a saw that has lots of power, a rack & pinion fence, and a solid stand.
Among the features that set this table saw apart from other competitors is the SquareLock Rip Fence. It is fabricated out of machined aluminum, slides up and down the rail without a hitch, and fixing positions couldn’t be easier. It’s probably the best fence I’ve seen in portable table saws, it feels very solid and is incredibly accurate and precise.
The saw itself is remarkably compact, measuring just 22.5″ square and a little over a foot in height (13″ to be more precise). With a steel “roll cage” that encloses the 4 HP 15-amp motor and a rubber handle that is positioned in the center of the right side of the saw, this is a tool that you’ll find very easy to toss into the back of a pickup or work van and take to any jobsite. When you carry it deck-inward, the weight of the saw presses in slightly against your leg – which actually steadies the saw somewhat, making it more manageable, though at 52-pounds let’s not go so far as to call this saw a breeze to carry. The Bosch GTS1031 included cord wrap, and the simple design of the frame also makes it easy to store up against a wall inside your shop when not in use. This isn’t a tool that really gets in the way much – it’s out of sight until it’s needed.
Todd Fratzel is the Editor of Tool Box Buzz and the President of Front Steps Media, LLC, a web based media company focused on the Home Improvement and Construction Industry.He is also the Principal Engineer for United Construction Corp., located in Newport, NH. In his capacity at United he oversees the Residential and Commercial Building Division along with all Design-Build projects.He is also the editor of Home Construction & Improvement.

Safety is a prime concern for Bosch. From the SquareLock Rip Fence through to the patented SmartGuard System to lessen any chance of kickback, your security and comfort is taken care of. The blade guard and riving knife are quick-release. This takes away any excuse for not putting the guard back in place because it would be too much trouble, something that’s an accident waiting to happen.


Measuring 30.31" x 17.32" x 41.81", this powerhouse boasts a heavy duty 10" blade that can cut up to 4" x 4" of material in a single pass. For the handyman who likes to keep all of his tools within arm’s length, RIDGID’s table saw comes with convenient onboard storage so swapping out blades or accessing your tools is just a short reach away. Buyers are crazy for this table saw, and they report that it easily fits into the corner of their garages. Plus, quick and easy assembly means you can get to work straight out the gate.

I recently brought the Ryobi RTS21G after my dwe745 got stolen and actually couldn’t believe the quality! You guys were definitely right about using the Diablo blade, makes a big difference as it’s not the most powerful table saw in the world, but really didn’t expect much for $200 but i was very surprised. Anyway just wanted to say thanks for the great review and recommendation!
A dedicated writer and communications professional spending his days lost in the intricacies of both proposal and freelance writing. When not sharing the knowledge of both fully and self-insured medical benefits to employer groups of all industries within California, Jeff Newburgh can be found at home spending time with his family and 3 dogs, pondering the next chew toy to be thrown, while kicking back and relaxing with a nice glass of red wine.

The accuracy and safety of any given saw is dependent upon the blade being parallel to the rip fence. Since we tested the amount of difference in parallelism between the saw blade and the miter slot in the previous test, we need only to see if the miter slot is parallel to the rip fence to see if the saw has a parallel relationship between the blade and the rip fence.

The frame is also improved. Instead of the basic roll-cage on the Dewalt, this one neatens things up with an integrated sub-base. It’s a rugged rubber-like pad which serves as a bumper between the main frame and your truck bed or worksite table. Both the table and the sub base are joined to the main frame, and they provide strength at both ends of the design. As with the Dewalt, you can store your tools and accessories inside, an on hooks outside the Bosch.
If you’re looking for a machine with high capacity, the SKIL 3410-02 has a 3.5-inch cut height with the ability to cut through four times the material on each pass. The consensus among reviewers is that, for such a low price, you end up compromising on miter gauge and saw blade quality. Luckily both of those things can be replaced if you so choose.  
The cabinet itself is 19-3/8-inches deep by 19-3/8-inches wide, which makes it the same size as the last SawStop model we looked at on our list of the best products. Included with this cabinet is a 20-inch by 27-inch cast iron table that extends out from the cabinet. This table is durable enough for regular use and will give you more space for working.
When I moved to a new home my shop area was radically downsized to half of a two car garage. In my former shop I had a 10" contractor's table saw for over 30 years. I really loved that saw but knew I was going to have to get a smaller saw. I reluctantly purchased the Bosch 4100-09 10" jobsite saw not expecting much. Wow was I wrong. I've had the saw for about a year and a half and use it daily to build medium to smaller sized projects ( boxes, trays, hanging cabinets, end tables). Right out of the box the saw performed well, I had my doubts about doing fine cabinet and furniture work but it is up to the task. I added the TS1002 outside table which is a necessity for larger boards. I also purchased the TS 1007 dado insert. The saw accommodates my freud 8" dado stack up to 1/2" which is sufficient for me. I use only thin kerf blades with a stabilizer and I've had no trouble ripping up to 1 1/2" hardwood. I do have to take it slower than on my contractor's saw but I

Table saws are versatile enough to earn a spot in every home shop—even if that shop shares the garage with the family car. The market offers a range of saws, from $200 portable, less accurate saws to heavy and very accurate cabinet saws costing thousands. All the table saws shown here have 10-inch blades that can cut though stock up to 3 inches thick, and they meet the Underwriters Laboratories' safety standards to prevent kickback. Keep reading for an extensive roundup of table saws, from portables to hybrid models.
As far as performance, the fence could be a bit better in its locking in – square front to rear – but you get used to being able to set it square and use the rear adjustment knob so that it stays put. Some folks have complained about motor burn outs – but having experience now with 17 saws – over 6 years or more – I haven’t encountered the problem (maybe we’ve been lucky?)
With both saws offering easy bevel and blade height adjustment, the ease of use comparison focuses mainly on the rip fences. Once the Bosch's rip fence is attached to the table, it moves smoothly across the table when unlocked. But unlocking the fence requires a bit of hand muscle. You can adjust the clamping pressure to alleviate this, but make it too loose and the fence may wobble out of square. Modifying the fence locking lever, or using a cheater bar (such as a push stick) works reasonably well.
Dust collection can seem like an afterthought for jobsite table saws. The fact that you’re outside, often on an unoccupied site, negates the need to collect your dust. But breathing that stuff doesn’t do your lungs any favors. That’s why dust collection is so important. Of course, if you’re working inside or in an occupied structure, collecting all that dust will make the cleanup part of your day easier to deal with. Since we’re not talking about concrete dust regulations, even a standard shop vac will be a good bet to help contain the mess.

In other words, a malfunction might mean an injury. This distinction could not be more pronounced in any other job site equipment than a table saw. I have personally witnessed devastating injuries on a number of occasions that could have easily been avoided by the use of safety equipment that comes standard on most brand name saws. Liability for a job site injury can be a serious setback for well established companies, but for small, independent contractors it could mean the difference between business and bankruptcy.
While other cabinet table saws may not offer you a clear cut every single time, that’s not the case with the SawStop ICS51230-52. This model features industrial fence system which ensures that every time you cut something, the cut is going to be very accurate and perfectly straight. One last thing to keep in mind is that the unit includes a standard base, while the mobile base and jobsite cart are sold separately.
×