While a lot of other Dewalt saws let us down in the dust compartment, the company have made big strides with this model. It has an internal canvas housing around the blade chamber, which keeps dust from spraying around inside the machine, without having the limitations of a rigid shield. It’s not perfect, but it does much better than the Bosch or the cheaper Dewalt.

In addition, a top-quality fence should move smoothly and have a scale that’s accurate and easy to read. Our favorite is the DeWalt fence. The rack-and-pinion system keeps the fence parallel to the blade, and the micro-adjusting knob allows easy and precise fence positioning. Runners-up in this category for best table saw are the Ridgid and Bosch saws. They both have superb fences, with the added advantage of T-slots for attaching accessories like featherboards.
This “review” is a giant nothingBurger. There is not one scrap of objective comparison between these saws. Because you sell them, they’re all great and will all zip right through “the hardest woods”. Bulll$hit. You did not test, compare, analyze, or use ANY of these saws. Re-hashinf manufacturer specs is a “Roundup” but it certainly is not a review. Typical sales pablum.
This “review” is a giant nothingBurger. There is not one scrap of objective comparison between these saws. Because you sell them, they’re all great and will all zip right through “the hardest woods”. Bulll$hit. You did not test, compare, analyze, or use ANY of these saws. Re-hashinf manufacturer specs is a “Roundup” but it certainly is not a review. Typical sales pablum.
The DEWALT DW745, due to its smaller size, does not have the capacity to use a stack of dado blades (blades designed to be stacked together to make wider cuts, grooves, and notches). It has also been noted that the plastic miter handle is a weak point, and it limits accuracy. There are no available table extensions. It does, however, come with a three year manufacturer’s warranty.
We evaluated the flatness of the table by measuring the flatness by placing the edge of a precision ground flat bar across the table and placed feeler gauges in any gaps to measure any difference between the ground bar and the table. TBB took measurements in four directions. As the operator faces the saw, we measured the flatness at the arbor from front-to-rear; we measured the left-to right flatness at the arbor; we measured the flatness from the upper left-to-lower right table corners; and, finally, we measured the upper right-to-lower left flatness between the corners.
There are several types of table saws. The types of jobs or projects you plan to use a table saw for will determine which type you buy. If you want a saw you can take from job site to job site and store it easily, then you will need a table saw that is made to be portable so that it can be easily transported to the job site. Of the portable or work site table saws on the market today, the Bosch 4100-09 10-Inch Worksite Table Saw with Gravity-Rise Stand and the DEWALT DW745 10-Inch Compact Job-Site Table Saw with 16-Inch Max Rip Capacity are two of the most popular.
Next, the rip fence is pretty hard to adjust also, and mine had a few thousandths of a bow, but that bow is way within industry standard for a portable saw. Here's what you do: First, check it for parallel, you might get lucky. (On a side note, there is a fine line between how tight to set the locking arm adjustment screw with this rip fence. Too tight, and when you lock it, you'll loose the self-adjustment feature, too loose isn't good either. Adjust the screw (on the rear of the fence), to where the fence self aligns while still getting tight) If you are like me, mine was 15 thousandths out, then unlock the locking handle and loosen the two screws on top closest to you in THIS ORDER! Loosen the screw closest to the lock handle first, and for a few turns. Next, loosen the screw that is about 6 inches away toward the middle just enough to where the fence will rotate on this screw, but not so much as to be sloppy. Begin experimenting. Pivot the fence back and forth, running your measuring device up and down the fence until you get pretty close. Lock handle and checking for parallel. Again and again. When you finally get pretty close to parallel, then lock the lever and experiment with locking both screws. If it doesn't move and you are within a few thousandths, then voila, you are done with adjusting the blade and rip fence for parallel. The other adjustments are straight forward, and once set up, THIS IS A GREAT SAW!!!!!!!!!!!!!! Good luck, hope this review helps
You want to rip down lumber with your table saw. For this you’ll need a fence. You just can’t make an accurate rip cut without one. Check the fence sits on the rails firmly. You should be able to adjust it easily in both directions. A T-square fence is the most common type. Made from welded steel, it’s precise, user-friendly and durable. Some fences are mounted with bolts. Others are welded onto the head of the T-square. Miter gauges are priceless for making cross-cuts and other more advanced cuts. This gauge acts as a guiding device. It moves in the miter slot. You can angle between 45 degrees and -45 degrees. For angled or square cross-cuts or other specialty cuts, a miter gauge fully delivers.
If height adjustments were standardized, we could expect each saw to make them nearly identically. Taking a look under the hood, we discovered several different methods—each with their own effect. Most of the saws employ a bevel gear system that provides smooth and reliable performance. We noticed that many used solid metal gearing, but Bosch used plastic for both the 4100 and the REAXX.

Product reviews on this site contain our opinion of a product or service. We will always strive for objectivity and transparency in our reviews. Our goal is to provide readers with honest, objective information based on our own experiences. We never have and never will accept payment in exchange for a positive review. Many of the products that we review are provided to us for free by a manufacturer or retailer. In some cases, we also have advertising or affiliate relationships with manufacturers and retailers of products and services we review. For additional information please visit our additional disclosure policies.

Speaking of safety, this particular model offers a satisfactory level of it. First of all, the tool-free adjustments come in handy if you’re in a middle of a project. In case you need to make a quick adjustment, you don’t have to stop whatever you’re doing and commit your attention to fine-tuning. Instead, you can do it on the go, without any additional tools. Furthermore, the convenient guarding system keeps your fingers and hands safe at all times. Don’t forget to wear protective gear; it can make a difference between life and death.
For benchtop and jobsite saws with direct drive motors, the motor RPM is the blade RPM. If you’re considering a contractor or cabinet saw, it’s a different story. In any event, Pro table saw RPMs generally range from 4000 – 5000. Don’t let numbers on the lower side dissuade you. There’s a limit to how much power you can draw and each manufacturer has to decide how they’ll channel it between blade speed and torque. So higher isn’t necessarily better.
Ridgid seems to get mixed reviews from users, maybe due to its lower price point, but continues to impress us in head to head competitions. With this edition, Ridgid’s 15 amp motor powered through cuts better than any other saw we tested. Sure it was close, but it consistently beat out each competitor. That power does come with more vibration than some of the others though.
Last but not least, you need to pay attention to the dust collecting capabilities of a particular model. Portable units usually have a weak dust-collecting capacity, but they aren’t foreseen for large projects. However, all other types do feature some kind of dust collecting system. The first thing you should check is the diameter of the dust port. The larger it is, the less debris you’ll have flying around. Also, check out the vacuum requirements because some models work only with super-expensive vacuums. As you can assume, the thing that’s lacking with those models is cost efficiency. However, if you don’t have budget limitations, feel free to invest in a high-end vacuum, it makes a huge difference.
Plus, it’s simply a great table saw in its own right. It’s powerful, efficient, and quiet. It cuts through all kinds of stock smoothly and easily, and the dust collection system helps it clean up after itself. Previous buyers who upgraded to this one said that the transition from their old cabinet units felt like switching from a family sedan to a sports car. We recommend it to anyone looking for the absolute best quality, for small to midsize pro shop work or the passionate home woodworker.
If you’re going to have a quality product, you need a fence system that’s perfectly square to the table so your cut is perfectly parallel to the edge. Obviously, framers have a bit more leeway than jobsite carpenters and there’s plenty of variance in fence quality. Cheaper saws have fences that can easily move out of square as they slide along the surface of the table. Avoid these if you want quality results. The fence system needs to be easy to keep square to the blade.
We don’t always post the point totals when we do a shootout like this because it gets complicated – you have to decide what the important features and performance categories are, determine how much weight each one should hold, and then actually hash out the scores with the team. That said, some of these table saws scored so close to each other that I didn’t feel it was fair to just leave it up to the rankings.
When you’re setting up your table saw fence, slide it into position by pressing the front of the fence forward against the table with both hands. This will allow the entire fence to slide square to the table. Hold your final position with one hand while locking it down with the other. This should help you avoid many of the accuracy issues that come from an off-square fence.
Makita joins DeWalt with an external riving knife release so you don’t have to reach into the throat to loosen it. We actually ran into an issue with the design because of a slightly bent plate holding the knife in place. That aside, the intent of the design is sound and should make for an an easier experience. Because of the external release, Makita screws down the throat plate in place. You should only need to get in there for blade changes if everything functions properly.
As mentioned, the look is similar to a hybrid with a full enclosure. Looks can be deceptive, though… The core design purpose is for this saw to stand up to constant heavy use in a commercial setting. This is not a tool you buy for casual woodworking at home.These bulky, heavy units are built to last the distance. They can weigh up to 500 pounds. You’ll get an accuracy and rigidity not available in lesser types of table saw.Other table saws call for regular adjustments. With a cabinet saw, you won’t need to do this as often once it’s set up properly. 240V motors developing 3-5HP mean there’s very little the best cabinet table saw won’t rip through with ease. Large sheets of hardwood are no problem at all.

IMPORTANT REVIEW UPDATE (10/4/2016): After doing some additional testing with pressure-treated lumber and heavier stock, we [initially] found some issues with the Bosch REAXX saw that we couldn’t explain—except to say that it didn’t have the power we expected for cutting through denser wood. The blade exhibited a significant drop in speed during many common ripping cuts, and it even stalled out entirely at other times. We contacted Bosch and worked directly with them to determine the nature of the issue (which appeared to have to do with the saw’s electronic speed control). Here is the initial statement from Bosch on the matter:
It’s easy to use, quite safe, and most importantly – it’s a high-quality piece of equipment for a more than reasonable price. If you don’t like what you see, don’t hesitate to read some of our other reviews, there might be something of interest for you. As far as this particular model goes, it should turn out to be a worthy and cost-efficient investment. In the end, it all comes down to your personal preferences.
While a miter saw is indispensable, having a great table saw is a wonderful way to broaden the scope of your woodworking. Whether you want miters or bevels, rips or compound cuts, the best table saw is a highly versatile woodworking equipment. Not only can you perform a healthy range of different cuts, you can also hook up various accessories to your table saw. Table saws are truly multi-purpose in the workshop.
Now, don’t get me wrong, there are other portable table saws that are lighter than Bosch’s GTS1031 (who’s name sounds like a cross between a fast production car and a tax document). The key with the Bosch is that it’s jobsite tough. Give the other saws some wet lumber or run them all day long and you’ll smoke the motor, bog them down, or send them off a second story porch in frustration. Bosch seems to have designed the GTS1031 with two things in mind: portability and power. Portability, because all of the accessories store right on-board, and they do so securely, so they won’t fall out, even if the saw is bumped and tossed around – as jobsite saws tend to be.
Cabinet saws are the prime choice for professional woodworkers. A more powerful induction motor, usually 3 to 5 HP, is enclosed in a cabinet, as part of a super-sturdy overall construction. This type of table saw is ideal for making smooth, straight cuts through hardwoods without worrying about excessive vibration. All that power and stability comes at a price, though. Low-end cabinet saws start around $2,300 and can go past $5,000 for industrial table saws.
Some previous buyers had motor trouble. Their units conked out early, or worked inconsistently. Apparently, that was down to cheap internal bearings used in the first few iterations of the Bosch. However, according to company replies to some reviewers who cited the issue, the problem has been addressed in the last few versions of this model. We’ve also found that reviews from the past few years are much more consistently positive.
The design is quite good. The SawStop safety system ensures smooth and flawless operation while protecting you from a variety of hazards. However, regardless of the safety aspects, you should always wear protective equipment, especially gloves and goggles. One of the most notable things about the design is the fact that it provides 99 percent dust collection both below and above the table. The riving knife maximizes kickback and also offers protection.
Our table saw review quickly showed that today’s portable table saws are light-years ahead of the small-saw offerings from a decade ago. They feature big-capacity cutting, greatly improved safety features and attached stands for easy setup. And saws in the upper price range rival stationary saws in accuracy and quality of cut. We limited our review to saws that included a stand with wheels and ones that could rip at least 24 in. wide, only the best table saw for our readers!
Hybrid table saws are the latest thing on the market these days. They’re in between contractor and cabinet table saws in terms of price, power, and precision. These have either half-cabinets or cutaway stands like a contractor saw, but with the super-powerful motor and improved stability of a cabinet unit. They’re heavy, so you should be prepared to use them on a wheeled lift, but they can be transported fairly easily if you have helpers.
There are a few nice conveniences which we don’t always see on affordable units like this. The Grizzly has a built-in miter guide, made from cast iron, which slides easily in the worktop. The left-tilting blade is coordinated with a digital display, which gives you an accurate, real-time readout on your bevel angle as you cut! The motor has a starting amperage of 13, which is safer for your breakers than 15 amp models. There’s a standard 4” dust collection port, and

Setting up or taking down Craftsman’s spring-assisted stand is a six-step process, involving various release latches. It’s not intuitive like that of Bosch or RIDGID. And, once the stand is folded down, don’t lift the handles up too far when rolling the saw around, or the stand drags against the floor. A shorter woodworker might find this less of a problem than this 6′ 3″ tester did. I also found that the stand’s narrow stance and light weight couldn’t prevent it from skittering on the floor as I pushed heavy lumber across the top. A word to the wise: weigh the base down for heavy-duty work or for cutting large sheet goods.

On the downside, these units are by far the heaviest type of saw, and they’re the most expensive by a long shot. Their cast iron worktops and steel cabinets makes them more of a permanent fixture than nearly any other tool. To move them around your shop, you’ll need an expensive, heavy-duty wheeled base, which can cost even more money up front. They’re best for people who will keep them in one place, and use them on a regular basis.
Compared to some of the other miter saws we’ve used – predating the new riving knife requirement, the Bosch GTS1031 guard system is much easier to install and remove when necessary (and to put the saw back into portable mode). We timed ourselves and assembled and tore down the saw in just over 2 minutes – and we were confident that our time would get better with more practice. The table is made of machined cast aluminum and is texture-coated to make it fairly slick – something that really helped when cutting larger pieces of 3/4″ plywood for a workbench surface. As for extending the table – that was super-easy. You just lift the table extension handle upwards and slide the table to the right. This gives you a full 18″ of rip width to the rip fence with your material to the right of the blade. Collapsed, you get up to 10″. Motion of the rip fence and the table extension were smooth. While the fence had some wobble in it at the far end – this completely disappeared when you locked it down – and the shape of the rear of the fence locked it straight every time. It’s a good system and more than adequate for a low-cost portable saw like this. We’ve seen more robust fence systems. But typically the trade-off has been in weight as well as cost.

SawStop PCS31230-TGP252 10 in. 3HP table saw is a high performance cabinet table saw that features a durable cast iron table, 44 x 27 in. of total space, and is super durable, making it an ideal table saw for professionals. In addition to its industrial capabilities, this SawStop table saw also boasts a couple other practical features including a Flesh Sensing Technology, dissipative arbor belt to prevent hazardous charges, and an easy-to-change brake cartridge.
Using the guards the saw came with is crucial for the safety of your hands. If you are working with smaller pieces, make or buy a sled with a work clamp so that you can maintain a safe distance from the blade. The clamped sled can be as simple as a piece of plywood with a track on the bottom that’s responsible for riding in the groove. It’s quite simple to construct, saves time, and most importantly – fingers.
For homeowners without the luxury of a huge garage to fit their enormous table saw, DEWALT’s DWE7480 is a compact alternative to bulkier machines with the same wood slicing power. Measuring 25.8" x 26.5" x 13.9", the DWE7480 hosts a 15-amp motor that cuts at an unbelievable 4800 rpm with a ten-inch blade, meaning this small package packs big performance — and with adjustable rear feet that are designed to allow users to level their table saw on uneven surfaces, you’ll be sure to get a clean, precise cut every time, no matter how rugged the terrain. An additional dust port makes collecting your sawdust a breeze — especially if you attach an optional shop vac extension.
Safety is a prime concern for Bosch. From the SquareLock Rip Fence through to the patented SmartGuard System to lessen any chance of kickback, your security and comfort is taken care of. The blade guard and riving knife are quick-release. This takes away any excuse for not putting the guard back in place because it would be too much trouble, something that’s an accident waiting to happen.

Even though the trunnion mechanism from Powermatic has been known to be the best there is, further refinements have been made to it in order to make it even better. The conically shaped worm gear drive with better surface area, the high end bearings, but also the cast iron, box style construction combine with the solid and smooth feel of the height and tilt adjustments. Thanks to the adjustable backlash, it’s very easy for users to adjust the mechanism back to the factory fresh feel and clearances.


The first thing you should do before starting up your unit is to check whether you’re wearing all the necessary safety equipment. Gloves are something not many people like to wear. Apart from keeping your fingers safe, they also offer protection against thorns. As you may assume, you’ll work with a lot of thorns flying around. However, gloves aren’t mandatory, and they won’t offer much protection apart from occasional thorns.
Make sure all the panels on the cabinet (including the motor shroud) are made from steel, and look for powder-coating on the panels to help the paintwork last. The adjustment flywheels, the fence rails, and the frame of the table assembly should be steel as well. The most important part to look at under the hood is the trunnion. The trunnion supports the motor, and you’ll want it to be made from solid cast iron. The sturdier the trunnion, the smoother your unit will cut.
All seven saws in the best table saw testing have some kind of dust control. The Rockwell saw has a completely enclosed motor compartment with a large dust bag that attaches under the saw to catch sawdust. The remaining saws have a shroud around the blade and a 2-1/2-in. port on the back for attaching either a bag or a vacuum cleaner. None were perfect, but at least you can catch most of the sawdust. The Craftsman and Ryobi also include a dust bag that attaches to the vacuum cleaner port.

Clint DeBoer When he's not remodeling part of his house or playing with the latest power tool, Clint enjoys life as a husband, father and avid reader. He has a degree in recording engineering and has been involved in multimedia and/or online publishing in one form or another for the past 21 years. In 2008, Clint was one of the founders of the Pro Tool Reviews online magazine. He hopes his efforts at PTR will provide builders and contractors with reliable and engaging tool reviews to help them make better tool purchasing decisions.


The latest advance in table saw safety is a feature that stops the spinning blade when it senses the presence of tissue, such as a finger or forearm. A company called SawStop was the first to offer this technology, and currently, it holds the exclusive right to sell saws with this feature in the United States. (Bosch introduced a portable table saw with blade-stopping technology in 2016, but was forced to take it off the market after a successful patent-infringement suit by SawStop.) In 2017, the CPSC proposed a new rule to make SawStop's technology mandatory on all table saws, but that rule is still under review. See the Buying Guide for more information.
If you’re a professional woodworker, you should expect a standard hookup on any saw. However, you’ll find that no portable table saw does a perfect job collecting sawdust. Since these aren’t enclosed tools like a cabinet saw, there are lots of ways for dust to find its way to your floor and spray around your shop. You’ll want to look for the most enclosed, effective design possible, and pair it with a vacuum system that’s got some heft.
Prices, promotions, styles, and availability may vary. Our local stores do not honor online pricing. Prices and availability of products and services are subject to change without notice. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted.
Table saws will use one of two different kinds of drive configurations; Direct-drive motors and Belt-drive motors. In a direct-drive motor, they will link directly to the blade itself and transfer all of the power of the motor to the blade. They tend to last longer than belt drive motors and there is no belt to replace or worry about getting worn out. Belt drive motors transfer power from the motor to the blade through a belt. In this type of configuration, the motor can be offset away from the sawdust which helps the motor last longer. In general, belt drive motors need more preventative maintenance than direct-drive motors do. If you have a belt drive motor, check the tension of your belts as well as checking them for wear periodically to ensure your continued safety.

Looking for a better way to take care of your wood cutting and still attain a professional result from the comfort of your home? Skil table saw with folding stand will provide exactly that. The foldable stand makes it convenient for any room use and storage. When the table saw is not in use, you can fold it right and use the space for other activities. It’s therefore suitable for small space users who are interested in professional cutting. Another interesting factor about Skil table saw, is that it cuts through materials that are 4 times the normal size. Therefore, instead of cutting each piece individually, you can set several materials to reach the height capacity for easy cutting. Additionally, the fence of this saw will guide and balance your material for accurate results. The saw also features huge blade to make the work easier and interesting for every user. If you invest in Skil saw, you will not only control your cutting but also upgrade your work to the level of expertise even if you are just starting off.
×