The quiet, 220-volt motors in these saws cut through the hardest stock, hour after hour, without bogging down. Cabinets are metal and extend to the floor for the best dust collection. The tops are cast iron, wide, and stable, which makes it easy to cut sheet goods. The trunnions are cabinet-mounted, so you get minimal vibration and maximum accuracy. They're also heavy; some weigh over 600 pounds. Once a cabinet saw's in place, that's where it stays.
The first step to take when using a table saw is to don all the appropriate safety gear that a responsible operator should use. This includes, at the bare minimum, eye protection and thick work gloves. It's also a good idea to protect your ears with ear muffs or earplugs and to consider a mask that will cover your mouth and nose to prevent the inhalation of fine saw dust particles.
Bosch engineers deserve kudos for the Gravity-Rise stand, and it’s a design some other manufacturers should emulate. Twist one lever, and the sturdy, steel frame folds up or down fluidly to convert from sawing to transport or storage. Eight-inch wheels and lugged rubber tires make this base easy to steer overland or pull up steps. Plus, the base’s stance is wide, giving it sure footing if you are pushing long planks or heavy sheet goods through. It will not tip. But, the stand when erected sets the saw’s tabletop quite high, at 38-1⁄2″. Shorter users may find this to be a bit too tall for comfort.
PLEASE EXCUSE THE PICTURE, LUMBER JOCKS REQUIRED ONE. I AM AWAY FROM HOME AND COULDN’t RUN OUT TO THE GARAGE TO SNAP A SHOT. I am writing a review of my Bosch saw after a few months of use. I bought this saw last November after my Ryobi saw up and died during a project. I looked at several saws in the $600-$800 range and narrowed it down to four options. The Bosch and DeWalt jobsite saws, and the Delta and Ridgid contractor saws. My requirements were in a realativly compact saw th...
With that said, the Dewalt DWE7491RS (another jobsite saw) has an amazing fence. It also has a greater ripping capacity – so if this additional functionality is more important to you than portability, it might be something to consider. Although keep in mind that it’s also 30lbs heavier, and the stand is much worse than that of the Bosch (which we’ll discuss later in this article).
Robert Bosch Tool Corporation is aware of questions raised about the power of its REAXX™ Jobsite Table Saw. We are taking this feedback seriously and we’re working with product and engineering teams to answer these questions. Flesh-detecting Bosch Active Response Technology™, which comes on board every REAXX Job Site Table Saw, is unrelated to the questions raised about the saw. The REAXX table saw remains one of the safest and most-advanced table saws available today. 

The Grizzly G0690 is a very unique and powerful table saw and each part of it says performance and quality. With a 3 HP, 220V, 3-phase Leeson motor, heavy cast iron trunnions, wings and table to its triple belt drive system, this model should definitely last you for a lifetime. It’s not only its impressive build quality that’s going to strike you about it, but also its other features that include a four inch dust collection port, a T-slot miter gauge, a magnetic switch, but also heavy cat hand-wheels, riving knife and camlock T-fence. If you’re a professional who’s been using cabinet tablet saws for a quite a while, you’ll immediately appreciate the quality of the Grizzly G0690.


If you’re looking for a machine with high capacity, the SKIL 3410-02 has a 3.5-inch cut height with the ability to cut through four times the material on each pass. The consensus among reviewers is that, for such a low price, you end up compromising on miter gauge and saw blade quality. Luckily both of those things can be replaced if you so choose.  

Bengt – We appreciate the feedback as it always helps us get better. Having said that I think some of your concerns were evaluated and included in the results in ways that may not be entirely clear. We adjusted each saw after checking the blade/fence measurements and had no issues getting them adjusted (I may add some text to reinforce that in the article). We don’t do long term testing in this type of article as it’s simply not feasible…so making a statement about whether the saw holds those adjustments isn’t feasible. We evaluated the fences and ranked them in the ergonomics section, we even did lateral load testing on them as part of that ranking.

Methods for tilting the blade to cut bevels vary among the saws. The Porter-Cable saw is the only one with a conventional handwheel bevel control mounted on the side of the saw. The crank gives you great control for setting an exact angle. To set the bevel on the Bosch, DeWalt and Rockwell saws, you simply release the bevel-lock lever and tilt the saw to the preferred angle. It’s easy to go quickly from a 90-degree to a 45-degree bevel with this method. The Ridgid, Craftsman and Ryobi saws have a rack-and-pinion setup. These saws utilize the front crank for setting the bevel.
The professional level saws saw a separation as well and all were well ahead of the cutting power we saw with the value group. A middle tier of cutting performance started with Makita and Bosch’s 4100 while DeWalt was significantly better. Entering the fray with the only worm drive system, we had high hopes for Skilsaw’s entry. It was solid and smooth—definitely at the Pro level— and close to what the 4100 delivered.
When the blade touches flesh, a brake will stop the blade and the blade drops down below the surface of the table. The operator will presumably leave with only a small nick or no injury at all. These systems definitely bump up the price of the saw, but it’s a major safety feature and just might be able to save you some very expensive medical bills, along with your fingers.
I really do like your site and being on Long Island there is a familiarity to the way y’all work. You are quick to respond to comments and put in a great effort but…. This review I feel you miss the mark. Out of box accuracy is important but. Ore important to a pro user is tool able to be adjusted to be near perfect and how does it hold this position. No comments on how solid the fences are, ie deflection movement, ease of micro adjust, etc. all the fancy self feed stuff etc, what saw feels the most powerful? Smoothest ? All theses kizmos are for the manufacturers to hype. Your strengths are that you actually use these machines, so your strengths are to BE MORE opinionated or biased not less because your opinion has meaning or weight. Let the know knowings use the kizmos and just give us your real opinions based on real use. Just my 2 cents.
In order to measure the blade speed we used a digital laser non-contact tachometer. A piece of reflective tape was adhered to each saw blade just behind the carbide tooth, so that the tape would be just above the top of the wood cutting surface, allowing us to capture the blade speed during the cuts. We used a power-feeder to ensure that all the material was pushed through each saw at the same feed rate. In the photo above you can see our test set-up with the power feeder, a decibel meter to the left, the digital tachometer in the center, and the amp meter on the right. If you look really closely at the saw blade, the piece of reflective tape is to the left side of the blade near the power feeder.
I am a general contractor in the Midwest. I used the saw and stand a lot for the 1 week I've had it. Overall the saw works well, dado blades are easily interchangeable, and it's surprising quiet. However, the stand base bent on me today. I had it passively mounted in the rear of my enclosed 7x16 trailer. Opened the door this morning after arriving at the job site and it had sunken over. I thought maybe it had come out of the mount I made, but sadly that was not the case.
If you are an avid hobbyist, this saw is made just for you. The company is known for its uncompromising quality and durability. This saw has a safety system where the blade stops and retracts automatically when it comes into contact with anything that is not wood.  The microblade guards keep debris from flying all over your workshop. It is easy to change between blades. You will not require a riving knife to do this. Its award-winning dust collection system ensures that you have a clean and presentable workspace at the end of the day.
With that said, the Dewalt DWE7491RS (another jobsite saw) has an amazing fence. It also has a greater ripping capacity – so if this additional functionality is more important to you than portability, it might be something to consider. Although keep in mind that it’s also 30lbs heavier, and the stand is much worse than that of the Bosch (which we’ll discuss later in this article).
One thing manufactures noticed over the years was that when people used the splitters in normal straight cuts it worked well but it’s biggest downfall came when contractors wanted to do cross cuts. What would happen is that people would remove the splitters to make the cross cuts but then forget to fixed them back in place. One brilliant table saw safety feature is the riving knife. The Riving knife is attached directly to the blade mechanism, this allows it to always be attached not matter where or what angle the blade is.
Most table saw blades come in 8, 10 or 12inchs in diameter, but you can also get a lot smaller and larger sizes if you require special cut sizes and cut depth sizes. When looking for a new blade when it comes to sizes, blades are measured in two sizes mainly, the mounting hole and the total blade diameter, make sure you take the mounting hole size in to consideration when buying a new blade as this could be something very easily over looked but could cause an issue.
One thing you must be aware of with a contractor saw is the fact that they can be a lot more difficult to move from job to job, this is something that must be considered before purchasing. For thicker and harder type woods a cabinet table saw maybe the best way to go, especially for the long-term benefits, but for the average mid-sized contractor it’s still a great option. Read More
×