The quiet, 220-volt motors in these saws cut through the hardest stock, hour after hour, without bogging down. Cabinets are metal and extend to the floor for the best dust collection. The tops are cast iron, wide, and stable, which makes it easy to cut sheet goods. The trunnions are cabinet-mounted, so you get minimal vibration and maximum accuracy. They're also heavy; some weigh over 600 pounds. Once a cabinet saw's in place, that's where it stays.

In recent years, there has been a cloud of controversy surrounding the inherent safety issues surrounding the table saw. SawStop developed a flesh detection technology that pulls the blade below the table surface 3 milliseconds after coming into contact with skin. It really created a new class of table saw that, as of June 1st, finally has some competition in the form of Bosch’s REAXX.
As far as performance, the fence could be a bit better in its locking in – square front to rear – but you get used to being able to set it square and use the rear adjustment knob so that it stays put. Some folks have complained about motor burn outs – but having experience now with 17 saws – over 6 years or more – I haven’t encountered the problem (maybe we’ve been lucky?)
Buying a table saw can cover a lot of bases. You have everything from DIY models to professional production level cabinet table saws. In this article, we’re looking what is arguably the most popular – jobsite table saws. They’re on the less expensive side and are highly portable compared to their shop counterparts. That makes them go-to tools for framers, jobsite carpenters, and Prosumers.
Under the table, you’ll find plenty of space to store away your accessories. This is valuable if you’re working on site and don’t want to keep hunting down bits and pieces. You’ll be able to stash your arbor wrench and Allen wrenches close to hand. The rip fence also flips upside down and can be stored under the table. It’s this kind of attention to detail for a jobsite saw that’s always appreciated.
Likes: Cuts extremely well and has excellent stability. Its blade guard and riving-knife assembly are locked and unlocked by a lever located conveniently along the table's left edge. A simple, separate shark-fin riving knife can be used when the guard is too big for narrow rip cuts. We appreciate the antiglare surface on the tape ruler that measures the distance from the blade to the fence.
If the blade you purchase has a .092” kerf (i.e. Irwin Marathon 80T, FreudLU83R010) you will most likely have issues with binding on the back end of the cut. To be safe, find a blade that has a kerf of around .098” (i.e. Freud Avanti TK905 50T) and this should take care of the problem. You should also take note that every blade Bosch makes should also work with the Bosch 4100-09.
Home Depot sells around 60 models of table saws on its website, and the top models get hundreds of reviews from users. We found four portable saws with ratings of 4.5 stars or better from 250 users or more, and one contractor saw gets ratings just shy of 4.5 stars overall from more than 650 owners. Individual reviews are fairly short and include ratings for quality and value.
Install new blade- With the new blade, face the teeth of so they are pointing to the front of the saw table. Place the blade on the housing. Secure the new blade with the washer and nut with the use of a wrench. Make sure you are turning the wrench in a clockwise motion. Use the small piece of wood to secure the blade in place while you are securing it.

The weak point of this rolling stand is the base where all the weight sits. I really like the Bosch rolling miter saw stand, which is what convinced me to buy this setup. When you compare the miter saw to this table saw, it's a night and day difference. The miter saw from Bosch has thicker and larger diameter metal tubing. It clearly weights more, but it's on wheels, and has yet to show any fatigue from constant use.


There were really two major performance considerations we wanted to look at to help determine the best portable jobsite table saw: cutting power and dust collection. Power is an obvious choice. We want to make clean, straight cuts, but we don’t want to spend all day making them. Any saw can be calibrated to be straight and accurate, but some have to be babied more than others to get professional results.
As with the smaller Dewalt we’ve recommended, this one has very inconsistent quality control on the table. Some reviewers cited units with bowed, funky surfaces, while others got units that were perfectly flat. that’s a flaw of the molding process. We also have a bone to pick with Dewalt as far as the coating on these. While we understand that the coating is supposed to help wood slide better, it just doesn’t seem to last very long or hold up well. It also has the same flawed warranty coverage. We’d recommend purchasing add-on coverage.
All table saws sold in the U.S. come with a riving knife, anti-kickback pawls, and a split blade guard. Because some cuts can’t be made with these safety features installed, they are removable. If you’re looking for a fun party game, see who of your uninitiated friends can install both correctly without a manual. While each one is different, their nature means you can use the saw without them installed. I’d be remiss if I didn’t tell you those cuts are more dangerous, so avoid it if you can.
One thing you’ll love about the riving knife is that it allows for adjusting the table saw without using any special tools, for non-through and through cuts including, pictures frames, grooves for shelves, but also cheek cuts for furniture, rabbets and dadoes. There’s also the possibility to store different tools or anything else you may find under the tablet board and given the fact it’s expandable and convenient, it’s going to make using the Delta 36-L552 an even more amazing experience. For dust collection, the table saw comes with a bi-level dust extraction system which offers superior dust collection capabilities.
It’s the best of the three at keeping your shop clean. The SawStop has a blade guard and arbor enclosure that’s engineered and sculpted to maximize vacuum suction at the cutting edge. Plus, the guard hugs tightly to the blade, and like the Jet, opens at each side so that whichever way you’re cutting, dust goes down the vacuum chute instead of off to the side of your workspace. It’s lab-tested to be up to 99% effective, and it’s certainly the most impressive dust collection system we’ve seen to date.
But, their price point reflects that. If you want the absolute best table saw money can buy then you can go pay $10,000 and it’s yours. We always accept a certain number of tradeoffs depending on what our budget allows So, if I am only doing a few DIY projects a year, I am not a carpenter by trade, and my budget is limited, the SKIL table saw may be right up my alley.
If height adjustments were standardized, we could expect each saw to make them nearly identically. Taking a look under the hood, we discovered several different methods—each with their own effect. Most of the saws employ a bevel gear system that provides smooth and reliable performance. We noticed that many used solid metal gearing, but Bosch used plastic for both the 4100 and the REAXX.
We’re not alone in loving the Jet’s guard system. We read lots of reviews from pros who said they’d used lots of table saws in their time, but this was the first time they didn’t absolutely hate the guard. In fact, many wrote that they started working with the guard onboard for the first time, simply because it worked so well. It’s certainly one of the most unobtrusive ones we’ve seen!
The DeWalt will do you proud for a broad spread of applications. If you’re a home woodworker, you’ll be able to rip sheet material, size material as thick as 3 inches, frame lumber and make cross cuts to your heart’s content. For professionals, the DeWalt is perfect for trim carpentry, installation of hardwood floors, decking or remodeling. There’s very little you can’t do with this beast.
It’s sturdy. This unit also has a metal roll cage frame all around, which helps it handle the rough and tumble of travelling to worksites on a regular basis. It has a locking mechanism to help it stay securely on stands. We’re also super impressed by how well-made the adjustment knobs feel on this one. Buyers reported using this one for several years with no issues.
Jet has a strong reputation for providing customers with durable power tools that operate just like professional models but cost less, and that is definitely true of this 10-inch table saw that comes with a riving knife. You’ll like the basic design of this model, which has an intuitive design that allows you to set it up and start cutting faster. It features both a solid cabinet as well as an extension table that stretches out from one end.
One thing you’ll love about the riving knife is that it allows for adjusting the table saw without using any special tools, for non-through and through cuts including, pictures frames, grooves for shelves, but also cheek cuts for furniture, rabbets and dadoes. There’s also the possibility to store different tools or anything else you may find under the tablet board and given the fact it’s expandable and convenient, it’s going to make using the Delta 36-L552 an even more amazing experience. For dust collection, the table saw comes with a bi-level dust extraction system which offers superior dust collection capabilities.
6. Clamp rip fence to check if it holds securely at front and rear. If rear is not clamped securely, un- clamp fence and turn rear clamp adjustment screw 6 clockwise for increased clamping. Try clamping the fence to verify if it self aligns and clamps tightly at the front and rear. Overtightening of the rear clamp adjustment screw 6 will cause the rip fence to be non-self aligning (Fig. 23). Overtightening may cause friction or “chatter” when fence is moved side to side.
×