When choosing the best table saw for jobsites, you’ll need a rip capacity of more than 24″. Why? 24″ is half the width of sheet material. Some models will give you as much as 35″. Since you ideally want to have the waste edge opposite the fence, the larger the capacity the better. But again, jobsite table saws are designed for Pros with a little more inherent forgiveness in the job, so the assumption is that you can cut the waste edge against the fence if necessary.
The design is not bad. The height of this particular table saw is around 35 inches. While some people don’t mind it, we think it could have been designed better. However, the best thing about the design is the fact that you can get both contractor and cabinet style table saws in one unit. Dust control is well-designed. The large 4-inch dust port offers a no-hassle setup, especially with vacuums of lower quality. In simpler words, you don’t need to purchase a super-expensive vacuum for this particular unit; any affordable one should do the job well.

With both saws offering easy bevel and blade height adjustment, the ease of use comparison focuses mainly on the rip fences. Once the Bosch's rip fence is attached to the table, it moves smoothly across the table when unlocked. But unlocking the fence requires a bit of hand muscle. You can adjust the clamping pressure to alleviate this, but make it too loose and the fence may wobble out of square. Modifying the fence locking lever, or using a cheater bar (such as a push stick) works reasonably well.


Robert Bosch Tool Corporation is aware of questions raised about the power of its REAXX™ Jobsite Table Saw. We are taking this feedback seriously and we’re working with product and engineering teams to answer these questions. Flesh-detecting Bosch Active Response Technology™, which comes on board every REAXX Job Site Table Saw, is unrelated to the questions raised about the saw. The REAXX table saw remains one of the safest and most-advanced table saws available today. 
With this saw, it was a very easy thing to plug it on and get started. The included cord is a reasonable length, but you’ll still need an extension cord unless you happen to be right next to an outlet in your workshop. Raising and lowering the blade is a smooth process and we found the mechanism to be nice and stiff, so you can be very precise with your cut depth. Only time will reveal whether or not this stays tight over the long haul, but it seems to be well-made. Mounting the accessories, like the smart guard system is quick. You just raise the riving knife using the release lever. The riving knife locks into a lower and upper position through the use of two sets of pins. In the upper position it is ready to accept the barrier guard, which you can remove from below the saw. It attaches easily with a lever lock and the anti-kickback device can then be placed on the back of the riving knife such that the teeth are set to grab any wood brought forward by the blade. The physical nature of the barrier guard assembly precludes you from placing your fingers anywhere near the cutting surface of the blade. We (and Bosch) recommend keeping this guard on the saw anytime you are doing “through” cuts. All-in-all, the table saw’s included safety features are more than adequate to keep you from encountering any unfortunate accidents. Removing them, or using the tool improperly, however, will considerably raise your level of risk.
Though you’ll still want to wear safety gear when using this table saw, it has safety features that will keep you safe too. One of those features is an emergency stop. One touch of the bright green power button brings the motor to life, but when you lift up on the emergency stop that surrounds the power button, you can stop the motor in its tracks. This button has a convenient design that lets you hit and lift it with your leg or knee too.

The type of woods you cut will determine how powerful a motor and how fast a blade speed you need from your portable table saw. If you’re going to be dealing primarily with thinner boards and softwoods, you don’t need anything hugely powerful. If you’re working with hardwoods or thicker softwood stock you should look for a more powerful motor. Likewise, if you’re only an occasional woodworker, you needn’t worry about finding a motor that won’t burn out.
It’s tough to be completely objective when choosing the best portable jobsite table saw since the stock blades vary so widely. Skilsaw comes with a 30-tooth Diablo blade and Makita’s stock 32-tooth blade are both excellent while others could use some help. To make this shootout about the saws and not the blades, we turned to Diablo to outfit each saw with the same accessory.
I definitely give this one 5 stars, but this is specific of the application – it being portable. If I was comparing it with other Hybrid saws, than this one doesn’t really compare when it comes to power. That being said. I was shopping for a table saw, after many years of working with a circular saw, and a straight edge – for me – it was time to get a setup for repetitive cuts that would be easier, and less time consuming (not to mention more precise, as the machine...
All these saws have fences that extend to at least 24 in. to allow you to rip a 4 x 8-ft. sheet of plywood in half. And they all have a slightly different way of accomplishing this. DeWalt has the most straightforward method. You just push the fence out on its rails and flip over the board support. On the Rockwell saw, you flip out a hinged fence rail. The only drawback to this fence is that it must remain in the extended position for any cut, so it takes up quite a bit of room. The remaining saws require you to release one or two levers and pull out the fence extension.
Ridgid’s fence is outstanding for its design. Its large front plate helps stabilize it and the whole thing just feels solid. There’s very little play compared to some of the others and we were consistently able to lock it down perfectly square. We like the pinion style bevel adjustment. It’s not quite a good as a separate adjustment wheel, but a great improvement over simple sliding. We also like the independent locks for both height and bevel. It’s not often that a height lock would be required, but there’s an element of confidence that comes from knowing it won’t be going anywhere.
Skilsaw produced the only worm drive table saw in our group and we had high expectations, especially given the high RPM count. In the end, the power is definitely at the professional level and settled in tied for fourth overall with DeWalt. This was the lightest, most compact saw in the group. Like DeWalt, the lack of an outer housing leads to more efficient cooling but drops storage for an extra blade.
One thing you’ll love about the riving knife is that it allows for adjusting the table saw without using any special tools, for non-through and through cuts including, pictures frames, grooves for shelves, but also cheek cuts for furniture, rabbets and dadoes. There’s also the possibility to store different tools or anything else you may find under the tablet board and given the fact it’s expandable and convenient, it’s going to make using the Delta 36-L552 an even more amazing experience. For dust collection, the table saw comes with a bi-level dust extraction system which offers superior dust collection capabilities.
Let’s face it: guys get in each other's’ way at a job site. It’s not always easy to find room to work, so portability is a serious advantage when it comes to making the most out of your space. Luckily for the professionals out there — not to mention hobbyists who prefer to move around rather than work in the same spot everyday — RIDGID’s 15-amp table saw comes with a convenient mobile cart for stress-free transportation.
Setup was nearly as simple as SawStop’s with just a narrow margin between them. We only needed to attach the handle and bolt the saw down to the stand. The stand is a gravity rise style, but requires you to bend down to ground level for collapsing and extending it. It’s a reasonably solid platform, though a lot of movement throughout the day will leave your back sore.
Contractor saws weigh quite a bit more than portable saws, averaging between 150 and 350 pounds, but are still somewhat portable. They have a heavier, cast-iron table top, and a motor that is usually more powerful than a jobsite saw. Even so, they’re within prices affordable for more committed hobbyists. Contractor saws can range between $800 and $2,000. They’re good for basic cutting tasks, as well as making home furniture and cabinetry work.
If you want a table saw that helps you deliver products faster, the Bosch 4100-09 could be what you’ve been waiting for. It has a Gravity-Rise stand that is built for efficient and accurate setup and takes down.The portable construction makes it easy to bring to any worksite with minimal trouble. Only weighing 39 pounds, you will have no problem transporting this table saw wherever you need to go. The Bosch 4100-09 is a powerful saw that is made for the kind of high precision cutting that professionals and DIYers are looking for. It has a 15 AMP, 4 HP motor that generates 3,650 RPMs for clean cuts every time.
If you’re a professional woodworker, you should expect a standard hookup on any saw. However, you’ll find that no portable table saw does a perfect job collecting sawdust. Since these aren’t enclosed tools like a cabinet saw, there are lots of ways for dust to find its way to your floor and spray around your shop. You’ll want to look for the most enclosed, effective design possible, and pair it with a vacuum system that’s got some heft.
How do you tell what the best table saw is? With so many table saw choices on the market it’s hard to know which table saw is the best fit for you and your woodworking needs. Not for long. We’ve taken the leg work out by doing all the measuring, tracking, and researching for you. We’ve compiled year-over-year performance and pricing information for over 3 years to help you choose the table saw that is ideal for you and your project. Search no more, find your table saw below.
One of the first and most important things to consider is what type of table saw you require. When considering the type make sure you consider things like, where will be using the saw, will it need to be portable and move from job to job or can it be stationary like in a work shop. Also, what will be the largest size bits of timber I will be cutting, what sort of power will I require and budget, below we’ve listed the main types so we hope it helps you find the right type for you.
Not everyone needs to use the miter gauge on a table saw since there’s typically going to be a miter saw around. If you do, you’ll like the positive locking detents at common angles. This saw felt like it was the weakest when pushing our 2x PT material through. Despite the ranking, it doesn’t feel under-powered – you just need to take your time. You won’t find a lot of bells and whistles on this model, but for $279, we don’t have many complaints.
The fact is, a table saw is designed to remove a large amount of material in a quick and efficient manner. With the volume of waste that is produced by any but the smallest table saws, a shop vacuum is not going to be up to the task. Short of purchasing a standalone dust collection system, the best that you can hope for from a shop vacuum is that it might keep some of the saw dust out of your eyes.
I really do like your site and being on Long Island there is a familiarity to the way y’all work. You are quick to respond to comments and put in a great effort but…. This review I feel you miss the mark. Out of box accuracy is important but. Ore important to a pro user is tool able to be adjusted to be near perfect and how does it hold this position. No comments on how solid the fences are, ie deflection movement, ease of micro adjust, etc. all the fancy self feed stuff etc, what saw feels the most powerful? Smoothest ? All theses kizmos are for the manufacturers to hype. Your strengths are that you actually use these machines, so your strengths are to BE MORE opinionated or biased not less because your opinion has meaning or weight. Let the know knowings use the kizmos and just give us your real opinions based on real use. Just my 2 cents.
I appreciate the helpful comparison of the best table saws. I’m fairly new to woodworking, and until recently I was using an old table saw that used to belong to my dad. Long story short, it’s no longer usable, and so I’m looking for a good table saw to buy that’s beginner-friendly. I have my eye on the DEWALT DW745 – evidently it’s really popular and does a great job. I’ve taken a look at some other sites for more ideas. Your guide here is great. What is your opinion on the DW745?
I am a general contractor in the Midwest. I used the saw and stand a lot for the 1 week I've had it. Overall the saw works well, dado blades are easily interchangeable, and it's surprising quiet. However, the stand base bent on me today. I had it passively mounted in the rear of my enclosed 7x16 trailer. Opened the door this morning after arriving at the job site and it had sunken over. I thought maybe it had come out of the mount I made, but sadly that was not the case.
From the triple belt drive system, to the three-HP motor and the large cast iron table and wings, the Shop Fox W18193 s built like a tank. You’re also going to love the T-slot miter gauge that features a fence extension and flip stop, but also a four inch port for dust collection and camlock T-fence. There’s also a twenty nine and a half inch rip capacity.
By the late 18th century, a new tool had been created that would eventually have the sawyers out of work: the circular saw. These early rotating saws were powered by a range of different forces, often including running water or wind, and sometimes driven by animal power. By the early 1800s, the sawmill was replacing the saw pit and its hardworking manual sawyers.
If you’re looking for a machine with high capacity, the SKIL 3410-02 has a 3.5-inch cut height with the ability to cut through four times the material on each pass. The consensus among reviewers is that, for such a low price, you end up compromising on miter gauge and saw blade quality. Luckily both of those things can be replaced if you so choose.  
As you can tell, this particular type is in the middle between portable and contractor. Some people can finish their projects with bench top saws, but the ones who can’t usually opt for hybrid saws because they are cheaper than contractor ones. One cannot say they are cheap per se, but it’s a significantly smaller investment in comparison to contractor models.
The first thing people notice about this unit is its design. The rolling stand is specially designed to mitigate the transport of this saw. In simpler words, whenever you need to move it, you can do it by simply rolling the unit on its wheels. One more notable thing is the 2-inch dust collector port. You can easily connect it to a vacuum and extract the dust efficiently and without much hassle.
Built on the 4100’s foundation, The Bosch REAXX exhibits similar performance with a few improvements. Despite what we’ve seen online, the REAXX did seem to have better cutting power than the 4100. (see Editor’s Note above) The narrow throat plate opening also gave it much better dust collection, allowing only the finest material to make its way out. It shares the top ranking gravity rise stand with the 4100.

If you’re a professional looking for a great table saw for the worksite, you’ll love the features and performance of the DEWALT DWE7480. Equipped with the Site-Pro Modular Guarding System has a rack and pinion telescoping fence rail that will allow you to make fast, smooth and accurate adjustments. This is the perfect table saw for cutting larger shelving and trim easily. With a 15 AMP 4800 rpm motor, you will go through all types of wood, even hardwood, with ease.

Both saws accomplish the same thing, but with different results. SawStop’s feature takes about 90 seconds to recover from compared to roughly 1 minute with Bosch. Bosch developed the REAXX to drop the blade without damage while SawStop usually results in a damaged blade that needs to be replaced. The SawStop employs a brake that must be changed after activation at a cost of $69 each. Bosch uses a dual airbag style cartridge. These run $99 each, but you get two shots out of each one.

It’s highly portable. Even though the whole body feels sturdier than the Dewalt’s, it’s still relatively light, at just about 60 pounds. There are handles in both the top and bottom edges of the machine, for easy lifting, and once you’ve got the saw fixed to the base, you won’t have to lift it on your own except for when you’re loading it in the back of the truck/van.
The miter gauges on these saws range from downright flimsy to cabinet-saw quality. All the saws except the Craftsman and the DeWalt also have T-tracks—a nice feature that captures the miter gauge bar, making it easier to start wider crosscuts. Because the Ryobi and DeWalt saws don’t have a standard miter gauge slot, you can’t use accessories that require a 3/4-in. slot.
One thing you’ll love about the riving knife is that it allows for adjusting the table saw without using any special tools, for non-through and through cuts including, pictures frames, grooves for shelves, but also cheek cuts for furniture, rabbets and dadoes. There’s also the possibility to store different tools or anything else you may find under the tablet board and given the fact it’s expandable and convenient, it’s going to make using the Delta 36-L552 an even more amazing experience. For dust collection, the table saw comes with a bi-level dust extraction system which offers superior dust collection capabilities.

As with anything, it’s easy to get overwhelmed with the variety of types, sizes, features, colors, weights, what, when, why, where, who…(let me catch my breath). For now, let’s focus on what’s right for you with our Best Portable Table Saw Guide. We’ll start by identifying quality brands that align with your needs. Besides, who wants to buy something that won’t work?

One thing manufactures noticed over the years was that when people used the splitters in normal straight cuts it worked well but it’s biggest downfall came when contractors wanted to do cross cuts. What would happen is that people would remove the splitters to make the cross cuts but then forget to fixed them back in place. One brilliant table saw safety feature is the riving knife. The Riving knife is attached directly to the blade mechanism, this allows it to always be attached not matter where or what angle the blade is.
That’s why we’ve created this handy guide! As usual, our trusty team have taken a comprehensive look at all the options out there. We’ve looked for portable units that don’t sacrifice power or accuracy for their small size. You’ll find our Top Three recommendations below, along with a few additional choices for new woodworkers and demanding professionals.

Probably one of the things that users will love most about this table saw is the solid granite surface which offers a seamless work area and excellent support. Another advantage of the Steel City 35955 is the fact that it comes with powerful magnets which allow swift changes without having to worry about using any type of tools. Since there’s a built-in mobile stand, you can easily position the saw around your shop without requiring the help of a second person.

Most table saw blades come in 8, 10 or 12inchs in diameter, but you can also get a lot smaller and larger sizes if you require special cut sizes and cut depth sizes. When looking for a new blade when it comes to sizes, blades are measured in two sizes mainly, the mounting hole and the total blade diameter, make sure you take the mounting hole size in to consideration when buying a new blade as this could be something very easily over looked but could cause an issue.


It’s sturdy. This unit also has a metal roll cage frame all around, which helps it handle the rough and tumble of travelling to worksites on a regular basis. It has a locking mechanism to help it stay securely on stands. We’re also super impressed by how well-made the adjustment knobs feel on this one. Buyers reported using this one for several years with no issues.
With this saw, it was a very easy thing to plug it on and get started. The included cord is a reasonable length, but you’ll still need an extension cord unless you happen to be right next to an outlet in your workshop. Raising and lowering the blade is a smooth process and we found the mechanism to be nice and stiff, so you can be very precise with your cut depth. Only time will reveal whether or not this stays tight over the long haul, but it seems to be well-made. Mounting the accessories, like the smart guard system is quick. You just raise the riving knife using the release lever. The riving knife locks into a lower and upper position through the use of two sets of pins. In the upper position it is ready to accept the barrier guard, which you can remove from below the saw. It attaches easily with a lever lock and the anti-kickback device can then be placed on the back of the riving knife such that the teeth are set to grab any wood brought forward by the blade. The physical nature of the barrier guard assembly precludes you from placing your fingers anywhere near the cutting surface of the blade. We (and Bosch) recommend keeping this guard on the saw anytime you are doing “through” cuts. All-in-all, the table saw’s included safety features are more than adequate to keep you from encountering any unfortunate accidents. Removing them, or using the tool improperly, however, will considerably raise your level of risk.
When choosing the best table saw for jobsites, you’ll need a rip capacity of more than 24″. Why? 24″ is half the width of sheet material. Some models will give you as much as 35″. Since you ideally want to have the waste edge opposite the fence, the larger the capacity the better. But again, jobsite table saws are designed for Pros with a little more inherent forgiveness in the job, so the assumption is that you can cut the waste edge against the fence if necessary.
For benchtop and jobsite saws with direct drive motors, the motor RPM is the blade RPM. If you’re considering a contractor or cabinet saw, it’s a different story. In any event, Pro table saw RPMs generally range from 4000 – 5000. Don’t let numbers on the lower side dissuade you. There’s a limit to how much power you can draw and each manufacturer has to decide how they’ll channel it between blade speed and torque. So higher isn’t necessarily better.
You’ll make most of your miter cuts on a miter saw. But when the material you’re cutting exceeds a miter saw’s cross-cutting capacity, you turn to your table saw miter gauge. These usually aren’t quite as precise, but some manufacturers put more thought and robustness into it than others. If you make a lot of long miter cuts, be sure to pay attention to this accessory.
Table saws will use one of two different kinds of drive configurations; Direct-drive motors and Belt-drive motors. In a direct-drive motor, they will link directly to the blade itself and transfer all of the power of the motor to the blade. They tend to last longer than belt drive motors and there is no belt to replace or worry about getting worn out. Belt drive motors transfer power from the motor to the blade through a belt. In this type of configuration, the motor can be offset away from the sawdust which helps the motor last longer. In general, belt drive motors need more preventative maintenance than direct-drive motors do. If you have a belt drive motor, check the tension of your belts as well as checking them for wear periodically to ensure your continued safety.

You can store and transport the Bosch upright or on either of its sides. In between our tests, we found that the saw neatly stored away on its side on a workbench shelf. On the other hand, the DeWalt can only be stored or transported in its upright position. While it may possible to rest the saw briefly on one of its sides, there is the potential to damage the power cord, plug, or the ends of the telescoping fence rails.
The Bosch will deliver a whopping big 25” rip, where the DEWALT maxes out at a 16” rip. Again, if you like the other features of the DEWALT better than the Bosch, this larger rip capacity might not sway your buying decision one way or the other. Personally, i would lean towards bosch, but that’s just me.It truly is the best portable table saw on the market today.

The stand strays from the idea that jobsite stands need to be wheeled. We can attribute this to its light weight. While it loses points for portability, Skilsaw’s design created the most stable stand of the entire group. Another benefit to going with this simple stand design is that it is certainly responsible for dropping the price point. Skilsaw is definitely the table saw you want to go with if you’re having to move your saw in and out of a truck bed rather than being able to wheel it up in a trailer.
This saw has a soft start and also seems to over-rev and then slow down to correct itself upon startup. Strange, and I'm hoping this isn't a precursor to a problem down the road but for now it works fine. The Bosch blade that it comes with was removed and replaced with a Freud. The saw cut like a hot knife through butter and I am very pleased with the overall performance. The miter gauge is a little sloppy in the miter tracks.
Disclosure: daringabroad.com blog is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Additionally, daringabroad.com participates in several other affiliate programs, and we sometimes get a commission through purchases made through our links.
×