Welcome to the heart of this website – my selection of the best table saws for several specific needs. You see, it’s impossible to select only ONE as the best for all purposes because a table saw should be carefully tailored to your needs. There’s no point in buying a complex cabinet saw if you’re a beginner, you’re probably better off with a solid benchtop saw. The same goes if you’re a professional, only the other way around.

Safety and precision are usually at a high level. Some models even offer a sliding table as an option to mitigate cross-cutting. Needless to say, hobbyists love the sliding feature because it saves a lot of time and most importantly – nerves. As far as the driving mechanism goes, there are three possible options – single V-belt, serpentine belt, and a multiple V-belts.
This is a truly great saw, except that it is really tough to adjust the blade and rip fence for parallel. Once adjusted though, it is a fine piece of engineering. What I like best is that the saw is built for the job site. It is extremely beefy, but no too heavy. In my opinion, it strikes a nice balance. Its cart stand is the best in the industry, bar none. Once adjusted, the saw returns to its settings extremely well. It is obviously built for the long haul, and should last a contractor many years. I would definitely purchase this saw again. Now with the things that I wish were better. First, adjusting the blade for parallel is just plain hard. Mine was out from the factory by 4 thousandths. It is a trial and error process, and the instructions suck. Here's what to do: 1. Loosen the four screws indicated in the instructions. Starting from behind the saw, center the blade housing in the rear left to right as best you can, then tighten one screw not quite snug (you want the housing to rotate on this screw when you adjust the front). Next move to the front of the saw and loosen the lock lever for blade angle adjustment (the housing won't move unless you do). Now, begin experimenting with holding the housing at 90 degrees with one hand while sliding the housing back and forth with the other until square. When you think that you are close, lightly tighten one of the front housing screws. Check for parallel (look for videos on how to check a table saw blade for parallel), then tighten the blade angle adjustment lever. With these screws and the lever tight and locked, check again for parallel. If it is still good (I got it to 1/1000 inch of parallel), then lock all the screws and check one more time, if it's still good, then you are done with blade housing adjustment.
On the other end of the handyman spectrum, you’ve got the seasoned professional with years of experience under his belt. We all know the type: he’s the guy that expects only the best, and DEWALT more than delivers with their patented DWE7491RS. This wood-slicing machine is the cream of the crop when it comes to cutting through even the toughest materials. The DWE7491RS measures 26¼" x 22", so it’s a relatively large apparatus — you’re going to want to make sure that you have plenty of space in your garage for this table saw.
We used the Freud calibration plate on each of the test saws to measure runout. We removed the new Diablo blade, installed the calibration plate, and raised the trunnion to its maximum vertical adjustment. Before measuring the runout, we placed a black mark on the calibration plate to give a consistent starting position for the runout test. The same iGauging dial indicator provided the test measurements, only this time, the units were set to read out in mm. TBB noticed that in the initial saws, the movements were sufficiently small to need the smaller metric units.
It’s tough to be completely objective when choosing the best portable jobsite table saw since the stock blades vary so widely. Skilsaw comes with a 30-tooth Diablo blade and Makita’s stock 32-tooth blade are both excellent while others could use some help. To make this shootout about the saws and not the blades, we turned to Diablo to outfit each saw with the same accessory.
The CNS175-TGP36 SawStop is a 10 in. contractor table saw with a 45 degree bevel and a rip capacity of 36.5 in. Other than that, we think this is a pretty cool table saw for a few different reasons. First, the price is about half of all other SawStop table saws, and we know money talks (actually, it yells)! Second, like all other SawStop table saws, it has the integrated flesh sensing technology, so you can be sure you’re going to keep all your digits. Also, it has some pretty impressive power; it’s powered by 15 A motor so you’ll be able to tackle whatever you need. The last of our favorite features is its portability. For being a contractor saw, it’s pretty easy to pack up and move around.
Setting up both saws was quick and easy, since their factory-adjusted blades and fences were square and parallel to the tables' miter gauge slots out of the box (this is one of the reasons to buy a $350 table saw over a $100 one). Both saws had similar setup procedures: Attach the fence, raise the riving knife, attach anti-kickback pawls and attach the blade guard. There is no on-board stowage space for the DW745's rip fence, but this does not really affect the setup time or effort by much.

Electric brakes in the saw is an important feature as helps the saw in reversing electricity in the motor, thus contributing to a precise cut. It is highly recommended that when you are buying a saw choose the one with on and off switch. The switch should be easily accessible to make work better and more efficient. In addition, the switch should have a cover. This will keep you from accidentally turning the saw on and damaging your work area or cutting yourself.

Kenny Koehler An avid endurance athlete, Kenny has competed in triathlons (he's an Ironman) and various other fitness activities. Still, his passions lie with his faith, family, friends, and his love for well-designed power tools. With a background in science, you'll often find Kenny chatting up engineers at media events to get caught up on the latest tool technology.
The DCS7485T1 60-Volt MAX 8-1/4 in. table saw The DCS7485T1 60-Volt MAX 8-1/4 in. table saw is maximized for accuracy capacity and runtime. The brushless motor delivers the power to cut all common materials the rack and pinion fence allows for fast easy adjustments and provides the capacity to rip 4x8 sheet goods. The DCS7485T1 comes with 1 ...  More + Product Details Close
post-template-default,single,single-post,postid-5859,single-format-standard,mkd-core-1.0.2,ajax_fade,page_not_loaded,,table saw theme-child-ver-1.0.0,onyx-ver-1.4.1,vertical_menu_enabled, vertical_menu_left, vertical_menu_width_290,vertical_menu_background_opacity_over_slider vertical_menu_background_opacity_over_slider_on,smooth_scroll,side_menu_slide_from_right,wpb-js-composer js-comp-ver-4.7.4,vc_responsive
It has a machined aluminum table which is extremely precise. We like the Dewalt’s cast metal table for the price, but the company don’t list the material, and we suspect it’s not nearly as rugged as aluminum. The Bosch’s table is much better. It’s rugged, sturdy, and more consistently even than the Dewalt. The table makes this one a smarter choice for fine woodworkers or pros who need superior alignment.
The scales that indicate the width of cut fall into one of two categories: continuous and separate. Of the seven we’re reviewing, DeWalt, Ridgid and Rockwell are continuous. You simply line up the fence with the desired measurement. The other four best table saw options—Bosch, Craftsman, Ryobi and Porter-Cable—require you to lock the fence in a specific position on fully extended rails, and read the dimension on a separate scale. We prefer the continuous scales and really like the tape measure–type scale on the Ridgid.
The rip fence has a nifty flipping action so you can hold 2 different positions. This is an awesome feature if you’re cutting especially narrow workpieces. One of the dangers of ripping substantial pieces of lumber is breakage or the saw itself toppling over. The rail extension gives wonderful stability and allows you the freedom to undertake ambitious projects in complete safety.
Move the wood to and then "through" the spinning saw blade slowly and steadily. It's alright to use your hands while you're still at least a foot or so from the blade, but once the end of the board or sheet nears the blade, you should use a pushing stick to keep the wood moving and to keep your fingers away from the blade. Even an experienced carpenter can have a lapse in concentration or a slip that can lead to serious injury.

The DCS7485T1 60-Volt MAX 8-1/4 in. table saw The DCS7485T1 60-Volt MAX 8-1/4 in. table saw is maximized for accuracy capacity and runtime. The brushless motor delivers the power to cut all common materials the rack and pinion fence allows for fast easy adjustments and provides the capacity to rip 4x8 sheet goods. The DCS7485T1 comes with 1 ...  More + Product Details Close
The saw’s table measures 29 x 21.5 inches which makes this unit suitable for the fabrication of large sheets of material and large wood stock. The table is made out of aluminum and is really smooth which means you will be able to slide even the largest pieces in with very little effort. Still, for extra safety, I would recommend the optional extensions when ripping longer workpieces.
Previous buyers said they were at a loss to find materials that the Jet couldn’t cut! They said it went like butter, with no lag whatsoever, and almost no vibration at all. Reviewers raved about the motor’s power, and especially complimented how steadily it ran. This is an excellent choice for hardwoods, thick softwoods, and composite boards: absolutely anything that’ll fit.
so.categoriesWithItems ='8003,8002,8005,797,8007,696,8009,793,8011,8010,8013,750,8015,8014,833,823,825,8023,841,8017,2669,470,8041,430,8044,8047,263,8048,8050,306,8051,8053,5954,8055,8054,5957,8056,166,8059,39936,39934,39935,508,8025,5960,139891,139893,8030,566,8031,139905,8034,8033,8035,649,647,8038,661,491149,8742,505663,491151,505665,8277,143,8278,2234,8280,1224,2310,8285,8287,1222,116,6237,8292,8293,8294,8295,8296,8297,8298,8299,8300,8301,139847,139871,9022,39752,39751,39753,39754,997,8077,1022,1032,1025,8082,994,8084,139649,941,944,6471,910,8085,8087,1014,914,8090,8092,1258,8094,139687,8805,39895,39894,39896,39897,8063,224,8064,8065,5956,5959,429,39909,39908,39910,8130,5941,8131,902,1196,8137,8138,8141,8143,8142,8144,8145,1416,8148,8150,8151,1554,1422,8167,8163,8172,8174,8173,8182,8179,8183,39667,39665,469559,37938,469561,469563,37941,37940,37943,37942,37945,37944,37947,37946,3,8185,43,23,35,8191,8194,8195,1642,8196,8199,8200,139409,139411,452623,8203,8202,8204,8205,8206,8209,8210,139437,1299,1664,8216,8217,139455,139459,39703,39702,39704,108845,108843,8112,8111,8116,8114,8117,8115,8118,8106,8105,8107,8108,8109,8120,1132,8121,8122,8123,8126,6269,8221,681,8222,8220,8224,2584,8226,2575,678,662,2593,663,675,843,1699,8235,1805,8238,5980,8241,8244,8246,8247,5987,8248,8250,2614,6517,8253,8262,1307,139301,8264,187,8266,8265,8268,8267,8270,8269,8272,8271,8273,8274,39820,39819,108974,108972,468779,108975,139363,139359,139371,139369,930,928,2804,8101,919,8103,8102,39766,39765,139783,139767,108849,108848,108851,108850,140169,140167';
Cabinet saws are the prime choice for professional woodworkers. A more powerful induction motor, usually 3 to 5 HP, is enclosed in a cabinet, as part of a super-sturdy overall construction. This type of table saw is ideal for making smooth, straight cuts through hardwoods without worrying about excessive vibration. All that power and stability comes at a price, though. Low-end cabinet saws start around $2,300 and can go past $5,000 for industrial table saws.
If you’re looking for the perfect cabinet table saw out there, then you should look no further than the SawStop ICS51230-52. This is an industrial grade cabinet saw and is also the highest quality, most powerful and heaviest cabinet saw you can currently get. Its fifty two inch industrial T-glide fence assembly, combined with a 5 HP, 230V single phase motor offers safety, versatility, durability and peace of mind that SawStop is so well known for.
Because we’re passionate woodworkers who care deeply about the quality of the tools we work with, we have a tendency to recommend that even the most budget-conscious buyer spend a little more to get something high-quality. However, we know that some DIYers might have the ambition to take their woodworking to the next level with a table saw, but might not necessarily have the funds.

The professional level saws saw a separation as well and all were well ahead of the cutting power we saw with the value group. A middle tier of cutting performance started with Makita and Bosch’s 4100 while DeWalt was significantly better. Entering the fray with the only worm drive system, we had high hopes for Skilsaw’s entry. It was solid and smooth—definitely at the Pro level— and close to what the 4100 delivered.
Cabinet table saws are the best choice for full-time professional woodworkers with a dedicated workshop. If you have a spacious shop, these are some of the most efficient, versatile cutting tools you can buy, especially for larger stock. With 3+ HP motors, they’re by far the most powerful machines you can get your hands on. Plus, their heavy, machined build quality gives you a precision and smoothness in your work that really compliments the professional. They have the most effective dust collection systems of any table saw, and durability that can last more than a lifetime.

The safety brake feature is a real step forward in engineering, but it does have a few downsides. The aluminum brake works with single-use cartridges, so you’ll have to replace the cartridge if you trip the sensor. Likewise, the impact of the brake, stopping the blade in milliseconds, will destroy your blade, so you’ll have to replace that as well. It’s a small price to pay for keeping your fingers or limbs, but it’s probably a good idea to stock up on cartridges and blades


Robert Bosch Tool Corporation is aware of questions raised about the power of its REAXX™ Jobsite Table Saw. We are taking this feedback seriously and we’re working with product and engineering teams to answer these questions. Flesh-detecting Bosch Active Response Technology™, which comes on board every REAXX Job Site Table Saw, is unrelated to the questions raised about the saw. The REAXX table saw remains one of the safest and most-advanced table saws available today. 
The dual extension tables (rear and side) offer 50% more table space than most rectangular units. We also appreciate that Grizzly have put all the space under the worktop to use, with steel-frame shelving built in as standard. You can use it for scrap wood, tools, and accessories: you can even fit a full tool chest under there! It’s a good space-saving touch for busy shops.
The Bosch weighs in at 52 lbs. While you could carry it one-handed, and it feels well-balanced, it would throw your personal balance way off and tire your arm. The DeWalt is a little lighter at 45 lbs., but it feels even lighter than that, and its weight distribution makes it feel less fatiguing to carry back and forth. (You can also carry the Dewalt saw one-handed by its handle or roll cage, but you probably won't want to.)
A lot of the modern table saws nowadays will have a dust collection port where you can hook up a vacuum or extraction system to it. We would always recommend that you purchase a table saw with a dust port, always check the size of the port to make sure it fits with either your vacuum or your extraction system, or you can always modify something to make them fit.
Excellent saw. Got here sooner then expected. Fairly simple to put together. Folding stand is very solid and easy to operate. Takes up very little space in my garage. I've never owned a table saw before so I'm easily impressed. Some other buyers recommended upgrading the blade, which I did. The blade it came with was ok but the Freud 10 in. 40 tooth Premier Fusion makes a very smooth cut. I haven't hooked up dust collection to it yet but it seems like it would work great. The scale for the fence is spot on. I would highly recommend this to any diy.

In other words, a malfunction might mean an injury. This distinction could not be more pronounced in any other job site equipment than a table saw. I have personally witnessed devastating injuries on a number of occasions that could have easily been avoided by the use of safety equipment that comes standard on most brand name saws. Liability for a job site injury can be a serious setback for well established companies, but for small, independent contractors it could mean the difference between business and bankruptcy.
I do not which is the best table saw, but I can tell you which is the worst. The rigid portable saw is a piece of garbage. I have purchased two in the last 4 years and the motor has failed in both, only to find that they do not sell a replacement motor. The Rigid customer service will not respond to any questions associated with the saw or replacement parts. I will not buy another Rigid tool and currently planning to try the Bosch table saw.
For the woodworking professional, the 3-horsepower SawStop Professional Cabinet Saw PCS31230-TGP236 is the top pick. Its superior safety features include an excellent riving knife and blade guard system and a unique flesh-sensing blade brake to prevent cuts. Reviewers also praise its performance, exceptional dust control, and overall ease of use. Less expensive versions with 1.75-hp motors are also available (Est. $2,300 and up). The warranty is two years for the saw and five for the motor.
You will agree that your ability to hold, controlling and manipulating the saw largely depends on your strength. Since small table saws are lightweight, you should go for a powerful table saw so as to avoid fatigue during small jobs. This also means that if you are working in a forest for a whole day the light weight is of great importance it also helps reduce fatigue. When shopping for chainsaws ensure the saw balances well in your hand. You should also ensure that you can easily shift the saws grip from hand to hand without losing its balance.
×