While it’s bargain-priced, it has very impressive cast iron and steel construction, with all the same essential features as our other top table saw recommendations. On the downside, it’s the slowest of the three in terms of blade speed, and it has the shortest warranty coverage. This one also lacks some of the sophisticated safety features and creature comforts of our more expensive recommendations.

There are two major points that affect post-calibration table saws: fence quality and overall stability. A fence works by grabbing hold of the table edge and clamping into it. The best fences, like Biesemeyer, have three points of contact. They’re just not where you’d expect. All three are on the front, leaving none on the back. With a wide cast metal front clamping system, the front is pulled flush and self-aligns. It requires a solid locking mechanism to ensure the fence doesn’t move during cuts, but it is very possible.
Bosch engineers deserve kudos for the Gravity-Rise stand, and it’s a design some other manufacturers should emulate. Twist one lever, and the sturdy, steel frame folds up or down fluidly to convert from sawing to transport or storage. Eight-inch wheels and lugged rubber tires make this base easy to steer overland or pull up steps. Plus, the base’s stance is wide, giving it sure footing if you are pushing long planks or heavy sheet goods through. It will not tip. But, the stand when erected sets the saw’s tabletop quite high, at 38-1⁄2″. Shorter users may find this to be a bit too tall for comfort.
When you purchase your table saw, more than likely it will have standard 10” carbide tipped blade that is good for general purpose use. This blade is capable of cross cutting a 4 x 4. If you replace it with a 40 tooth combination blade you will improve the quality of your cuts significantly and more than likely be much happier with the blade overall. You can get specialty blades also if you are going to be cutting other materials as well.

The design is not bad. The height of this particular table saw is around 35 inches. While some people don’t mind it, we think it could have been designed better. However, the best thing about the design is the fact that you can get both contractor and cabinet style table saws in one unit. Dust control is well-designed. The large 4-inch dust port offers a no-hassle setup, especially with vacuums of lower quality. In simpler words, you don’t need to purchase a super-expensive vacuum for this particular unit; any affordable one should do the job well.


These saws are the most difficult ones to categorize. The simplest explanation would be that they are somewhere in the middle between contractor and industrial cabinet saws. They are driven by an inboard belt motor. These units usually have open leg stands, but there are some models with closed ones – hence the whole confusion and difficulty in categorizing.
You can’t talk about the best portable jobsite table saw without talking about portability. Portability boils down to a couple of important features. First and foremost, weight has a huge impact on how easily you can transport the saw, especially if it has to go into the bed of a truck rather than a trailer. If you’ve got a trailer, then a wheeled stand becomes your best friend. We looked at both.
In addition, a top-quality fence should move smoothly and have a scale that’s accurate and easy to read. Our favorite is the DeWalt fence. The rack-and-pinion system keeps the fence parallel to the blade, and the micro-adjusting knob allows easy and precise fence positioning. Runners-up in this category for best table saw are the Ridgid and Bosch saws. They both have superb fences, with the added advantage of T-slots for attaching accessories like featherboards.
To avoid such scenario, you can take a moment and check our full reviews out. We offer more than enough insight into the capabilities of particular models we consider are worth checking out. Therefore, if you’re in a dilemma about which table saw to buy; don’t hesitate to refer to this article. The more you know about a certain unit, the fewer problems you’ll have when the moment of purchase comes.
Buying a table saw is one of the biggest and most important purchases you will ever make when it comes to power tools. It is an integral part of most job site equipment, as well as an essential item for most do it yourself projects. Choosing a table saw that fits your particular needs and budget can mean the difference in both profitability and frustration level.
You will not always get your job within the workshop, there are moments where you will have to get out and work from a distant place. Therefore, you will require having a table saw that is portable and reliable for such duties. Rockwell table saw with a laser has large legs with wheels. You can easily pull it to any place comfortable as the wheels keep rolling. In other words, you will not have to struggle with the entire unit trying to lift it when you want to switch working positions. Additionally, this table saw has a foldable fence for convenient storage and also ensures there is enough room for all size material. The inclusive laser guide is to ensure you get consistency in accuracy. Once the blade is not in the position, the laser guide adjusts automatically for the benefit of the user.
As for my blades, I replaced the blade that came with the saw right away. It is terrible and would have been better to be not included at all. I replaced it with a Freud industrial 24 tooth glue-line rip blade and a Freud Diablo 80 tooth plywood and crosscut blade (I find it easier to just buy new plywood blades since the glue does a number on them, not to mention the wear and tear caused by MDF). As an all-around blade, I keep a 50 tooth Tenryu Gold blade. It is quieter somehow, and does a cut almost as good as either the rip or crosscut blade. Great for making quick cuts without always changing blades. I will use it for most ripping, but will switch to the ripping blade when I have a lot of ripping to do, or will be going thicker than about 1.5” in hardwood.
Bengt – We appreciate the feedback as it always helps us get better. Having said that I think some of your concerns were evaluated and included in the results in ways that may not be entirely clear. We adjusted each saw after checking the blade/fence measurements and had no issues getting them adjusted (I may add some text to reinforce that in the article). We don’t do long term testing in this type of article as it’s simply not feasible…so making a statement about whether the saw holds those adjustments isn’t feasible. We evaluated the fences and ranked them in the ergonomics section, we even did lateral load testing on them as part of that ranking.
Let’s face it: guys get in each other's’ way at a job site. It’s not always easy to find room to work, so portability is a serious advantage when it comes to making the most out of your space. Luckily for the professionals out there — not to mention hobbyists who prefer to move around rather than work in the same spot everyday — RIDGID’s 15-amp table saw comes with a convenient mobile cart for stress-free transportation.
If you want to have a quick and accurate cut of wood, look no further than a table saw. When buying a table saw the main thing you put into consideration is its power. A good table saw should have enough power to cut through wet timber as well as hardwood. However, there are certain features which help in foreseeing the overall performance of a table saw.

That’s where we come in! As your saw experts, we’ve taken a comprehensive look at all the models on the market right now, to help you find the best table saw for your projects and your lifestyle. We compared dozens of options, drawing on our own collective experience as well as professional ratings, and reviews from buyers who spent time using these saws in their homes. We compared specs, features, reliability ratings and more, to find the absolute best options out there right now.


It’s compact. This one is just over two feet in either direction, and just under 14 inches high. It’s easy to fit in the back of a truck, or even on the passenger seat next to you on the way to your jobsite. It’s light, too. Buyers loved how easy this one was to carry around, especially home DIYers who had to set up and take down their units frequently.
Rockwell is the “freshman” brand among the other longer-standing benchtop power tool companies represented here, and its table saw revealed some “first rodeo” shortcomings. While the motor was amply powerful for my cutting tests, the blade arbor assembly was 1/16″ out of parallel with the miter slots. It’s a condition called “heeling” without easy adjustment in the manual. So, for my testing purposes I had to set the rip fence askew in order to align it parallel to the blade. The problem would need to be addressed on this sample saw for long-term use.

Look for a blade guard and splitter assembly. The guard will keep your fingers and sleeves away from the blade, while the splitter will keep your wood from re-binding together and jamming the blade, or causing kickback. Kickback is one of the biggest hazards of using a table saw, aside from coming in contact with the blade. Make sure you have either a splitter assembly or a riving knife on any cabinet saw you use.


When it comes to power tools, table saws provide convenience when tackling DIY jobs or larger commercial tasks. With their table surface, you are able to get more accurate cuts with the materials you are working with. Utilizing the miter gauge, you will find these power tools to provide the same accuracy as your favorite circular saws without the hassles.

While your table saw is unplugged, take the time to clear and clean the work surface, removing any debris that could negatively impact the smooth path of the wood you will be cutting. Then, lower or raise the blade to where the blade gullet (the curved section between each blade tooth) is equal with the top of the piece of wood to be cut. Also, make sure that your saw's dust exhaust port is clear and open and that a bag is in place to catch any excess sawdust.


One shouldn’t expect a massive amount of storage, but being a table, it does offer some level of free space. In fact, some models even offer space for fences, gauges, blades, and other necessary equipment. Apart from that, you can always keep the necessary tools in the reach of your hands. It will make the process much easier and also a lot quicker.
As with the smaller Dewalt we’ve recommended, this one has very inconsistent quality control on the table. Some reviewers cited units with bowed, funky surfaces, while others got units that were perfectly flat. that’s a flaw of the molding process. We also have a bone to pick with Dewalt as far as the coating on these. While we understand that the coating is supposed to help wood slide better, it just doesn’t seem to last very long or hold up well. It also has the same flawed warranty coverage. We’d recommend purchasing add-on coverage.
There are several types of table saws. The types of jobs or projects you plan to use a table saw for will determine which type you buy. If you want a saw you can take from job site to job site and store it easily, then you will need a table saw that is made to be portable so that it can be easily transported to the job site. Of the portable or work site table saws on the market today, the Bosch 4100-09 10-Inch Worksite Table Saw with Gravity-Rise Stand and the DEWALT DW745 10-Inch Compact Job-Site Table Saw with 16-Inch Max Rip Capacity are two of the most popular.
Like the last SawStop table saw that we looked at, this one is quite heavy and provides the stability that you need when working with plywood or any other type of wood. You can use the foot pedal on the bottom to operate the saw, but you’ll also find four wheels on the bottom of the cabinet. All four of those wheels swivel in a 360-degree direction to help you move the cabinet to any location.
The obvious starting point for an analysis of which saw is best suited to the needs of a given person (or company, school workshop, and so forth) is the budget at hand. Even the most affordable table saws of a quality meriting serious consideration cost more than 200 dollars; such units are small but still capable of many tasks. The top of the line table saws come with price tags topping out at well over 3,000 dollars and can handle almost any lumber you would ever need cut and then some; more often than not these mighty saws are more tool than needed, so to speak.
It has a machined aluminum table which is extremely precise. We like the Dewalt’s cast metal table for the price, but the company don’t list the material, and we suspect it’s not nearly as rugged as aluminum. The Bosch’s table is much better. It’s rugged, sturdy, and more consistently even than the Dewalt. The table makes this one a smarter choice for fine woodworkers or pros who need superior alignment.
Contractor saws weigh quite a bit more than portable saws, averaging between 150 and 350 pounds, but are still somewhat portable. They have a heavier, cast-iron table top, and a motor that is usually more powerful than a jobsite saw. Even so, they’re within prices affordable for more committed hobbyists. Contractor saws can range between $800 and $2,000. They’re good for basic cutting tasks, as well as making home furniture and cabinetry work.
The Powermatic 1792001K PM2000 is an award winning cabinet table saw that features a 1-phase, 3 HP motor with rout-R lift and Accu-fence system which set a new standard for innovation through thanks to the saw’s large body design and an incredible range of patented features. The 1792001K PM2000 is the result of years of work and research and hundreds of interviews with woodworkers that offered input which was eventually implemented in the saw. The performance, reliably and safety of this saw are so great, that they actually set a new standard by which all other cabinet saws are judged.
Ridgid notches a third place finish as the only saw to include an independent blade height lock. The adjustment wheel raises and lowers with multiple full turns like most saws, but integrates a lock into the center. For the bevel adjustment, the outside of the height adjustment wheel turns a rack and pinion style system to accurately change the blade angle – a feature Makita shares.
DIY-ers love this type due to its simplistic yet effective operation. However, it’s not unusual for professionals to invest in these in order to avoid investing in cabinet models and save some money. Speaking of money, you should prepare yourself for a hefty investment if you opt for this particular type. However, most models are well-worth the money. These things last for years and don’t require a lot of maintenance apart from occasional blade replacements and minor adjustments.  They are not as easy to use as portable models, but you’ll learn how to use them in a matter of hours or days, as long as you follow the rules written in the user manual.
It’s the safest of the three by a long, long shot. SawStop became a major brand thanks to a feature that they’ve named their brand after: an accident-proof stopping mechanism for the traditional table saw. The innovative brake system on this model is the best on the market at detecting flesh and stopping the blade immediately. It’s a sure bet for saving fingers or worse injuries in the workshop.
This saw has a soft start and also seems to over-rev and then slow down to correct itself upon startup. Strange, and I'm hoping this isn't a precursor to a problem down the road but for now it works fine. The Bosch blade that it comes with was removed and replaced with a Freud. The saw cut like a hot knife through butter and I am very pleased with the overall performance. The miter gauge is a little sloppy in the miter tracks.
If you’re a home DIYer, dust collection shouldn’t be a big worry. You can always hook the saw up to your shop vac, but if you’re only working with it occasionally, you’ll be fine to simply get your sawing done, and clear the exhaust port afterward. However, if you’re working on a professional jobsite, you should plan to collect at least most of the dust from your portable table saw via a vacuum system.
I got the Hitachi 1 1/2 mouths in the motor died. Says it has a 5 year warranty. I’ve been trying for weeks to get it resolved. Ended up giving up and headed to buy another saw. I understand having products be faulty it’s a numbers game it has to happen to some one. How ever the complete no help to resolve it from Hitachi. Is a problem after a week of back and forth they said they would set up a pick up time to ship and get it repaired over a week still no call back for a pick up. I can’t say enough avoid this headache. I’ve been a contractor for a decade and have had may tools break or need repair. First experience I’ve had that’s made me swear off a brand.hope this will save some one from wasting money and time
For carpentry projects or as a starter saw, the DeWalt DW745 receives solid reviews. Though it doesn't have the capacity of the Bosch, owners say it's well made and easy to adjust. The rack-and-pinion fence earns kudos for accuracy. The saw weighs just 45 pounds and can even be hung on a workshop wall for storage; an optional is also available. The three-year warranty is another plus.

No matter the model or price, a table saw should cut a range of material thicknesses and hold its settings accurately. So, after installing a new Freud hi-ATB thin-kerf blade in each saw, I made repeated rip cuts on MDF, resetting the fence each time to check for consistently thick offcuts. After that, I raised the blade for more rip cuts on heavy, long planks of 2 x 12 Southern yellow pine, before tipping the blade to bevel-rip 2″-thick poplar. Then I switched to a 6″ CMT dado set and made a long dado cut in MDF, so I could check for consistent cutting depth — a sign that the undercarriage is stout enough to handle a heavy blade like this. Overall, my test criteria was stability of the stand, cutting accuracy, reasonable dust collection efficiency and all-around convenience of use. Results ranged from exceptional to mediocre, as you’ll see.


It has a brilliantly powerful 15 AMP motor, which can deliver 4,800 RPM of cutting power. Is is normally more than enough for most woodworkers and hobbyists. It has stowable anti-kickback pawls and and excellent riving knife and spreader for accurate cuts. This is a great entry level saw at a great price, definitely worth looking at for your next purchase or project.

If you are an avid hobbyist, this saw is made just for you. The company is known for its uncompromising quality and durability. This saw has a safety system where the blade stops and retracts automatically when it comes into contact with anything that is not wood.  The microblade guards keep debris from flying all over your workshop. It is easy to change between blades. You will not require a riving knife to do this. Its award-winning dust collection system ensures that you have a clean and presentable workspace at the end of the day.
×