TBB measured the accuracy of the factory-set 90 degree stop by using a Wixey WR365 digital inclinometer. This device has an accuracy of 0.1 degree. We placed the Wixey gauge on the table and calibrated the inclinometer to the table by zeroing out the gauge. After that calibration, the measurements give a result that is relative to the saw table. We moved the blade to an approximate position of 70 degrees off vertical. TBB attached the gauge to the blade and used the saw mechanism to adjust the blade incline to the point at which the blade or trunnion hit the factory-set 90 degree vertical stop and recorded the measurement. TBB ran the test twice to ensure the repeatability of the measurement. In every case, the result came out to within 0.1 degree of the prior test.
Their 15-amp, 120-volt motors cut with greater ease than a circ saw, although they can bog down if fed thick hardwood too quickly. The cabinets are typically plastic, with cast-aluminum tops and extruded-aluminum fences. In these models, the motors are supported by trunnions mounted to the underside of the table. The resulting vibration reduces accuracy. These trunnions are usually made of lightweight steel or aluminum, which are susceptible to wear. And because these saws are small, cutting full-size sheets of plywood or MDF isn't a good idea unless the sheet is supported by a table extension.
SawStop PCS31230-TGP252 10 in. 3HP table saw is a high performance cabinet table saw that features a durable cast iron table, 44 x 27 in. of total space, and is super durable, making it an ideal table saw for professionals. In addition to its industrial capabilities, this SawStop table saw also boasts a couple other practical features including a Flesh Sensing Technology, dissipative arbor belt to prevent hazardous charges, and an easy-to-change brake cartridge.

At first glance, the Bosch 10-Inch Worksite Table Saw may seem to be nothing exceptional. However, it's powered by the best motor in its class, and it does everything well. True, the motor is a 15 amp unit like the others on our list, but it produces 4 HP where the others produce only 1.5 to 2 HP. This is a noticeable step up in a vital area! The wheeled frame is extremely helpful for moving around your shop or garage, but keep in mind that those tires aren’t heavy-duty; you have to be careful with them on a worksite littered with nails and screws.
The Bosch 4100-10 10 In. Worksite Table Saw with Gravity-Rise Wheeled Stand delivers both professional rip capacity and outstanding portability for a tool that can get the job done, wherever it is. The powerful 15-Amp saw delivers 4.0 max HP for outstanding productivity. It also incorporates soft-start circuitry for smooth but quick ramp-up to the operating speed to manage the intensity of motor start-up and minimize the possibility of tripping a circuit breaker. It includes Constant Response circuitry to help maintain speed under load, and overload protection.
You’ll also want to consider which features are most important for you. If you need extra space to work, and cut lots of larger stock, you should invest more in a saw that gives you more room. If you’re working with people who haven’t spent their lives working with professional-grade tools, or if you’re trying to meet tough workplace safety standards, you should probably spend a bit more for a unit with a skin-detection system to protect fingers or limbs.

We were impressed with the Bosch Glide Miter Saw which was revealed in 2010 and revolutionized the depth required by a saw in close quarters. Building on their solution-based approach to products, the company has finally addressed the need for a truly portable full-power jobsite table saw. The Bosch GTS1031 table saw can be carried by its single handle, which is balanced in the middle, and all accessories are safely and securely stored on-board. This was demonstrated wonderfully by none other than Jason Feldner at the 2011 Bosch Media Event, who came running into the room with the Bosch GTS1031 table saw in one hand and a GTA500 stand in the other. Weighing in at a manageable 52 pounds, and this is one 15-amp jobsite table saw that does a great job of balancing portability and raw cutting power.
Safety and precision are usually at a high level. Some models even offer a sliding table as an option to mitigate cross-cutting. Needless to say, hobbyists love the sliding feature because it saves a lot of time and most importantly – nerves. As far as the driving mechanism goes, there are three possible options – single V-belt, serpentine belt, and a multiple V-belts.
Last but not least, you need to pay attention to the dust collecting capabilities of a particular model. Portable units usually have a weak dust-collecting capacity, but they aren’t foreseen for large projects. However, all other types do feature some kind of dust collecting system. The first thing you should check is the diameter of the dust port. The larger it is, the less debris you’ll have flying around. Also, check out the vacuum requirements because some models work only with super-expensive vacuums. As you can assume, the thing that’s lacking with those models is cost efficiency. However, if you don’t have budget limitations, feel free to invest in a high-end vacuum, it makes a huge difference.
With a single cast iron trunnion system, the Delta UNISAW offers dependable accuracy, smooth and continuous operation, but also vibration free control. Thanks to the fact that it features a fifty-two inch fence system, it’s the perfect choice for woodworking pros, but also people who are just starting out in the woodworking industry, such as hobbyists. Since it also comes with an upfront bevel dial to easily fine tune the blade level, you get a striking accuracy within a quarter of a degree, ensuring precision setups cut after cut.

6. Clamp rip fence to check if it holds securely at front and rear. If rear is not clamped securely, un- clamp fence and turn rear clamp adjustment screw 6 clockwise for increased clamping. Try clamping the fence to verify if it self aligns and clamps tightly at the front and rear. Overtightening of the rear clamp adjustment screw 6 will cause the rip fence to be non-self aligning (Fig. 23). Overtightening may cause friction or “chatter” when fence is moved side to side.

The frame is also improved. Instead of the basic roll-cage on the Dewalt, this one neatens things up with an integrated sub-base. It’s a rugged rubber-like pad which serves as a bumper between the main frame and your truck bed or worksite table. Both the table and the sub base are joined to the main frame, and they provide strength at both ends of the design. As with the Dewalt, you can store your tools and accessories inside, an on hooks outside the Bosch.

Ryobi’s RTS21G comes in as the only table saw in the group under $200. It’s lightweight, reasonably compact, and we got acceptable jobsite cuts with the upgraded Diablo blade. The throat plate uses magnets to hold it in place while leaving it easy to remove for blade access. Using a threaded rod to push the height adjustment up, you’ll notice it’s easier and smoother on the way down. The stand folds up and can be Velcro-strapped to the back, though it’s a bit wobbly compared to the others when ready for action.
Makita joins DeWalt with an external riving knife release so you don’t have to reach into the throat to loosen it. We actually ran into an issue with the design because of a slightly bent plate holding the knife in place. That aside, the intent of the design is sound and should make for an an easier experience. Because of the external release, Makita screws down the throat plate in place. You should only need to get in there for blade changes if everything functions properly.
There are several types of table saws. The types of jobs or projects you plan to use a table saw for will determine which type you buy. If you want a saw you can take from job site to job site and store it easily, then you will need a table saw that is made to be portable so that it can be easily transported to the job site. Of the portable or work site table saws on the market today, the Bosch 4100-09 10-Inch Worksite Table Saw with Gravity-Rise Stand and the DEWALT DW745 10-Inch Compact Job-Site Table Saw with 16-Inch Max Rip Capacity are two of the most popular.

The power transfer system is neatly done. The model features a serpentine belt which is quiet and smooth during operation. Therefore, the level of noise is satisfactory. Precision is something that makes this model worth checking out. Whether you’re a professional or a beginner, you’ll definitely appreciate the accuracy of this model. On the other hand, with great things come great responsibilities. Don’t forget to wear safety equipment!


Ryobi’s RTS21G comes in as the only table saw in the group under $200. It’s lightweight, reasonably compact, and we got acceptable jobsite cuts with the upgraded Diablo blade. The throat plate uses magnets to hold it in place while leaving it easy to remove for blade access. Using a threaded rod to push the height adjustment up, you’ll notice it’s easier and smoother on the way down. The stand folds up and can be Velcro-strapped to the back, though it’s a bit wobbly compared to the others when ready for action.
The DEWALT DW745 and the Bosch 4100 are pretty evenly matched in having plenty of power and not-so-hot dust collection. I you’re looking for a light weight saw, the DEWALT comes in ahead since it weighs almost half as much as the Bosch. It is also the less expensive choice by far. The large work table, expanded cutting capability, and its Gravity Rise feature (with solid rubber wheels that make it easy to be rolling across rugged terrain at a jobsite) make the Bosch a Cadillac among Pintos, but, of course, that luxury comes with a price tag.
The DeWalt DWE7499GD table saw earns a third place finish in the safety category thanks to their GuardDetect technology. This doesn’t prevent you from using the saw without the pawls and blade guard in place, but it does require you to physically indicate you are aware they’re not in place. Ideally, this gives your mind one last opportunity to consciously note the additional care that needs to take place before cutting.
While your table saw is unplugged, take the time to clear and clean the work surface, removing any debris that could negatively impact the smooth path of the wood you will be cutting. Then, lower or raise the blade to where the blade gullet (the curved section between each blade tooth) is equal with the top of the piece of wood to be cut. Also, make sure that your saw's dust exhaust port is clear and open and that a bag is in place to catch any excess sawdust.
Home Depot sells around 60 models of table saws on its website, and the top models get hundreds of reviews from users. We found four portable saws with ratings of 4.5 stars or better from 250 users or more, and one contractor saw gets ratings just shy of 4.5 stars overall from more than 650 owners. Individual reviews are fairly short and include ratings for quality and value.
×