You can opt to extend the warranty coverage to 3 years, all through an external provider. We actually prefer these third-party warranties for power tools because they allow you to deal with people who are on your side, as opposed to company representatives, who can be frustrating to say the least. We think add-on coverage is a great safeguard for any cabinet table saw, and it’s a very reasonable proposition on this model.

The CNS175-TGP36 SawStop is a 10 in. contractor table saw with a 45 degree bevel and a rip capacity of 36.5 in. Other than that, we think this is a pretty cool table saw for a few different reasons. First, the price is about half of all other SawStop table saws, and we know money talks (actually, it yells)! Second, like all other SawStop table saws, it has the integrated flesh sensing technology, so you can be sure you’re going to keep all your digits. Also, it has some pretty impressive power; it’s powered by 15 A motor so you’ll be able to tackle whatever you need. The last of our favorite features is its portability. For being a contractor saw, it’s pretty easy to pack up and move around.
The DeWalt DWE7499GD table saw earns a third place finish in the safety category thanks to their GuardDetect technology. This doesn’t prevent you from using the saw without the pawls and blade guard in place, but it does require you to physically indicate you are aware they’re not in place. Ideally, this gives your mind one last opportunity to consciously note the additional care that needs to take place before cutting.
Blade guards are an important safety device and should never be removed from the saw. You want to find one that rises up parallel to the table so it is always on top of the material you are working with. The purpose of this blade guard is to protect you from the spinning blade. While some woodworkers find them annoying, the safety they provide is well worth the inconvenience.
DeWALT DWE7480 is an excellent table saw, especially if you consider its price. It’s a step up from the highly popular DW745 and slightly more expensive, but I think the larger rip capacity and higher RPM are well worth the extra money. The DWE7480 is still in the lower price region though, and unlike the DW745 you can also get this one with a stand: the DWE7480XA!
​The saw does not easily detach from the stand. Sometimes it’s beneficial to set the saw up as a bench-top saw, but the DeWALT 7491RS doesn’t come with quick release levers to accomplish this easily. In this case, you would have to use a drill to remove four screws to detach it from the stand. I wouldn’t recommend doing this unless you have to because over time the screw holes will strip.
Todd Fratzel is the Editor of Tool Box Buzz and the President of Front Steps Media, LLC, a web based media company focused on the Home Improvement and Construction Industry.He is also the Principal Engineer for United Construction Corp., located in Newport, NH. In his capacity at United he oversees the Residential and Commercial Building Division along with all Design-Build projects.He is also the editor of Home Construction & Improvement.

Our table saw review quickly showed that today’s portable table saws are light-years ahead of the small-saw offerings from a decade ago. They feature big-capacity cutting, greatly improved safety features and attached stands for easy setup. And saws in the upper price range rival stationary saws in accuracy and quality of cut. We limited our review to saws that included a stand with wheels and ones that could rip at least 24 in. wide, only the best table saw for our readers!


The riving knife and blade guard actually have a quick-release so you can easily remove it. This is important because, in the past, these elements were so hard to install once removed people would simply leave it off. Now that there is a quick-release feature it makes it much easier to put back on and avoid the involuntary donation if OSHA decides to visit the job-site.
More expensive models also have more efficient drivetrains, which means they achieve a higher cutting speed for smoother, faster, and trouble-free cuts. Plus, their innovative belt designs and calibrated trunnion supports make the whole cutting experience smoother, quieter, and simpler. You’ll also pay extra for innovative safety features like skin detection, paddle power switches, magnetic switches, and thermal overload protection.
We had a number of these saws – and I bought one for my own use (travelling to my kids houses and for garage use) since my old Unisaw with sliding table isn’t exactly portable. My take on the blade – is that the old 40T one (Bosch CBT1040A) was not worth anything much – so the change to a 24T blade can’t hurt (zero time anything is still zero). They generally bundle saws with cheap blades to keep the overall price down – but when I was buying in many multiples – I would have been happy for $10 off each if I had a “no-blade” option.
The Grizzly, like the other cabinet models you’ll see here, requires a 220V power supply. If you’re a professional woodworker, you probably already have a 220V hookup. If you’re a home woodworker or DIYer, you’ll need to have one installed, if you haven’t already. It can be an expensive installation, so factor in the cost when you consider how much you’ll spend on your new saw.
The Delta 36-L552 is the right cabinet table saw for boat building cabinet making and also woodworking. It features a fifty two inch Biesemeyere fence, speedometer style scales and also dual crank (up-front) controls with locking cams. Taking a closer look at the inside of the Delta 36-L552, we find a powerful 5 HP motor rated at 220V which is perfect for cutting engineered products such as melamine, MDF, but also hardwoods.
If height adjustments were standardized, we could expect each saw to make them nearly identically. Taking a look under the hood, we discovered several different methods—each with their own effect. Most of the saws employ a bevel gear system that provides smooth and reliable performance. We noticed that many used solid metal gearing, but Bosch used plastic for both the 4100 and the REAXX.
The miter gauge gets an “its fine” grade. Ok to support a narrow piece for a crosscut, but not long enough to do much more than that. I upgraded to an Incra miter 1000SE and never looked back. Although a crosscut sled is pretty easy to make (and I highly recommend getting one) I picked up an Incra Miter Express sled for real cheap at a garage sale, so I am happy to use that.
A lot of the modern table saws nowadays will have a dust collection port where you can hook up a vacuum or extraction system to it. We would always recommend that you purchase a table saw with a dust port, always check the size of the port to make sure it fits with either your vacuum or your extraction system, or you can always modify something to make them fit.
Below we’ve included the current pricing (at the time of publishing this article). Pricing includes the cost of the stand and ranges from a low of $349 for the Hitachi to a high of $1,299 for the SawStop. The lowest price isn’t always the best in our opinion, we’re looking for the best value.  The Hitachi is an incredible deal at $349 and our top pick for price and value for a saw that has lots of power, a rack & pinion fence, and a solid stand.

The throat plate is the removable piece surrounding the blade that sits flush with the table. Removing it gives you the ability to access the blade for removal or riving knife adjustments. The narrower the blade clearance the better for two reasons. First, it helps keep material from falling into the blade area or lodging between the blade and throat plate. Second, it gives you material support very close to the cut to help reduce tearout as the blade exits the cut.
The DEWALT DW745, due to its smaller size, does not have the capacity to use a stack of dado blades (blades designed to be stacked together to make wider cuts, grooves, and notches). It has also been noted that the plastic miter handle is a weak point, and it limits accuracy. There are no available table extensions. It does, however, come with a three year manufacturer’s warranty.
The blades are categorized according to number of teeth, diameter, arbor size, kerf size, application and speed. They can also be divided by material. Regular commercial table saws are 10-inch or 12-inch. Teeth usually number from 24-80. Many blades are tipped with diamond, carbon or carbide. This lets you cut through more than just wood. You will also need to think about the tilt of the blade. They are available in left tilt or right tilt. With a left-tilting hybrid or cabinet saw, the motor cover can get in the way of the sliding table. Router table extensions don’t work well on left-tilting saws. 
The large cutting table surface of the Bosch 4100-09 Worksite Table Saw is roomy enough to handle large work pieces, giving you a ripping capacity of 25”. This is a really great feature if you plan to use the saw to rip solid or plywood panels, or other large materials. I use my table saw primarily for ripping sanded plywood panels for use in cabinetry, and many of my projects would be impossible with a smaller capacity saw. The rip fence glides across the saw cutting table, so you can actually use it with one hand, and locks in place for safety and accuracy. The DEWALT DW745 Job-Site Table Saw offers a 16” cut, considerably smaller than the Bosch. It is perfectly adequate for most application, such as ripping dimensional lumber and small trim applications. The type of materials and work pieces you expect to be cutting are a determining factor in your choice of table saws. If you plan on tackling any large scale projects in the future, the rip capacity of your saw is definitely a feature that you should take into consideration.
Along with thinking about how the table saw will be used now, it is important to also consider how you will be using it in the future. Will your usage increase or decrease? Many woodworkers may turn a hobby into a fulltime profession if they are talented at what they do. Why are these considerations important? Because they will give you better insight into the kind of money you should spend on your table. If you are going to go into business for yourself in a year or two, spending the money for a high-quality table now is a good idea. It will save you from having to buy another table in the future to accommodate your new needs as a business rather than just a hobbyist.
The saw’s table measures 29 x 21.5 inches which makes this unit suitable for the fabrication of large sheets of material and large wood stock. The table is made out of aluminum and is really smooth which means you will be able to slide even the largest pieces in with very little effort. Still, for extra safety, I would recommend the optional extensions when ripping longer workpieces.
If the fence and the miter slot were closer together at the rear of the saw, the dial indicator has a negative reading. If the blade and the miter slot were father apart at the rear of the saw, the dial indicator showed a positive reading. A negative reading meant that the materials being cut might be subject to being pinched and a kick back more likely to occur.
Patrick – Thanks for the feedback. Trust me, I wish we could spend more time on every aspect but we spent hundreds of hours as it was. I can tell you that the rack and pinion fences are much better than the standard fences of the past. Our entire group felt strongly that we’d prefer the rack and pinion on all the saws. We felt the Ridgid and Delta fences were the least impressive of the standard type.
The larger the motor, the higher the voltage as well, usually 240V. In some cases, you may be lucky and have a garage or workshop that’s wired for 240V, so that is why it’s very important that you check this prior to getting the table saw. In terms of the material thickness it can handle, it’s a minimum of three inches. One thing to bear in mind is that safety is an essential consideration with these saws and that’s because the powerful motors are prone to higher kickback.
Bosch engineers deserve kudos for the Gravity-Rise stand, and it’s a design some other manufacturers should emulate. Twist one lever, and the sturdy, steel frame folds up or down fluidly to convert from sawing to transport or storage. Eight-inch wheels and lugged rubber tires make this base easy to steer overland or pull up steps. Plus, the base’s stance is wide, giving it sure footing if you are pushing long planks or heavy sheet goods through. It will not tip. But, the stand when erected sets the saw’s tabletop quite high, at 38-1⁄2″. Shorter users may find this to be a bit too tall for comfort.
The Bosch will deliver a whopping big 25” rip, where the DEWALT maxes out at a 16” rip. Again, if you like the other features of the DEWALT better than the Bosch, this larger rip capacity might not sway your buying decision one way or the other. Personally, i would lean towards bosch, but that’s just me.It truly is the best portable table saw on the market today.

If the blade you purchase has a .092” kerf (i.e. Irwin Marathon 80T, FreudLU83R010) you will most likely have issues with binding on the back end of the cut. To be safe, find a blade that has a kerf of around .098” (i.e. Freud Avanti TK905 50T) and this should take care of the problem. You should also take note that every blade Bosch makes should also work with the Bosch 4100-09.

When I moved to a new home my shop area was radically downsized to half of a two car garage. In my former shop I had a 10" contractor's table saw for over 30 years. I really loved that saw but knew I was going to have to get a smaller saw. I reluctantly purchased the Bosch 4100-09 10" jobsite saw not expecting much. Wow was I wrong. I've had the saw for about a year and a half and use it daily to build medium to smaller sized projects ( boxes, trays, hanging cabinets, end tables). Right out of the box the saw performed well, I had my doubts about doing fine cabinet and furniture work but it is up to the task. I added the TS1002 outside table which is a necessity for larger boards. I also purchased the TS 1007 dado insert. The saw accommodates my freud 8" dado stack up to 1/2" which is sufficient for me. I use only thin kerf blades with a stabilizer and I've had no trouble ripping up to 1 1/2" hardwood. I do have to take it slower than on my contractor's saw but I
The DeWalt, Bosch and Ridgid saws have strong stands that are easier to set up, sturdy fences that lock down parallel to the blade every time, and smooth-operating blade controls. If you’re a contractor or an avid DIYer who just likes top-quality tools that feel good and last a long time, we think the extra few hundred dollars is a good investment.
Plus, the machined aluminum table is our favorite on the market right now. It also has a smarter motor system than either of the Dewalt’s, thanks to a soft start and automatic speed control to ensure smooth cuts. However, it’s the slowest of the pack, and it doesn’t have quite as good a fence as the yellow competition. We think it’s a great choice for pros who are concerned about accuracy, but can’t spend lots of money on their unit.
Welcome to the heart of this website – my selection of the best table saws for several specific needs. You see, it’s impossible to select only ONE as the best for all purposes because a table saw should be carefully tailored to your needs. There’s no point in buying a complex cabinet saw if you’re a beginner, you’re probably better off with a solid benchtop saw. The same goes if you’re a professional, only the other way around.
Though you’ll still want to wear safety gear when using this table saw, it has safety features that will keep you safe too. One of those features is an emergency stop. One touch of the bright green power button brings the motor to life, but when you lift up on the emergency stop that surrounds the power button, you can stop the motor in its tracks. This button has a convenient design that lets you hit and lift it with your leg or knee too.

The accuracy and safety of any given saw is dependent upon the blade being parallel to the rip fence. Since we tested the amount of difference in parallelism between the saw blade and the miter slot in the previous test, we need only to see if the miter slot is parallel to the rip fence to see if the saw has a parallel relationship between the blade and the rip fence.
Plus, it’s simply a great table saw in its own right. It’s powerful, efficient, and quiet. It cuts through all kinds of stock smoothly and easily, and the dust collection system helps it clean up after itself. Previous buyers who upgraded to this one said that the transition from their old cabinet units felt like switching from a family sedan to a sports car. We recommend it to anyone looking for the absolute best quality, for small to midsize pro shop work or the passionate home woodworker.
The RK7241S has two sturdy tubular legsets that fold down and lock, and one becomes a convenient handle for transport. The stand stayed put during heavy ripping operations, and lawnmowerstyle wheels make the tool easy to roll. But, once set up, you have to drag or lift the saw to move it, unlike other portables that keep the wheels on the floor during use.
Along with thinking about how the table saw will be used now, it is important to also consider how you will be using it in the future. Will your usage increase or decrease? Many woodworkers may turn a hobby into a fulltime profession if they are talented at what they do. Why are these considerations important? Because they will give you better insight into the kind of money you should spend on your table. If you are going to go into business for yourself in a year or two, spending the money for a high-quality table now is a good idea. It will save you from having to buy another table in the future to accommodate your new needs as a business rather than just a hobbyist.
Another excellent choice for the hobbyist or at-home handyman, the SKIL 3410-02 10-Inch Table Saw is a great value, giving you a durable build and quality performance at a wallet-friendly price. It doesn’t have the same brand recognition as some of the more expensive options on this list, but reviewers love this machine and say that it’s perfect for woodworking and DIY projects.

Contractor saws weigh quite a bit more than portable saws, averaging between 150 and 350 pounds, but are still somewhat portable. They have a heavier, cast-iron table top, and a motor that is usually more powerful than a jobsite saw. Even so, they’re within prices affordable for more committed hobbyists. Contractor saws can range between $800 and $2,000. They’re good for basic cutting tasks, as well as making home furniture and cabinetry work.
post-template-default,single,single-post,postid-5859,single-format-standard,mkd-core-1.0.2,ajax_fade,page_not_loaded,,table saw theme-child-ver-1.0.0,onyx-ver-1.4.1,vertical_menu_enabled, vertical_menu_left, vertical_menu_width_290,vertical_menu_background_opacity_over_slider vertical_menu_background_opacity_over_slider_on,smooth_scroll,side_menu_slide_from_right,wpb-js-composer js-comp-ver-4.7.4,vc_responsive
From there, the rest of the saws created a top tier of cutting power that wasn’t mind-blowingly better, but definitely noticeable. It took many cuts back and forth between saws to determine which came out ahead of other because they are so close to each other. Bosch’s REAXX took third place overall with SawStop ever so slightly ahead. Part of that simply came down to the fact that SawStop was a little bit smoother cutting. Coming out on top was Ridgid. There was noticeable vibration compared to Bosch and SawStop here, but it was able to muscle through each cut a little bit better than the other two.
It’s compact. This one is just over two feet in either direction, and just under 14 inches high. It’s easy to fit in the back of a truck, or even on the passenger seat next to you on the way to your jobsite. It’s light, too. Buyers loved how easy this one was to carry around, especially home DIYers who had to set up and take down their units frequently.
Speaking of safety, this particular model offers a satisfactory level of it. First of all, the tool-free adjustments come in handy if you’re in a middle of a project. In case you need to make a quick adjustment, you don’t have to stop whatever you’re doing and commit your attention to fine-tuning. Instead, you can do it on the go, without any additional tools. Furthermore, the convenient guarding system keeps your fingers and hands safe at all times. Don’t forget to wear protective gear; it can make a difference between life and death.
×