When you’re thinking about build quality, you should consider how often, and how intensively you’ll be using your portable table saw. The more you’ll use it, the more you should invest in a sturdy unit that’s built to handle all that use. If you’re only an occasional DIYer, on the other hand, you can probably stand to have a few more plastic parts on your unit, since you aren’t going to be putting it to the rest as often.

Table saws can pose a serious risk of injury, since part of the spinning blade comes up above the surface of the table where it can come into contact with the user's hand as it guides the wood. Thanks to voluntary safety standards introduced by Underwriters Laboratories (UL) in 2007, pretty much all table saws now come with blade guards that minimize the risk. Modern guard systems are easier to remove and replace as needed – an important feature because inconvenient blade guards are apt to be left off the saw.
The JET ProShop Table Saw offers features you The JET ProShop Table Saw offers features you expect from a high-end cabinet saw in the compact design of a contactor-style machine. The transparent blade guard has independent leaves and the quick release riving knife reduces chance of kickback. A low profile riving knife is included for non-through cuts.  More + Product Details Close
Look for guards with two independent panels on each side of the blade, so that while you work on one side, the other side keeps dust in the vacuum system, rather than flying off to the side. High-end cabinet units also have splitter and guard systems which are molded like the internal shrouding to amplify suction, so you should look carefully at those features.
For benchtop and jobsite saws with direct drive motors, the motor RPM is the blade RPM. If you’re considering a contractor or cabinet saw, it’s a different story. In any event, Pro table saw RPMs generally range from 4000 – 5000. Don’t let numbers on the lower side dissuade you. There’s a limit to how much power you can draw and each manufacturer has to decide how they’ll channel it between blade speed and torque. So higher isn’t necessarily better.
All seven saws in the best table saw testing have some kind of dust control. The Rockwell saw has a completely enclosed motor compartment with a large dust bag that attaches under the saw to catch sawdust. The remaining saws have a shroud around the blade and a 2-1/2-in. port on the back for attaching either a bag or a vacuum cleaner. None were perfect, but at least you can catch most of the sawdust. The Craftsman and Ryobi also include a dust bag that attaches to the vacuum cleaner port.
The DeWalt, Bosch and Ridgid saws have strong stands that are easier to set up, sturdy fences that lock down parallel to the blade every time, and smooth-operating blade controls. If you’re a contractor or an avid DIYer who just likes top-quality tools that feel good and last a long time, we think the extra few hundred dollars is a good investment.
As we already said, people tend to remove the safety elements to speed up their projects. Needless to say, it’s a huge mistake. Those things are there for a reason, and they should remain installed at all times. As soon as you mingle with the parts, you’ll jeopardize the integrity and your own safety. Even the best table saw cannot protect you enough if you mess with the parts on your own.
More expensive models also have more efficient drivetrains, which means they achieve a higher cutting speed for smoother, faster, and trouble-free cuts. Plus, their innovative belt designs and calibrated trunnion supports make the whole cutting experience smoother, quieter, and simpler. You’ll also pay extra for innovative safety features like skin detection, paddle power switches, magnetic switches, and thermal overload protection.
Electric brakes in the saw is an important feature as helps the saw in reversing electricity in the motor, thus contributing to a precise cut. It is highly recommended that when you are buying a saw choose the one with on and off switch. The switch should be easily accessible to make work better and more efficient. In addition, the switch should have a cover. This will keep you from accidentally turning the saw on and damaging your work area or cutting yourself.
From there, the rest of the saws created a top tier of cutting power that wasn’t mind-blowingly better, but definitely noticeable. It took many cuts back and forth between saws to determine which came out ahead of other because they are so close to each other. Bosch’s REAXX took third place overall with SawStop ever so slightly ahead. Part of that simply came down to the fact that SawStop was a little bit smoother cutting. Coming out on top was Ridgid. There was noticeable vibration compared to Bosch and SawStop here, but it was able to muscle through each cut a little bit better than the other two.

Service can be expensive on these models, so you should see if the company will be covering repairs, of if you’ll be expected to foot the bill. Add-on plans are a great way to minimize your liability if something goes wrong. By purchasing a third-party warranty, you can have a much better customer service experience. The warranty provider will deal with the company for you, so you don’t have to negotiate or deal with frustrating runarounds.


You will agree that your ability to hold, controlling and manipulating the saw largely depends on your strength. Since small table saws are lightweight, you should go for a powerful table saw so as to avoid fatigue during small jobs. This also means that if you are working in a forest for a whole day the light weight is of great importance it also helps reduce fatigue. When shopping for chainsaws ensure the saw balances well in your hand. You should also ensure that you can easily shift the saws grip from hand to hand without losing its balance.


The DEWALT DW745, due to its smaller size, does not have the capacity to use a stack of dado blades (blades designed to be stacked together to make wider cuts, grooves, and notches). It has also been noted that the plastic miter handle is a weak point, and it limits accuracy. There are no available table extensions. It does, however, come with a three year manufacturer’s warranty.
Table saws cut more or less the same way as a circular saw (covered in their own report): a round blade, usually 10 inches in diameter, spins as it works its way through the wood. The main difference is that the blade is fixed in place, sticking up through a gap in the table, and the operator moves the wood past the blade instead of moving the saw itself. Table saws support and guide lumber and wood panels as they pass over the spinning blade, making it easier to make accurate repeat cuts than with a circular saw.
As accidents and injuries are common when using large power tools like this one, it’s important that you look for safety features such as a dust collection system. Inhaling the sawdust that comes off the wood can make you sick, but this system does a good job of removing the dust from your work area. The collection port itself has a convenient on the cabinet too.
More power is also associated with more control. More control also gives you the ability to cut tougher materials. Furthermore, more control allows you to use bigger blades with ease. For instance, a 1500W of the motor will result in swift movement of the blade as it spins. High RPM of the blade gives the user a greater chance of achieving accurate and precise cut. So, when shopping for a table saw, look out for a skill saw with the higher motor rating.
I build guitars in a small shop; I need my saw to be accurate, repairable and easy to store or move. I love this saw! I use it for everything from cutting down stock to slotting my fretboards. It gets out of the way, it came dead on square, and the dust collection works pretty well with a shop vac and great with a high volume dust collector, with an Incra miter fence it makes perfect, repeatable, and accurate cuts. After I had owned it for over a year the plastic lever on the riving knife broke - I called Bosch and they "goodwilled" me a new riving knife assembly (with an upgraded metal lever) via express mail. No charge and fast, friendly service - they didn't even ask for a serial number or proof of purchase. I'd buy this saw again in a minute - all tools wear out or break at some point and I really like that the company stood behind this one and got me up and running again in a hurry. I also love all the safety features - riving knife, anti-kickback pawls, large easy-to-reach power button, nice push stick, and a dust collection port that is positioned out of the user's way.
Makita joins DeWalt with an external riving knife release so you don’t have to reach into the throat to loosen it. We actually ran into an issue with the design because of a slightly bent plate holding the knife in place. That aside, the intent of the design is sound and should make for an an easier experience. Because of the external release, Makita screws down the throat plate in place. You should only need to get in there for blade changes if everything functions properly.

Skilsaw produced the only worm drive table saw in our group and we had high expectations, especially given the high RPM count. In the end, the power is definitely at the professional level and settled in tied for fourth overall with DeWalt. This was the lightest, most compact saw in the group. Like DeWalt, the lack of an outer housing leads to more efficient cooling but drops storage for an extra blade.

These tests and evaluations are very difficult, take a lot of time, and ultimately limited in scope as we’re not a professional testing company and we’ve got limited time to evaluate the tools. We cannot do longer term testing that would shed light on durability and we can’t possibly test every application that you might use of one of these saws for. However, we feel comfortable that all the table saws in this Head-to-Head are good saws and our testing helps bring to light pros and cons for each saw.
We compiled this set of data and created a ranked set of results by assigning a 1-2-3 rating to the relative values of the test measurements. Then we ranked the saws for overall as-manufactured table flatness. As a point of interest, a typical sheet of copy paper is approximately .004 inches thick. Flatness measurements varied from 0.0 to .09 inches.
The DCS7485T1 60-Volt MAX 8-1/4 in. table saw The DCS7485T1 60-Volt MAX 8-1/4 in. table saw is maximized for accuracy capacity and runtime. The brushless motor delivers the power to cut all common materials the rack and pinion fence allows for fast easy adjustments and provides the capacity to rip 4x8 sheet goods. The DCS7485T1 comes with 1 ...  More + Product Details Close
Other than getting a cutting tool that will lighten your work, investing in an item that will ensure you are satisfied by its construction, performance and longevity are the desire of every customer. DEWALT understands better the needs of various customers and has been in the business for a long time. The many year’s experiences have given the company trust in customers. Therefore, they manufacture strong tools with high performance and back them with a sustaining warranty. The table saw is designed with a portable style for use in any room comfortably.  15 amp, gives a powerful and consistent performance to ensure you don’t have pending jobs on various days. The large rip capacity makes it easy for you to cut even large materials comfortably. When using this saw, all you need is to keep your eyes open, it has a guide system that will provide accuracy and precision in your work automatically.
×