As far as performance, the fence could be a bit better in its locking in – square front to rear – but you get used to being able to set it square and use the rear adjustment knob so that it stays put. Some folks have complained about motor burn outs – but having experience now with 17 saws – over 6 years or more – I haven’t encountered the problem (maybe we’ve been lucky?)
TBB used the same iGauging 35-125-4 digital dial indicator to measure the accuracy of the as-delivered factory fence to the table miter slot. We started by placing the fence in a locked position about 1” away from the blade on the opposite side from the miter slot. We adjusted the throw of the dial indicator so that we took the readings on the indicator, as before, in the middle of the indicator’s range of movement.
From there, it’s all about flesh detection. The REAXX wins out over SawStop in this category thanks to quicker recovery, a two-shot activation mechanism ($99 per cartridge, $49.50 per shot), and keeping the blade from damage. The initial saws to go out also come with a code to get an extra cartridge for free when you register the REAXX. Like I mentioned earlier, the unknown is still the actual reaction time compared to SawStop.
We cannot emphasize enough how important it is to think about safety at all times while using these tools. Even the slightest mistake can make a difference between life and death. The worst part is the fact that it usually happens in an instant, leaving you no time to react at all. Therefore, whatever you do, don’t forget that there’s a thin line between you having ten fingers at one moment and 8 in the next second.

The design is not bad. The height of this particular table saw is around 35 inches. While some people don’t mind it, we think it could have been designed better. However, the best thing about the design is the fact that you can get both contractor and cabinet style table saws in one unit. Dust control is well-designed. The large 4-inch dust port offers a no-hassle setup, especially with vacuums of lower quality. In simpler words, you don’t need to purchase a super-expensive vacuum for this particular unit; any affordable one should do the job well. 

The Bosch will deliver a whopping big 25” rip, where the DEWALT maxes out at a 16” rip. Again, if you like the other features of the DEWALT better than the Bosch, this larger rip capacity might not sway your buying decision one way or the other. Personally, i would lean towards bosch, but that’s just me.It truly is the best portable table saw on the market today.
Sadly, you will have to sacrifice in a few key departments for all that portability and convenience. Portable table saws are the worst choice for cutting larger stock, especially if you don’t have an extension table to add on. They’re also the least powerful sort of table saw, so you shouldn’t plan to cut thick stock or hardwoods on them regularly. Thanks to their light build, portable units are the loudest of the bunch, and their dust collection is usually less than impressive. However, if you’re moving around a lot and need to do rips in the smallest possible space, these are your best friends.
Other features include a battery-powered laser for lining up cuts. I found it to be pretty dim under bright shop lights and not lined up correctly with the blade. It is non-adjustable. A pullout rear extension provides some added support for long rip cuts. Rockwell also offers a couple of unique accessories: a sliding miter table ($179.99) and a power planer-style “Finisher” ($129.99). It mounts on the saw for flattening board edges.
Like most other product review sites, ConsumerSearch is supported by a combination of commissions on the sale of the products we recommend and ads that are placed on our site by Google. If you find something you like, you can help support us by clicking through and buying the products we pick. Our editorial process is independent and unbiased; we don’t accept product samples, requests for reviews or product mentions, or direct advertising.
Ergonomics is the science of designing and producing tools that improve a worker’s efficiency while reducing discomfort, fatigue, and risk of injury. Ergonomically enhanced tools can include helpful features such as angled handles, riving knives, safety switches, and non-slip coatings. Whether you’re shopping for ergonomic tools or just trying to select the right one for the job from an existing collection, the key things to consider are whether or not the tool eases your work and prevents you from straining in ways that could lead to injury. Ergonomic guidelines in tool design can help maximize human performance on the job by making the job easier for the worker, improving safety and decreasing injuries.
You can use these saw to cut plywood and other sheet goods, but their compact size makes this a challenge—and a potential safety hazard, if you don't have an extension table, rollers or a human partner to help support the wood on the infeed and outfeed sides. Stick with a circular saw for larger plywood rip cuts, but both of these saws can be workable backups (provided you don't need to rip widths of more than 16 or 18 inches.)
Other than getting a cutting tool that will lighten your work, investing in an item that will ensure you are satisfied by its construction, performance and longevity are the desire of every customer. DEWALT understands better the needs of various customers and has been in the business for a long time. The many year’s experiences have given the company trust in customers. Therefore, they manufacture strong tools with high performance and back them with a sustaining warranty. The table saw is designed with a portable style for use in any room comfortably.  15 amp, gives a powerful and consistent performance to ensure you don’t have pending jobs on various days. The large rip capacity makes it easy for you to cut even large materials comfortably. When using this saw, all you need is to keep your eyes open, it has a guide system that will provide accuracy and precision in your work automatically.
Overall, the Dewalt's combination blade leaves a slightly smoother finish, but both brands' general purpose construction blades are good enough to start off with. Cross and rip-cut edges were fairly smooth, but users who plan to cut down a lot of plywood will definitely want to invest in a more suitable saw blade. Both saws provided ample cutting power without a noticeable difference in cutting speeds, so we're calling this one a tie.
To learn about how table saws perform in real people's homes, we consulted owner-written reviews at retail sites like Amazon, Home Depot, Lowe's, and Sears. User reviewers don't have the breadth of experience that many experts enjoy, but they can provide keen insights on the model they bought, including things that might not crop up in the relatively short time professional reviewers have to spend with a given saw.
The JET ProShop Table Saw offers features you The JET ProShop Table Saw offers features you expect from a high-end cabinet saw in the compact design of a contactor-style machine. The transparent blade guard has independent leaves and the quick release riving knife reduces chance of kickback. A low profile riving knife is included for non-through cuts.  More + Product Details Close

By the late 18th century, a new tool had been created that would eventually have the sawyers out of work: the circular saw. These early rotating saws were powered by a range of different forces, often including running water or wind, and sometimes driven by animal power. By the early 1800s, the sawmill was replacing the saw pit and its hardworking manual sawyers.
I just purchased this saw last week. It took several hours to assemble. everything was there and I had no problems putting it together. Not hard but time consuming. The first job was to rework some vertical drawers. It did a good job fence worked great as did the riving knife. Saw was quitter than I expected. overall I am very happy. The only problem was that I had to weight a couple of extra days for delivery due to all parts not arriving at the same time.

The thing you might not like about it is the non-flat table top. Many people find this downside as quite a burden, especially if you’re processing perfectly flat wood. Also, the protective coating on the top side of this model is pretty subpar. In fact, it barely protects anything. Consequently, it will peel off quite quickly. As far as the price goes, it’s okay, but it could have been a bit cheaper.

If you’re going to have a quality product, you need a fence system that’s perfectly square to the table so your cut is perfectly parallel to the edge. Obviously, framers have a bit more leeway than jobsite carpenters and there’s plenty of variance in fence quality. Cheaper saws have fences that can easily move out of square as they slide along the surface of the table. Avoid these if you want quality results. The fence system needs to be easy to keep square to the blade.
The blades are the primary factor to consider when shopping for a saw as they hugely determine the performance of your table saw. The blades will only be effective if they are set at a correct depth of cut. The table saw will also perform best if only the correct blade for the cut is fitted, as a proper blade will enable you to achieve a precise and smooth cut. When purchasing a blade, go for the one with a correct setting blade. Consider the cutting depth also as this will determine its suitability for the job. You should also ensure that the table saw is equipped with splinter guard as this will help in minimizing splintering of the board’s top surface. Splinter guard also enhances accuracy because when it is lined up at the start and finish mark the saw will cut with precision. A suitable table saw should also have a 20mm arbor as this guarantees the stability of the blade and hence, safety in the workplace.
Like the Bosch, this Dewalt comes with a rolling stand. It’s convenient to set up and take down, since you can do it without helpers or tools. It rolls like a dolly, and opens into a nice, sturdy table. We especially like the splayed legs, since they lend the whole thing a bit more stability than the Bosch version. Unlike the Bosch’s stand, the Dewalt’s has semi-pneumatic tires which won’t ever go flat.
Though this table saw will arrive in multiple pieces, Jet includes all the instructions and help that you need to assemble the cabinet and all other parts. The cabinet itself has an enclosed design that keeps the motor and all other components safe from the dust in your workshop and any debris flying around. You also get four legs that attach to the base of the cabinet, which lifts the saw higher in the air to reduce back pain caused by bending over the table.
Though this table saw will arrive in multiple pieces, Jet includes all the instructions and help that you need to assemble the cabinet and all other parts. The cabinet itself has an enclosed design that keeps the motor and all other components safe from the dust in your workshop and any debris flying around. You also get four legs that attach to the base of the cabinet, which lifts the saw higher in the air to reduce back pain caused by bending over the table.
If you’re looking for a machine with high capacity, the SKIL 3410-02 has a 3.5-inch cut height with the ability to cut through four times the material on each pass. The consensus among reviewers is that, for such a low price, you end up compromising on miter gauge and saw blade quality. Luckily both of those things can be replaced if you so choose.  
Hybrid saws will often match in terms of power but very rarely have the stability and durability of a cabinet saw, so often they work well in a home work shop where you can add extra stands etc to help. One thing to think about though is that because they won’t be as stable this can often compromise on the quality of the cuts, this is something you must think about when deciding. Read More
The DEWALT DW745 and the Bosch 4100 are pretty evenly matched in having plenty of power and not-so-hot dust collection. I you’re looking for a light weight saw, the DEWALT comes in ahead since it weighs almost half as much as the Bosch. It is also the less expensive choice by far. The large work table, expanded cutting capability, and its Gravity Rise feature (with solid rubber wheels that make it easy to be rolling across rugged terrain at a jobsite) make the Bosch a Cadillac among Pintos, but, of course, that luxury comes with a price tag.
×