This is a truly great saw, except that it is really tough to adjust the blade and rip fence for parallel. Once adjusted though, it is a fine piece of engineering. What I like best is that the saw is built for the job site. It is extremely beefy, but no too heavy. In my opinion, it strikes a nice balance. Its cart stand is the best in the industry, bar none. Once adjusted, the saw returns to its settings extremely well. It is obviously built for the long haul, and should last a contractor many years. I would definitely purchase this saw again. Now with the things that I wish were better. First, adjusting the blade for parallel is just plain hard. Mine was out from the factory by 4 thousandths. It is a trial and error process, and the instructions suck. Here's what to do: 1. Loosen the four screws indicated in the instructions. Starting from behind the saw, center the blade housing in the rear left to right as best you can, then tighten one screw not quite snug (you want the housing to rotate on this screw when you adjust the front). Next move to the front of the saw and loosen the lock lever for blade angle adjustment (the housing won't move unless you do). Now, begin experimenting with holding the housing at 90 degrees with one hand while sliding the housing back and forth with the other until square. When you think that you are close, lightly tighten one of the front housing screws. Check for parallel (look for videos on how to check a table saw blade for parallel), then tighten the blade angle adjustment lever. With these screws and the lever tight and locked, check again for parallel. If it is still good (I got it to 1/1000 inch of parallel), then lock all the screws and check one more time, if it's still good, then you are done with blade housing adjustment.
It’s the best of the three at keeping your shop clean. The SawStop has a blade guard and arbor enclosure that’s engineered and sculpted to maximize vacuum suction at the cutting edge. Plus, the guard hugs tightly to the blade, and like the Jet, opens at each side so that whichever way you’re cutting, dust goes down the vacuum chute instead of off to the side of your workspace. It’s lab-tested to be up to 99% effective, and it’s certainly the most impressive dust collection system we’ve seen to date.
It’s easy to use, quite safe, and most importantly – it’s a high-quality piece of equipment for a more than reasonable price. If you don’t like what you see, don’t hesitate to read some of our other reviews, there might be something of interest for you. As far as this particular model goes, it should turn out to be a worthy and cost-efficient investment. In the end, it all comes down to your personal preferences.
A 50 rpm deviation at those speeds is approximately 1% variance which is well within the tolerance we should expect from taking the readings at a precise instant of time. The meters were in constant motion and we took the reading off of a single video frame that represented our determination of no-load speeds. We report them as our instruments showed them. 1% is acceptable.

One shouldn’t expect a massive amount of storage, but being a table, it does offer some level of free space. In fact, some models even offer space for fences, gauges, blades, and other necessary equipment. Apart from that, you can always keep the necessary tools in the reach of your hands. It will make the process much easier and also a lot quicker.
With a 32½" rip capacity and motor capable of up to 4800 rpm, the DWE7491RS is more than prepared to effectively deliver 3⅛" deep cuts to thick slabs of wood. Happy customers sing this machine’s praises, reporting that it’s as sturdy as a table saw can get — plus, it’s easy to use, and assembling it is a cinch. They do however note that workers looking to produce finer cuts should seek out a replacement blade since the one provided is more suited for fast, rough work.

The dual extension tables (rear and side) offer 50% more table space than most rectangular units. We also appreciate that Grizzly have put all the space under the worktop to use, with steel-frame shelving built in as standard. You can use it for scrap wood, tools, and accessories: you can even fit a full tool chest under there! It’s a good space-saving touch for busy shops.
In layman’s terms, a miter gauge is a device that allows users to set up the angle of the material being cut with a table saw. And while most table saws come with built-in miter gauges, others, well, don’t — which is why the Kreg KMS7102 Table Saw Precision Miter Gauge System is invaluable. Whether you’re replacing an old, worn-out gauge or putting it to use in conjunction with a table saw that didn’t come with its own proprietary gauge, the KMS7102 is specially designed with precision in mind. After all, accuracy is vital to successful woodwork.

These are the best choice for long jobs where you’ll get yourself set up at a job site, and need a saw that enables you to make all your big, long cuts without traveling back and forth between the site and your shop. While you won’t want to move these units around frequently, they’re great for seeing a contract through to the end from the worksite.
Porter-Cable comes in as the most expensive of the value group, but also with the best overall performance in it. Of the three saws in this class, it had the best cutting power and also came in the top spot overall for height and bevel adjustment thanks to independent wheels. This may seem like a small consideration, but when you actually need to cut accurately beveled pieces, the adjustment wheel is a huge benefit over sliding the front height adjustment around.
Having only owned saws with cast iron tops this is a new experience for me. First let me note that the right side extension is not aluminum like the rest of the top. It is steel, painted to match. The entire top appears to be powder coated with a textured grey coating. No telling how durable it will be but it does allow wood to slide easily over it. Since the top is aluminum, it lets you know that by transferring all the motor noise and vibration throughout the saw. Not a big deal really but definitely different if you are used to the cast iron absorbing much of this on bigger saws.
We rotated the blade to the rear of the saw to enable the dial indicator to contact the same location of the same tooth behind the carbide portion. We positioned the dial indicator to the rear of the saw placed onto the blade and the reading recorded. If the blade and the miter slot were closer together at the rear of the saw, the dial indicator has a negative reading. If the blade and the miter slot were father apart at the rear of the saw, the dial indicator showed a positive reading.
As you would expect, the most expensive saws made slightly smoother cuts. But the difference was negligible. The only saw that struggled to make smooth cuts in the super-thick oak was the Ryobi. In more common situations, like cutting 3/4-in.-thick material, Ryobi’s cut quality was fine. We found the blades included with all the saws to be adequate for most ripping tasks. But if you want cuts smooth enough for glue joints, you’ll have to invest in a better blade.
The fact is, a table saw is designed to remove a large amount of material in a quick and efficient manner. With the volume of waste that is produced by any but the smallest table saws, a shop vacuum is not going to be up to the task. Short of purchasing a standalone dust collection system, the best that you can hope for from a shop vacuum is that it might keep some of the saw dust out of your eyes.
The first measurements we looked at with the performance testing was blade speed cutting all three of the test materials. This tests gives us a relative comparison of how much blade speed reduction the motors have under different loading conditions. In our opinion this gives us an idea of how strong the motor/gear box combination is for each saw. For each test we also recorded the “no-load” speed to capture the relative drop in rpm in the blade speed while cutting wood. We used our as-measured no-load speeds instead of the published values from the manufacturers.
It also has the highest blade speed. This model has a similar 15-amp motor to our other recommendations, but it’s geared for maximum efficiency. The result is a blade speed that’s nearly 1000 RPM better than the Bosch or the smaller Dewalt. Reviewers marveled at how powerful this one was compared to the size of the motor, which seems underwhelming from the outside. It rips right through oak, cherry, and other planks with no lag or burnout. In fact, we’re hard-pressed to find something this would struggle to cut, provided you equip it with the proper blade.
Probably one of the things that users will love most about this table saw is the solid granite surface which offers a seamless work area and excellent support. Another advantage of the Steel City 35955 is the fact that it comes with powerful magnets which allow swift changes without having to worry about using any type of tools. Since there’s a built-in mobile stand, you can easily position the saw around your shop without requiring the help of a second person.

To make our recommendations for the best table saws, and the best table saw bargains, we consulted comparison tests and single-product reviews in tool-related publications such as Pro Tool Reviews, Woodworker's Journal, Popular Mechanics, Tools of the Trade, and Fine Homebuilding. Many of these reports are several years old, but most of the models tested are still available. Most professional reviews focus on portable table saws, but we found a few that cover contractor and cabinet saws.
If you need a table saw that can travel, the Bosch 4100-09 consistently earns high marks. Reviewers praise its power, accuracy, easy setup, and easy blade changes. They also love the gravity-rise wheeled stand, which rolls smoothly and snaps open or folds flat in a single lever-activated motion. Finally, they appreciate the convenience of the blade guard system, complete with riving knife and anti-kickback pawls.
Speaking of safety, this particular model offers a satisfactory level of it. First of all, the tool-free adjustments come in handy if you’re in a middle of a project. In case you need to make a quick adjustment, you don’t have to stop whatever you’re doing and commit your attention to fine-tuning. Instead, you can do it on the go, without any additional tools. Furthermore, the convenient guarding system keeps your fingers and hands safe at all times. Don’t forget to wear protective gear; it can make a difference between life and death.
TBB measured the accuracy of the factory-set 90 degree stop by using a Wixey WR365 digital inclinometer. This device has an accuracy of 0.1 degree. We placed the Wixey gauge on the table and calibrated the inclinometer to the table by zeroing out the gauge. After that calibration, the measurements give a result that is relative to the saw table. We moved the blade to an approximate position of 70 degrees off vertical. TBB attached the gauge to the blade and used the saw mechanism to adjust the blade incline to the point at which the blade or trunnion hit the factory-set 90 degree vertical stop and recorded the measurement. TBB ran the test twice to ensure the repeatability of the measurement. In every case, the result came out to within 0.1 degree of the prior test.

Powerful cutting and portable convenience with the Delta Powerful cutting and portable convenience with the Delta 36-6022. The 1-step release stand and large wheels make it easy to move the saw to any jobsite. The 15 Amp commercial grade motor cuts through the toughest materials. UL approved 3-way guarding system with riving knife for safety and excellent dust ...  More + Product Details Close
The larger the motor, the higher the voltage as well, usually 240V. In some cases, you may be lucky and have a garage or workshop that’s wired for 240V, so that is why it’s very important that you check this prior to getting the table saw. In terms of the material thickness it can handle, it’s a minimum of three inches. One thing to bear in mind is that safety is an essential consideration with these saws and that’s because the powerful motors are prone to higher kickback.
The Bosch 4100-09 10 In. Worksite Table Saw with Gravity-Rise Wheeled Stand delivers both professional rip capacity and outstanding portability for a tool that can get the job done, wherever it is. The powerful 15-Amp saw delivers 4.0 max HP for outstanding productivity. It also incorporates soft-start circuitry for smooth but quick ramp-up to the operating speed to manage the intensity of motor start-up and minimize the possibility of tripping a circuit breaker.. It includes Constant Response circuitry to help maintain speed under load, and overload protection. The Square Lock rip fence is engineered for maximum trueness and great ease-of-use, with the fence able to easily glide along the rail for one-handed operation. The lighter GTA47W Gravity-Rise Wheeled Stand has 8 In. treaded rubber-composite tires and a single-action design for easy set-up and transport. It is jobsite-ready with heavy-duty construction. The Smart Guard System is the first modular table saw blade guard, featuring a three-position adjustable riving knife, anti-kickback pawls and non-obstructed-view barrier guard assembly. The table saw provides a 29 In. x 21-1/2 In. square tabletop with a 25 In. rip capacity for ripping 4 Ft. wide sheets goods in half.

so.categoriesWithItems ='8003,8002,8005,797,8007,696,8009,793,8011,8010,8013,750,8015,8014,833,823,825,8023,841,8017,2669,470,8041,430,8044,8047,263,8048,8050,306,8051,8053,5954,8055,8054,5957,8056,166,8059,39936,39934,39935,508,8025,5960,139891,139893,8030,566,8031,139905,8034,8033,8035,649,647,8038,661,491149,8742,505663,491151,505665,8277,143,8278,2234,8280,1224,2310,8285,8287,1222,116,6237,8292,8293,8294,8295,8296,8297,8298,8299,8300,8301,139847,139871,9022,39752,39751,39753,39754,997,8077,1022,1032,1025,8082,994,8084,139649,941,944,6471,910,8085,8087,1014,914,8090,8092,1258,8094,139687,8805,39895,39894,39896,39897,8063,224,8064,8065,5956,5959,429,39909,39908,39910,8130,5941,8131,902,1196,8137,8138,8141,8143,8142,8144,8145,1416,8148,8150,8151,1554,1422,8167,8163,8172,8174,8173,8182,8179,8183,39667,39665,469559,37938,469561,469563,37941,37940,37943,37942,37945,37944,37947,37946,3,8185,43,23,35,8191,8194,8195,1642,8196,8199,8200,139409,139411,452623,8203,8202,8204,8205,8206,8209,8210,139437,1299,1664,8216,8217,139455,139459,39703,39702,39704,108845,108843,8112,8111,8116,8114,8117,8115,8118,8106,8105,8107,8108,8109,8120,1132,8121,8122,8123,8126,6269,8221,681,8222,8220,8224,2584,8226,2575,678,662,2593,663,675,843,1699,8235,1805,8238,5980,8241,8244,8246,8247,5987,8248,8250,2614,6517,8253,8262,1307,139301,8264,187,8266,8265,8268,8267,8270,8269,8272,8271,8273,8274,39820,39819,108974,108972,468779,108975,139363,139359,139371,139369,930,928,2804,8101,919,8103,8102,39766,39765,139783,139767,108849,108848,108851,108850,140169,140167';
In terms of size, the table height from floor measures thirty four inches, with extension it measures twenty seven by forty inches and overall dimensions are 62 by 41 by 40 inches (LWH). This is simply an amazing saw and not only will you use it for many years to come, but it’s going to help you get the professional results you’re looking for in any project.
As for various accessories and attachments such as rip, miter and blade guard, these can be stored in their own specially designed hangars. If you plan on using other blades (and you probably will) there is also a well where you can store all the blades you have. In order to keep the surface of the table dust-free there is a dust collection port featuring a shrouded design which can be attached to the vacuum.
While I appreciate this review, that Kobalt job site saw is the absolute worst. Uncontrollable blade wobble, terrible fence, trundle bolts that are nearly impossible to get to without tacking the back panel off (of course that doesn’t matter when the blade won’t stay in alignment for more than a day), miter slots that aren’t parallel to each other and also taper toward the backside of the table, and a riving knife without adequate adjustments to align it with the blade. Do not buy that piece of garbage.
We evaluated the flatness of the table by measuring the flatness by placing the edge of a precision ground flat bar across the table and placed feeler gauges in any gaps to measure any difference between the ground bar and the table. TBB took measurements in four directions. As the operator faces the saw, we measured the flatness at the arbor from front-to-rear; we measured the left-to right flatness at the arbor; we measured the flatness from the upper left-to-lower right table corners; and, finally, we measured the upper right-to-lower left flatness between the corners.

The stand is collapsible and wheeled like others, but it’s not the gravity-rise style. You’ll have to use a foot to stabilize it while you pivot it up or lower it down. The lower locks are released with your feet and there’s some question about the long term durability of the releases. An open housing design has two major results – motor cooling should be more efficient but it trades off storage for an extra blade. There’s really way too much to talk about here, so check out our full review of this model.

At a compact 45 pounds, the DEWALT DW745 Compact Jobsite Table Saw is the lightest table saw in our review. The saw's portability doesn't mean that ripping size is compromised, though. Thanks to extending fence guides, you've got 20 inches available. Depth of cut is on par with many bigger machines: at 90 degrees, it's 3 1/8 inches. At 45 degrees, it's 2 1/4 inches. Power comes from a 15-amp motor with a no-load speed of 3,850 RPM. This is ample enough for serious DIY projects and light-duty construction site work.
The old designs of table saws did not have the angled capability that newer models have now with their ability to have the blades angled at 45 and 90 degrees. Before these upgraded styles, the table itself had to be tilted which made cutting extremely unsafe. The new styles that accommodate angling the blade for the beveled cuts make things much easier and safer for the user.
The DeWalt DWE7480 is a 10 in. compact job site table saw powered by a powerful 15 A motor that has top speeds of up to 4,800 RPM. When this power is paired with its 24 in. rip capacity and 47 degree bevel, this table saw is able to power through even the hardest woods with great accuracy, so you can use it for projects ranging from shelving to trim to hardwood flooring. And despite all its power, this table saw is a lightweight at only 48 lbs. No matter what woodworking project you have in front of you, this DeWalt table saw is able to power through it!
The 15-amp motor is outstanding, developing up to 4HP and operating at a speed of 3650RPM. This is not quite as pacey as the DeWalt but still more than respectable. The other advantage to this motor is that – for a table saw, at least – it’s pretty quiet. Noise isn’t such an issue out on the job site but if you’re woodworking at home, the quiet motor is a real boon.
From there, the rest of the saws created a top tier of cutting power that wasn’t mind-blowingly better, but definitely noticeable. It took many cuts back and forth between saws to determine which came out ahead of other because they are so close to each other. Bosch’s REAXX took third place overall with SawStop ever so slightly ahead. Part of that simply came down to the fact that SawStop was a little bit smoother cutting. Coming out on top was Ridgid. There was noticeable vibration compared to Bosch and SawStop here, but it was able to muscle through each cut a little bit better than the other two.

Make sure all the panels on the cabinet (including the motor shroud) are made from steel, and look for powder-coating on the panels to help the paintwork last. The adjustment flywheels, the fence rails, and the frame of the table assembly should be steel as well. The most important part to look at under the hood is the trunnion. The trunnion supports the motor, and you’ll want it to be made from solid cast iron. The sturdier the trunnion, the smoother your unit will cut.
Editor and "serious woodworker" Chris Marshall tests five "premium" portable table saws. After equipping each saw with a new Freud thin-kerf blade, he uses them to rip lengths of medium-density fiberboard (MDF) and yellow pine, as well as making long dado cuts in MDF. Marshall considers the saws' stability, cutting accuracy, efficiency, dust collection, and general ease of use to choose his top picks. Unfortunately, two of his three favorites are discontinued.

We spent over 30 hours researching and testing 10 different brands of table saws and found that maximum speed, cord length, and cut depth were most important. The DEWALT DW7480 table saw scored high marks in every category and is our top pick. This 48 pound table saw is perfect for using at home or taking with you to the job site. It has a powerful 15 amp motor and 24” rip capacity that makes it a favorite with everyone. The 2 ½” dust collection port allowed us to connect the saw to a shop vac and reduce the amount of dust that was in the garage.


The first thing people notice about this unit is its design. The rolling stand is specially designed to mitigate the transport of this saw. In simpler words, whenever you need to move it, you can do it by simply rolling the unit on its wheels. One more notable thing is the 2-inch dust collector port. You can easily connect it to a vacuum and extract the dust efficiently and without much hassle.

While I appreciate this review, that Kobalt job site saw is the absolute worst. Uncontrollable blade wobble, terrible fence, trundle bolts that are nearly impossible to get to without tacking the back panel off (of course that doesn’t matter when the blade won’t stay in alignment for more than a day), miter slots that aren’t parallel to each other and also taper toward the backside of the table, and a riving knife without adequate adjustments to align it with the blade. Do not buy that piece of garbage.


One shouldn’t expect a massive amount of storage, but being a table, it does offer some level of free space. In fact, some models even offer space for fences, gauges, blades, and other necessary equipment. Apart from that, you can always keep the necessary tools in the reach of your hands. It will make the process much easier and also a lot quicker.

The Skilsaw SPT70WT-01 is a super high quality table saw with the power to match. The Diablo blade that comes with it will cut through 4×4 without any problems at all, like a knife through butter! One of the best features we noted was the fact that there is barely any vibration, this allows to you to cut as straight as an arrow, you can really feel the build quality with this saw.It has an extremely easy to use miter gauge, just a flick of the wrist to change the angle of cuts to exactly what you want.
Some of the key factors that every woodworks person will ensure are accurate and will not compromise our performance and quality of the saw. With grizzly G0690 cabinet table saw, you will get all these in one packaging. The table saw has a riving knife that will automatically switch to action following the same blade tilts for better performance. Its made of high quality and heavy duty material to guarantee that it will last a lifetime.
×