All seven saws in the best table saw testing have some kind of dust control. The Rockwell saw has a completely enclosed motor compartment with a large dust bag that attaches under the saw to catch sawdust. The remaining saws have a shroud around the blade and a 2-1/2-in. port on the back for attaching either a bag or a vacuum cleaner. None were perfect, but at least you can catch most of the sawdust. The Craftsman and Ryobi also include a dust bag that attaches to the vacuum cleaner port.

We used the Freud calibration plate on each of the test saws to measure runout. We removed the new Diablo blade, installed the calibration plate, and raised the trunnion to its maximum vertical adjustment. Before measuring the runout, we placed a black mark on the calibration plate to give a consistent starting position for the runout test. The same iGauging dial indicator provided the test measurements, only this time, the units were set to read out in mm. TBB noticed that in the initial saws, the movements were sufficiently small to need the smaller metric units.


Bosch’s 4100-09 work site table saw is a sure win. Bosch never fails to impress us, and this table saw is no exception. It’s a 10 in. saw with a 25 in (right) rip capacity and a 47 degree left bevel. This Bosch table saw is powered by a 15A motor that reaches top speeds up to 3,650 RPM. Another feature we appreciate: its constant response circuits which continuously adapt the speed under load, giving you a continuous blade speed.

A dedicated writer and communications professional spending his days lost in the intricacies of both proposal and freelance writing. When not sharing the knowledge of both fully and self-insured medical benefits to employer groups of all industries within California, Jeff Newburgh can be found at home spending time with his family and 3 dogs, pondering the next chew toy to be thrown, while kicking back and relaxing with a nice glass of red wine.
To adjust blade height you simply operate the elevation wheel located on the front of the saw, and the angle of the blade can be set through a switch which is behind the wheel in case you want to make bevel cuts. The angle can be set anywhere between 0 and 45 degrees, and once you’ve adjusted the bevel angle it can be locked into place using the handle.
Hitachi C10RJ 10 in. job site table saw features a powerful, industrial grade 15 A motor that operates at 4,500 RPM, giving you the ripping power to cut through even the toughest woods. This Hitachi table saw has a 0-45 degree bevel and height adjustments. One of the best features is its large work table which also has a telescoping extension, allowing rip cuts up to 35 in. wide! When you pair the power of this table saw with the bevel range and table size, you’ll be able to power through any project you throw at it! Other great features include: front mounted controls, over sized controls, integrated safety switch, and a soft start function that helps decrease recoil at startup.
As mentioned, the look is similar to a hybrid with a full enclosure. Looks can be deceptive, though… The core design purpose is for this saw to stand up to constant heavy use in a commercial setting. This is not a tool you buy for casual woodworking at home.These bulky, heavy units are built to last the distance. They can weigh up to 500 pounds. You’ll get an accuracy and rigidity not available in lesser types of table saw.Other table saws call for regular adjustments. With a cabinet saw, you won’t need to do this as often once it’s set up properly. 240V motors developing 3-5HP mean there’s very little the best cabinet table saw won’t rip through with ease. Large sheets of hardwood are no problem at all.
Give yourself a reason to be proud of your job by bringing in a table saw that has what it takes to get quality cutting. Just as the name, Powermatic table saw will ensure your cutting is accurate and interesting. It has a poly-v belt, which maximizes motor efficiency and reduces vibration for noise-free performance. The table saw also features massive dust collection to ensure your working space is clean and accommodative. With 30” Accu-fence system, nothing will be impossible to handle. Additionally, the entire unit is designed with quality material for longevity. The design is also portable making it easy for you to move from one job site to the other comfortably.
While you may be tempted to skip straight to the reviews, they are a bit on the technical side and contain plenty of terms you might not be familiar with just yet. My suggestion would be to start by reading the informational articles which will provide you with a decent amount of knowledge on table saws. After that, I sincerely doubt you would be caught off-guard while reading anything in the review section.

It’s just as powerful as our other recommendations. The SawStop has a 3HP belt-driven motor, and like the Jet, it uses a tweaked multi-belt drive system to transfer maximum power from the drive shaft to the blade. That makes for as powerful a cabinet saw as any on the market. This one slices smoothly through anything you can feed into it. It also has a slightly thicker max cutting depth than our other recommendations, so it’s the better choice for sturdy stock.
Table saws can pose a serious risk of injury, since part of the spinning blade comes up above the surface of the table where it can come into contact with the user's hand as it guides the wood. Thanks to voluntary safety standards introduced by Underwriters Laboratories (UL) in 2007, pretty much all table saws now come with blade guards that minimize the risk. Modern guard systems are easier to remove and replace as needed – an important feature because inconvenient blade guards are apt to be left off the saw.

Both saws were almost equally quick to setup for use, with the DeWalt coming out slightly ahead. The throat plate, which is thicker and sturdier than Bosch's, is slightly easier to remove and reinsert. The DeWalt's blade cavity offers greater clearance, which makes locking down and loosening the riving knife easier without scraping a knuckle. Dewalt's riving knife adjustment required less wiggling and hunting to get it set properly.
Powerful cutting and portable convenience with the Delta Powerful cutting and portable convenience with the Delta 36-6022. The 1-step release stand and large wheels make it easy to move the saw to any jobsite. The 15 Amp commercial grade motor cuts through the toughest materials. UL approved 3-way guarding system with riving knife for safety and excellent dust ...  More + Product Details Close
Overall, the Dewalt's combination blade leaves a slightly smoother finish, but both brands' general purpose construction blades are good enough to start off with. Cross and rip-cut edges were fairly smooth, but users who plan to cut down a lot of plywood will definitely want to invest in a more suitable saw blade. Both saws provided ample cutting power without a noticeable difference in cutting speeds, so we're calling this one a tie.
The advent of ever better motive power that came with 19th century developments led to ever more efficient and ever more compact power saws. The first recognizably modern table saws date to the latter decades of that century. With compact and powerful electric motors developed and refined throughout the 20th century, tables saws were widely available and were both compact enough for home use, yet powerful enough for nearly any lumber ripping task.
If you are making a cut that will require your hands to get close to the blade, (within 6 inches) use a push stick or two to eliminate the chances of your hand touching the blade. If this is a big concern for you, maybe consider a saw that uses flesh detection to stop the blade. The additional cost of the saw will be instantly appreciated the first time you need it.
I also added in a bicycle saddle bag, that attaches easily to the tube frame of the saw. In it, I keep my PPE, and my Grr-ripper push blocks (great upgrade over regular push blocks). I also have a push stick made of wood that was modeled after the plastic one mounted on the back of the saw. The wood one is there now. I read too many stories of injuries after the blade touched the plastic stick, which to me is the whole point of using a stick – to avoid injuries. These things turning to shrapnel seems like a bad idea.
One thing you’ll love about the riving knife is that it allows for adjusting the table saw without using any special tools, for non-through and through cuts including, pictures frames, grooves for shelves, but also cheek cuts for furniture, rabbets and dadoes. There’s also the possibility to store different tools or anything else you may find under the tablet board and given the fact it’s expandable and convenient, it’s going to make using the Delta 36-L552 an even more amazing experience. For dust collection, the table saw comes with a bi-level dust extraction system which offers superior dust collection capabilities.
One shouldn’t expect a massive amount of storage, but being a table, it does offer some level of free space. In fact, some models even offer space for fences, gauges, blades, and other necessary equipment. Apart from that, you can always keep the necessary tools in the reach of your hands. It will make the process much easier and also a lot quicker.
Speaking of safety, this particular model offers a satisfactory level of it. First of all, the tool-free adjustments come in handy if you’re in a middle of a project. In case you need to make a quick adjustment, you don’t have to stop whatever you’re doing and commit your attention to fine-tuning. Instead, you can do it on the go, without any additional tools. Furthermore, the convenient guarding system keeps your fingers and hands safe at all times. Don’t forget to wear protective gear; it can make a difference between life and death.
×