Skilsaw produced the only worm drive table saw in our group and we had high expectations, especially given the high RPM count. In the end, the power is definitely at the professional level and settled in tied for fourth overall with DeWalt. This was the lightest, most compact saw in the group. Like DeWalt, the lack of an outer housing leads to more efficient cooling but drops storage for an extra blade.
Makita joins DeWalt with an external riving knife release so you don’t have to reach into the throat to loosen it. We actually ran into an issue with the design because of a slightly bent plate holding the knife in place. That aside, the intent of the design is sound and should make for an an easier experience. Because of the external release, Makita screws down the throat plate in place. You should only need to get in there for blade changes if everything functions properly.
If you are a woodworking professional, you'll want a cabinet saw in your workshop. These are the heaviest, sturdiest and most precise table saws, with powerful motors that require a 220-volt electrical outlet. Cabinet saws require a large, dedicated space because of their guide rails and large tables (often with big extension wings). Then also tend to have the best safety and dust-control features. Woodworkers with enough space (and money) usually make a cabinet saw the permanent centerpiece of their workshop, though a few cabinet saws have mobile bases. Cabinet saws cost $1,600 and up.
The only (somewhat) recent review of table saws at Wood Magazine pits nine 3-HP cabinet saws against various sizes of wood and plywood, fed both by hand and with a power feeder. The short version of the review available on the website names the top picks and notes areas in which all nine saws performed adequately. For full details, however, you need to check out the printed magazine.
Not everyone needs to use the miter gauge on a table saw since there’s typically going to be a miter saw around. If you do, you’ll like the positive locking detents at common angles. This saw felt like it was the weakest when pushing our 2x PT material through. Despite the ranking, it doesn’t feel under-powered – you just need to take your time. You won’t find a lot of bells and whistles on this model, but for $279, we don’t have many complaints.
The Delta Unisaw is a heavyweight in woodworking circles. It’s been on the market for years, and it’s a stalwart through and through. It has a super-powerful 5 HP motor which can blast through the toughest hardwoods and composite materials quickly. It also features one of the most precise bevel adjustments on the market, down to 1/4 degrees! It has a solid, single-cast trunnion which provides excellent vibration dampening, and an extra-heavy case iron base. In short, this is a hulking beast of a machine, and it’s easy to see why it’s been a shop favorite for years.
Table saws will use one of two different kinds of drive configurations; Direct-drive motors and Belt-drive motors. In a direct-drive motor, they will link directly to the blade itself and transfer all of the power of the motor to the blade. They tend to last longer than belt drive motors and there is no belt to replace or worry about getting worn out. Belt drive motors transfer power from the motor to the blade through a belt. In this type of configuration, the motor can be offset away from the sawdust which helps the motor last longer. In general, belt drive motors need more preventative maintenance than direct-drive motors do. If you have a belt drive motor, check the tension of your belts as well as checking them for wear periodically to ensure your continued safety.
The DeWalt DWE7480 is a 10 in. compact job site table saw powered by a powerful 15 A motor that has top speeds of up to 4,800 RPM. When this power is paired with its 24 in. rip capacity and 47 degree bevel, this table saw is able to power through even the hardest woods with great accuracy, so you can use it for projects ranging from shelving to trim to hardwood flooring. And despite all its power, this table saw is a lightweight at only 48 lbs. No matter what woodworking project you have in front of you, this DeWalt table saw is able to power through it!
IMPORTANT REVIEW UPDATE (10/4/2016): After doing some additional testing with pressure-treated lumber and heavier stock, we [initially] found some issues with the Bosch REAXX saw that we couldn’t explain—except to say that it didn’t have the power we expected for cutting through denser wood. The blade exhibited a significant drop in speed during many common ripping cuts, and it even stalled out entirely at other times. We contacted Bosch and worked directly with them to determine the nature of the issue (which appeared to have to do with the saw’s electronic speed control). Here is the initial statement from Bosch on the matter:
The weak point of this rolling stand is the base where all the weight sits. I really like the Bosch rolling miter saw stand, which is what convinced me to buy this setup. When you compare the miter saw to this table saw, it's a night and day difference. The miter saw from Bosch has thicker and larger diameter metal tubing. It clearly weights more, but it's on wheels, and has yet to show any fatigue from constant use.
And finally, they all include a blade guard that can be removed and reinstalled without tools. Because a few sawing operations, such as non-through cuts, require you to remove the blade guard, we like saws that make this task easy. The Bosch, DeWalt and Ridgid saws have well-designed blade guards that are easy to remove and reinstall. The blade guards on all but the Porter-Cable and Craftsman also have a feature that holds the blade guard in the raised position to allow better blade visibility for setting up cuts.
All table saws sold in the U.S. come with a riving knife, anti-kickback pawls, and a split blade guard. Because some cuts can’t be made with these safety features installed, they are removable. If you’re looking for a fun party game, see who of your uninitiated friends can install both correctly without a manual. While each one is different, their nature means you can use the saw without them installed. I’d be remiss if I didn’t tell you those cuts are more dangerous, so avoid it if you can.
Thanks for reading the fine print. About the Wiki: We don't accept sponsorships, free goods, samples, promotional products, or other benefits from any of the product brands featured on this page, except in cases where those brands are manufactured by the retailer to which we are linking. For our full ranking methodology, please read about us, linked below. The Wiki is a participant in associate programs from Amazon, Walmart, Ebay, Target, and others, and may earn advertising fees when you use our links to these websites. These fees will not increase your purchase price, which will be the same as any direct visitor to the merchant’s website. If you believe that your product should be included in this review, you may contact us, but we cannot guarantee a response, even if you send us flowers.
It has the widest rip capacity of the three. This one can handle materials up to 32 1/2”, which makes it ideal for folks who work with sheet stock on the go–especially when you consider the extra 22” you’ll have to the left of the blade. That’s thanks to the same rack and pinion fence as the smaller Dewalt. It’s even better on a larger scale, where the differences between this design and the sliding rail style you find on Bosch become very apparent. Reviewers agreed that this one felt much sturdier, smoother, and locked more securely than other portable units.
Finally, make sure you know your long-term options when it comes to maintenance, repairs, or replacements. Check the warranty coverage on your portable unit. Read the fine print, checking whether you’ll be paying for repairs under warranty, or whether the company will be footing the bill. Some manufacturers cover repairs, but not return shipping. Others force you to bring your unit to an authorized dealer, which can be difficult in some parts of the country.
What 🤔?? I find it pretty rare to have to re-align the rack and pinion fence on the dewalt, but short of the first time figuring it out, it shouldn’t take more than 5-10 minutes to do. The time savings comes in not having to stick a tape to the fence every time you move it to ensure it’s parallel. I am excited to see other tool manufacturers are using rack and pinion fences now so that there are other options besides the dewalt, namely skil’s latest worm drive ts and the latest hitachi, I’m just not interested in any other fence system on a job site table saw.
If the fence and the miter slot were closer together at the rear of the saw, the dial indicator has a negative reading. If the blade and the miter slot were father apart at the rear of the saw, the dial indicator showed a positive reading. A negative reading meant that the materials being cut might be subject to being pinched and a kick back more likely to occur.
Replacing the hugely popular outgoing W1824, the W1851 is a brand-new Shop Fox hybrid with the same enclosed cabinet as you’ll find on the W1819 alongside features more in line with a contractor’s saw. We chose to review the W1851 as it’s a more flexible option than the W1819 and appeals to a broader range of woodworkers. We rarely review brand new products but in this case we made an exception… With a brand like Shop Fox, it’s not a case of taking a chance but of betting on a winning team.
Disclosure: daringabroad.com blog is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Additionally, daringabroad.com participates in several other affiliate programs, and we sometimes get a commission through purchases made through our links.
Measuring approximately 22” x 38”, the contractor table saw is then next size up from the bench style. It typically sits on an open attached stand or base which may or may not be on wheels. It weighs between 200-300 pounds and is still portable but requires more than one person to lift. This style of table saw is good for woodworking shops, hobbyists, small contractors and DIYers. The 1-2 hp motors have enough power and stability to handle more heavy duty job site work and workshop demands. One of the benefits to these saws is that they still run on standard electrical circuits.
You’ll make most of your miter cuts on a miter saw. But when the material you’re cutting exceeds a miter saw’s cross-cutting capacity, you turn to your table saw miter gauge. These usually aren’t quite as precise, but some manufacturers put more thought and robustness into it than others. If you make a lot of long miter cuts, be sure to pay attention to this accessory.
I never – not even with a big cabinet saw – enjoyed cutting down full sheets, and that isn’t going to change anytime soon. So, for me, the bigger capacity of the big saws isn’t as attractive as just cutting down the sheets with a track saw. Suddenly, with a track saw and a quality saw the size of the 4100, I can achieve the same results in a smaller footprint, for less money, more safely (I consider a track saw safer than manhandling full sheets alone)
While ordering generic no-name products might be fine for something like breakfast cereal, power tools are different. When you use power tools, your safety is at stake. If you pick up some cheapo piece of mass produced junk just because the price is less than a name brand, you might end up paying a lot higher price for it than you counted on. Why? Because generic power tools are not usually held to the quality control and accuracy as big box brands such as DEWALT and Bosch.
Cutting dadoes can be done with a dado stack blade. I use the Freud 208. Blade changes are easy, and there is a lever that locks the blade in place so I can get a good yank on the nut with the included (and stored onboard) wrench. There is an accessory throat insert for the dado blade stack, but the standard throat will easily handle a ¼ thick stack, which is what I usually use.
A gauge will allow you to make very detailed cross and angled cuts. This is a bit of kit that you need to research in great depth as it can make or break the accuracy of your cuts and angles. With a good gauge, you can check blade height, blade angles, miter angles and much more. For further reading checkout Wikipedia’s table saw page and for in-depth air compressor reviews.
The machine has a more conventional rip fence/rail arrangement. The right half of the rail assembly folds out so the saw can achieve its full 30″ of rip capacity — wider than any other model here — but the fence would not slide smoothly over the rails without catching on the hinge joint. While the rip fence did maintain its locked settings, it lacks the heft and build quality of the competition.
More power is also associated with more control. More control also gives you the ability to cut tougher materials. Furthermore, more control allows you to use bigger blades with ease. For instance, a 1500W of the motor will result in swift movement of the blade as it spins. High RPM of the blade gives the user a greater chance of achieving accurate and precise cut. So, when shopping for a table saw, look out for a skill saw with the higher motor rating.
With both saws offering easy bevel and blade height adjustment, the ease of use comparison focuses mainly on the rip fences. Once the Bosch's rip fence is attached to the table, it moves smoothly across the table when unlocked. But unlocking the fence requires a bit of hand muscle. You can adjust the clamping pressure to alleviate this, but make it too loose and the fence may wobble out of square. Modifying the fence locking lever, or using a cheater bar (such as a push stick) works reasonably well.
While you may be tempted to skip straight to the reviews, they are a bit on the technical side and contain plenty of terms you might not be familiar with just yet. My suggestion would be to start by reading the informational articles which will provide you with a decent amount of knowledge on table saws. After that, I sincerely doubt you would be caught off-guard while reading anything in the review section.
The large cutting table surface of the Bosch 4100-09 Worksite Table Saw is roomy enough to handle large work pieces, giving you a ripping capacity of 25”. This is a really great feature if you plan to use the saw to rip solid or plywood panels, or other large materials. I use my table saw primarily for ripping sanded plywood panels for use in cabinetry, and many of my projects would be impossible with a smaller capacity saw. The rip fence glides across the saw cutting table, so you can actually use it with one hand, and locks in place for safety and accuracy. The DEWALT DW745 Job-Site Table Saw offers a 16” cut, considerably smaller than the Bosch. It is perfectly adequate for most application, such as ripping dimensional lumber and small trim applications. The type of materials and work pieces you expect to be cutting are a determining factor in your choice of table saws. If you plan on tackling any large scale projects in the future, the rip capacity of your saw is definitely a feature that you should take into consideration.
As with anything, it’s easy to get overwhelmed with the variety of types, sizes, features, colors, weights, what, when, why, where, who…(let me catch my breath). For now, let’s focus on what’s right for you with our Best Portable Table Saw Guide. We’ll start by identifying quality brands that align with your needs. Besides, who wants to buy something that won’t work?
However, it provides a bit less room to work, and it’s not as easy for newer woodworkers to use. The power/stop switch is rather small, and this one doesn’t have a digital angle display like the Grizzly. We highly recommend it to working professionals who need maximum cutting capacity in a minimal footprint. It’s also a good choice for ambitious DIYers who are short on space, but really know their way around a table saw.
6. Clamp rip fence to check if it holds securely at front and rear. If rear is not clamped securely, un- clamp fence and turn rear clamp adjustment screw 6 clockwise for increased clamping. Try clamping the fence to verify if it self aligns and clamps tightly at the front and rear. Overtightening of the rear clamp adjustment screw 6 will cause the rip fence to be non-self aligning (Fig. 23). Overtightening may cause friction or “chatter” when fence is moved side to side.