If you’re a home DIYer, dust collection shouldn’t be a big worry. You can always hook the saw up to your shop vac, but if you’re only working with it occasionally, you’ll be fine to simply get your sawing done, and clear the exhaust port afterward. However, if you’re working on a professional jobsite, you should plan to collect at least most of the dust from your portable table saw via a vacuum system.

The blade guard is the most noticeable and the most important safety element of every saw. Its purpose is very simple – it keeps your fingers away from the blade. Many people decide to unscrew this part and take it off to speed up the cutting process, but that’s a huge mistake. In fact, a massive percent of injuries happen because people alter the safety mechanisms in order to work faster. Risking your life for a few hours of effective work isn’t worth it, to say the least.


The large cutting table surface of the Bosch 4100-09 Worksite Table Saw is roomy enough to handle large work pieces, giving you a ripping capacity of 25”. This is a really great feature if you plan to use the saw to rip solid or plywood panels, or other large materials. I use my table saw primarily for ripping sanded plywood panels for use in cabinetry, and many of my projects would be impossible with a smaller capacity saw. The rip fence glides across the saw cutting table, so you can actually use it with one hand, and locks in place for safety and accuracy. The DEWALT DW745 Job-Site Table Saw offers a 16” cut, considerably smaller than the Bosch. It is perfectly adequate for most application, such as ripping dimensional lumber and small trim applications. The type of materials and work pieces you expect to be cutting are a determining factor in your choice of table saws. If you plan on tackling any large scale projects in the future, the rip capacity of your saw is definitely a feature that you should take into consideration.
It’s highly portable. Even though the whole body feels sturdier than the Dewalt’s, it’s still relatively light, at just about 60 pounds. There are handles in both the top and bottom edges of the machine, for easy lifting, and once you’ve got the saw fixed to the base, you won’t have to lift it on your own except for when you’re loading it in the back of the truck/van.
We’re not alone in loving the Jet’s guard system. We read lots of reviews from pros who said they’d used lots of table saws in their time, but this was the first time they didn’t absolutely hate the guard. In fact, many wrote that they started working with the guard onboard for the first time, simply because it worked so well. It’s certainly one of the most unobtrusive ones we’ve seen!
Both saws provide great cutting performance, and should handle most homeowner and DIY wood-cutting needs with ease. The saws are marketed as job-site saws, meaning they're designed for construction and home-improvement applications where extreme precision and accuracy is not typically required. This does not mean they're poorly suited for fine woodworking, though. You might not achieve the same precision as with a full-size stationary table saw, but out test cuts were by no means sloppy. And upgrading from the simple miter gauges included with both saws to an after-market miter gauge (such as an Incra model) or a cross-cut sled should improve the accuracy of straight and angled cross-cuts.
I really enjoyed your review and appreciate the significant time and effort put into it. How did you acquire the machines? Were they evaluation units provided by the manufacturers or did you buy them (randomly, like Consumer Reports)? If they were provided to you the cynic in me says you probably got cherry picked units. In looking at the various machines on line and checking out their comments, it’s quite clear pretty much all of them have a manufacturing distribution of performance and metrics e.g. for accuracy all the units you tested have comments ranging from great to truly awful. Same thing for build quality. I spent quite a while looking at the Dewalt but all the negative reviews on quality and accuracy turned me off it. I certainly do see many more positive reviews than negative reviews for the Dewalt, but it does leave you with the feeling that a dice roll is partly involved in buying a recommended table saw.
This woodworking website has tons of information about how to use a table saw: choosing blades, cutting joints, safety features, and more. However, we found only five actual product reviews, none more recent than 2013. Although these individual reviews are hands-on, they don't put saws through any specific, detailed tests. There's also no direct comparison between saws and no formal rating system.
All these saws have fences that extend to at least 24 in. to allow you to rip a 4 x 8-ft. sheet of plywood in half. And they all have a slightly different way of accomplishing this. DeWalt has the most straightforward method. You just push the fence out on its rails and flip over the board support. On the Rockwell saw, you flip out a hinged fence rail. The only drawback to this fence is that it must remain in the extended position for any cut, so it takes up quite a bit of room. The remaining saws require you to release one or two levers and pull out the fence extension.
If you want a table saw that helps you deliver products faster, the Bosch 4100-09 could be what you’ve been waiting for. It has a Gravity-Rise stand that is built for efficient and accurate setup and takes down.The portable construction makes it easy to bring to any worksite with minimal trouble. Only weighing 39 pounds, you will have no problem transporting this table saw wherever you need to go. The Bosch 4100-09 is a powerful saw that is made for the kind of high precision cutting that professionals and DIYers are looking for. It has a 15 AMP, 4 HP motor that generates 3,650 RPMs for clean cuts every time.

Delta has also improved the tabletop geometry on this model which means that you’re going to get more surface area stabilization. The base is also made of durable cast iron and since it offers easy access to the off/on switch, using the Delta UNISAW is a breeze. Other user friendly features include the convenient dust extraction system, large blade opening for easily changing the blade and fine-tuning the riving knife, smart storage for simple organization and fast access.

With a cutting speed of at least 4,500 RPM, nothing will hold you back from getting the job done in minutes. Hitachi job site table saw is designed to give you freedom in your work and the ability to manage your time. Keep every minute accountable by investing in the right tools for your workshop. However, during different occasions, you will have different materials both in size and texture. During such moments, you will require adjusting the fence to accommodate your material and cutting style. This job site table saw is designed with an adjustable feature to ensure your precision and accuracy is not compromised. The low power consumption makes it easy for you to maintain the saw and enjoy smooth and accurate results at no extra cost. When it’s not in use, the table saw has fold and roll stand that guarantees you space saving and convenient storage. The foldable design also makes it easy to transport from one place to the other comfortably.
Table saw flesh sensors are a brilliant and clever piece of engineering. Sawstop revolutionised the industry when they came up with this technology. Human skin is a good conductor of electricity where is wood isn’t. So, the system works by passing an electric current through the table saw blade its self and when it’s cutting wood it’s fine as there is no conductivity between the wood and the blade but as soon as it hits human skin and becomes conductive it triggers an electric brake that stops in the blade in only 0.02 seconds. You may end up with a small cut but at least you won’t lose your finger or worse. There are quite a few different versions now on the market so we would advise you to read plenty of table saw reviews and do you research into the different systems to find the best one for you.
This portable jobsite table saw head-to-head includes 8 saws from; Bosch, Delta, DEWALT, Hitachi, Makita, Ridgid, SawStop and Skilsaw. Originally, we had also to include Ryobi as a budget friendly option for DIY’ers or guys just starting in the trades. However, we were not able to adapt that saw to our testing rigs so we pulled it from the testing (you may see some photos with the saw but again we’re not including it in the results).
We evaluated the flatness of the table by measuring the flatness by placing the edge of a precision ground flat bar across the table and placed feeler gauges in any gaps to measure any difference between the ground bar and the table. TBB took measurements in four directions. As the operator faces the saw, we measured the flatness at the arbor from front-to-rear; we measured the left-to right flatness at the arbor; we measured the flatness from the upper left-to-lower right table corners; and, finally, we measured the upper right-to-lower left flatness between the corners.
×