The design is not bad. The height of this particular table saw is around 35 inches. While some people don’t mind it, we think it could have been designed better. However, the best thing about the design is the fact that you can get both contractor and cabinet style table saws in one unit. Dust control is well-designed. The large 4-inch dust port offers a no-hassle setup, especially with vacuums of lower quality. In simpler words, you don’t need to purchase a super-expensive vacuum for this particular unit; any affordable one should do the job well.


We evaluated the flatness of the table by measuring the flatness by placing the edge of a precision ground flat bar across the table and placed feeler gauges in any gaps to measure any difference between the ground bar and the table. TBB took measurements in four directions. As the operator faces the saw, we measured the flatness at the arbor from front-to-rear; we measured the left-to right flatness at the arbor; we measured the flatness from the upper left-to-lower right table corners; and, finally, we measured the upper right-to-lower left flatness between the corners.
I build guitars in a small shop; I need my saw to be accurate, repairable and easy to store or move. I love this saw! I use it for everything from cutting down stock to slotting my fretboards. It gets out of the way, it came dead on square, and the dust collection works pretty well with a shop vac and great with a high volume dust collector, with an Incra miter fence it makes perfect, repeatable, and accurate cuts. After I had owned it for over a year the plastic lever on the riving knife broke - I called Bosch and they "goodwilled" me a new riving knife assembly (with an upgraded metal lever) via express mail. No charge and fast, friendly service - they didn't even ask for a serial number or proof of purchase. I'd buy this saw again in a minute - all tools wear out or break at some point and I really like that the company stood behind this one and got me up and running again in a hurry. I also love all the safety features - riving knife, anti-kickback pawls, large easy-to-reach power button, nice push stick, and a dust collection port that is positioned out of the user's way.
Finally, hybrid saws combine the lighter weight of the contractor saw with the more powerful motor and sturdier construction of the cabinet saw, at a price that’s easier for the occasional woodworker to stomach. They can run about $1,200 or so, and weigh in at under 300 pounds. Their motors are generally in the 1.5 to 1.75 HP range, and can be used with standard 110V outlets.
However, with proper use, table saws are generally safe tools, advanced blade stopping technology not needed. Therefore considering a saw without such safety features is fine for the cautious DIY user or for the professional carpenter and/or builder. Take into careful account the actual table size of the table saw you are considering. If you are going to be completing rip cuts in large sheets of plywood, then you need a saw with a table large enough to support these big pieces of lumber.
Kenny Koehler An avid endurance athlete, Kenny has competed in triathlons (he's an Ironman) and various other fitness activities. Still, his passions lie with his faith, family, friends, and his love for well-designed power tools. With a background in science, you'll often find Kenny chatting up engineers at media events to get caught up on the latest tool technology.
TBB used an iGauging 35-125-4 digital dial indicator to measure the accuracy of the blade position to the table miter slot. This instrument has an accuracy of .0005 inches. As part of the table saw set-up, TBB installed a new Diablo blade in each saw and these never-before-used blades were used in the measurement test. To ensure that any wobble in the blade did not enter into the test results, TBB marked a single tooth as the reference point for the measurement. The blade position was moved to the front of the saw to allow the iGauging dial indicator to hit the tooth immediately behind the carbide tooth, The iGauging dial indicator was calibrated and the indicator had a reading of zero.

Look for a blade guard and splitter assembly. The guard will keep your fingers and sleeves away from the blade, while the splitter will keep your wood from re-binding together and jamming the blade, or causing kickback. Kickback is one of the biggest hazards of using a table saw, aside from coming in contact with the blade. Make sure you have either a splitter assembly or a riving knife on any cabinet saw you use.

If you are making a cut that will require your hands to get close to the blade, (within 6 inches) use a push stick or two to eliminate the chances of your hand touching the blade. If this is a big concern for you, maybe consider a saw that uses flesh detection to stop the blade. The additional cost of the saw will be instantly appreciated the first time you need it.
While other cabinet table saws may not offer you a clear cut every single time, that’s not the case with the SawStop ICS51230-52. This model features industrial fence system which ensures that every time you cut something, the cut is going to be very accurate and perfectly straight. One last thing to keep in mind is that the unit includes a standard base, while the mobile base and jobsite cart are sold separately.

Both saws accomplish the same thing, but with different results. SawStop’s feature takes about 90 seconds to recover from compared to roughly 1 minute with Bosch. Bosch developed the REAXX to drop the blade without damage while SawStop usually results in a damaged blade that needs to be replaced. The SawStop employs a brake that must be changed after activation at a cost of $69 each. Bosch uses a dual airbag style cartridge. These run $99 each, but you get two shots out of each one.
The JET ProShop Table Saw offers features you The JET ProShop Table Saw offers features you expect from a high-end cabinet saw in the compact design of a contactor-style machine. The transparent blade guard has independent leaves and the quick release riving knife reduces chance of kickback. A low profile riving knife is included for non-through cuts.  More + Product Details Close
The blade guard is the most noticeable and the most important safety element of every saw. Its purpose is very simple – it keeps your fingers away from the blade. Many people decide to unscrew this part and take it off to speed up the cutting process, but that’s a huge mistake. In fact, a massive percent of injuries happen because people alter the safety mechanisms in order to work faster. Risking your life for a few hours of effective work isn’t worth it, to say the least.

6. Clamp rip fence to check if it holds securely at front and rear. If rear is not clamped securely, un- clamp fence and turn rear clamp adjustment screw 6 clockwise for increased clamping. Try clamping the fence to verify if it self aligns and clamps tightly at the front and rear. Overtightening of the rear clamp adjustment screw 6 will cause the rip fence to be non-self aligning (Fig. 23). Overtightening may cause friction or “chatter” when fence is moved side to side.
×