I can’t tell you how many times we’ve pulled out other jobsite saws only to have accessories fall off, or require off-tool storage. Bosch designed the GTS1031, however, to securely hold all of its accessories, even including the arbor wrenches (both of them) and an allen wrench for adjusting the riving knife and dust ejection points among other things. Our favorite was the rip fence, which simply flipped upside down and stored underneath the table – clever! About the most difficult adjustment was the riving knife, which is a tool-less maneuver, but one which requires you to stick your hand way into the blade cavity to reach the release lever. When making any adjustments to the blade, it goes without saying (but we’ll say it anyway) to disconnect power to the saw as a precaution.
The cabinet itself is 19-3/8-inches deep by 19-3/8-inches wide, which makes it the same size as the last SawStop model we looked at on our list of the best products. Included with this cabinet is a 20-inch by 27-inch cast iron table that extends out from the cabinet. This table is durable enough for regular use and will give you more space for working.
If the fence and the miter slot were closer together at the rear of the saw, the dial indicator has a negative reading. If the blade and the miter slot were father apart at the rear of the saw, the dial indicator showed a positive reading. A negative reading meant that the materials being cut might be subject to being pinched and a kick back more likely to occur.
If you’re looking for the perfect cabinet table saw out there, then you should look no further than the SawStop ICS51230-52. This is an industrial grade cabinet saw and is also the highest quality, most powerful and heaviest cabinet saw you can currently get. Its fifty two inch industrial T-glide fence assembly, combined with a 5 HP, 230V single phase motor offers safety, versatility, durability and peace of mind that SawStop is so well known for.
It’s highly portable. Even though the whole body feels sturdier than the Dewalt’s, it’s still relatively light, at just about 60 pounds. There are handles in both the top and bottom edges of the machine, for easy lifting, and once you’ve got the saw fixed to the base, you won’t have to lift it on your own except for when you’re loading it in the back of the truck/van.
Delta has also improved the tabletop geometry on this model which means that you’re going to get more surface area stabilization. The base is also made of durable cast iron and since it offers easy access to the off/on switch, using the Delta UNISAW is a breeze. Other user friendly features include the convenient dust extraction system, large blade opening for easily changing the blade and fine-tuning the riving knife, smart storage for simple organization and fast access.
Even though is seems pretty irrelevant, the position of the On/Off switch is quite important, especially if you’re a frequent user of these tools. In today’s models, the switch is usually leveled with your knees. The main thing you should look for is the size of the OFF switch. It has to be big enough so that you can turn the unit off immediately either with your knees, elbows, or hands. The so-called panic button is one of the crucial elements of every unit, even if it doesn’t seem like it.
Using the guards the saw came with is crucial for the safety of your hands. If you are working with smaller pieces, make or buy a sled with a work clamp so that you can maintain a safe distance from the blade. The clamped sled can be as simple as a piece of plywood with a track on the bottom that’s responsible for riding in the groove. It’s quite simple to construct, saves time, and most importantly – fingers.
Look for a blade guard and splitter assembly. The guard will keep your fingers and sleeves away from the blade, while the splitter will keep your wood from re-binding together and jamming the blade, or causing kickback. Kickback is one of the biggest hazards of using a table saw, aside from coming in contact with the blade. Make sure you have either a splitter assembly or a riving knife on any cabinet saw you use.
With a cutting speed of at least 4,500 RPM, nothing will hold you back from getting the job done in minutes. Hitachi job site table saw is designed to give you freedom in your work and the ability to manage your time. Keep every minute accountable by investing in the right tools for your workshop. However, during different occasions, you will have different materials both in size and texture. During such moments, you will require adjusting the fence to accommodate your material and cutting style. This job site table saw is designed with an adjustable feature to ensure your precision and accuracy is not compromised. The low power consumption makes it easy for you to maintain the saw and enjoy smooth and accurate results at no extra cost. When it’s not in use, the table saw has fold and roll stand that guarantees you space saving and convenient storage. The foldable design also makes it easy to transport from one place to the other comfortably.
If you’re a professional looking for a great table saw for the worksite, you’ll love the features and performance of the DEWALT DWE7480. Equipped with the Site-Pro Modular Guarding System has a rack and pinion telescoping fence rail that will allow you to make fast, smooth and accurate adjustments. This is the perfect table saw for cutting larger shelving and trim easily. With a 15 AMP 4800 rpm motor, you will go through all types of wood, even hardwood, with ease.
The Delta 10 in. Contractor Saw features an The Delta 10 in. Contractor Saw features an industry standard tool-free split guard design that allows a true rise-and fall riving knife by using a lever on the inside the throat plate. It has a tool-less assembly of the riving knife and anti-kickback pawls. There is a large easy to ... More + Product Details Close
Like the last SawStop table saw that we looked at, this one is quite heavy and provides the stability that you need when working with plywood or any other type of wood. You can use the foot pedal on the bottom to operate the saw, but you’ll also find four wheels on the bottom of the cabinet. All four of those wheels swivel in a 360-degree direction to help you move the cabinet to any location.
As accidents and injuries are common when using large power tools like this one, it’s important that you look for safety features such as a dust collection system. Inhaling the sawdust that comes off the wood can make you sick, but this system does a good job of removing the dust from your work area. The collection port itself has a convenient on the cabinet too.
The SKILSAW SPT70WT-01 is truly a woodworking marvel, packing a 15-amp Dual Field motor into a surprisingly lightweight yet durable 49-pound frame. Whether you’re an amateur carpenter or a contractor with years of experience under his toolbelt, SKILSAW’s workhorse of a table saw is an invaluable addition to your repertoire thanks to its raw torque and unparalleled 25" ripping capacity, meaning tearing through thick sheets of plywood has never been easier.
The miter gauges on these saws range from downright flimsy to cabinet-saw quality. All the saws except the Craftsman and the DeWalt also have T-tracks—a nice feature that captures the miter gauge bar, making it easier to start wider crosscuts. Because the Ryobi and DeWalt saws don’t have a standard miter gauge slot, you can’t use accessories that require a 3/4-in. slot.
Hybrid table saws are the latest thing on the market these days. They’re in between contractor and cabinet table saws in terms of price, power, and precision. These have either half-cabinets or cutaway stands like a contractor saw, but with the super-powerful motor and improved stability of a cabinet unit. They’re heavy, so you should be prepared to use them on a wheeled lift, but they can be transported fairly easily if you have helpers.
Consider whether you’ll be working inside or outside, on even flooring or dirt ground. You’ll want to choose the most convenient stand that’s sturdy enough for the kind of cuts you need to make. Pros should pay for a premium stand that doesn’t have any wobble whatsoever. DIYers and framers can probably make do with something lightweight and inexpensive.
Hybrid models vary widely, so there aren’t any strict pros and cons that apply to all models. They’re generally quite powerful, and you can find them in both 110V and 220V configurations. They’re easy to install on wheeled bases, and work well in both stationary or mobile setups. However, these tend to be quite heavy, and they take up more space than other portable options. They’re a good compromise for ardent DIYers who dream of a cabinet model, but don’t quite have the money or the permanent shop space.
Though this table saw will arrive in multiple pieces, Jet includes all the instructions and help that you need to assemble the cabinet and all other parts. The cabinet itself has an enclosed design that keeps the motor and all other components safe from the dust in your workshop and any debris flying around. You also get four legs that attach to the base of the cabinet, which lifts the saw higher in the air to reduce back pain caused by bending over the table.
There are a few nice conveniences which we don’t always see on affordable units like this. The Grizzly has a built-in miter guide, made from cast iron, which slides easily in the worktop. The left-tilting blade is coordinated with a digital display, which gives you an accurate, real-time readout on your bevel angle as you cut! The motor has a starting amperage of 13, which is safer for your breakers than 15 amp models. There’s a standard 4” dust collection port, and
Methods for tilting the blade to cut bevels vary among the saws. The Porter-Cable saw is the only one with a conventional handwheel bevel control mounted on the side of the saw. The crank gives you great control for setting an exact angle. To set the bevel on the Bosch, DeWalt and Rockwell saws, you simply release the bevel-lock lever and tilt the saw to the preferred angle. It’s easy to go quickly from a 90-degree to a 45-degree bevel with this method. The Ridgid, Craftsman and Ryobi saws have a rack-and-pinion setup. These saws utilize the front crank for setting the bevel.
Look for guards with two independent panels on each side of the blade, so that while you work on one side, the other side keeps dust in the vacuum system, rather than flying off to the side. High-end cabinet units also have splitter and guard systems which are molded like the internal shrouding to amplify suction, so you should look carefully at those features.
The DEWALT Table Saw is designed with a The DEWALT Table Saw is designed with a 15 Amp 4800 RPM motor that quickly rips through hardwoods with ease. With 24-1/2 in. of rip capacity this saw easily cuts a variety of larger shelving and trim materials. Rack and pinion telescoping fence rails make fence adjustments fast smooth and ... More + Product Details Close
Hitachi C10RJ 10 in. job site table saw features a powerful, industrial grade 15 A motor that operates at 4,500 RPM, giving you the ripping power to cut through even the toughest woods. This Hitachi table saw has a 0-45 degree bevel and height adjustments. One of the best features is its large work table which also has a telescoping extension, allowing rip cuts up to 35 in. wide! When you pair the power of this table saw with the bevel range and table size, you’ll be able to power through any project you throw at it! Other great features include: front mounted controls, over sized controls, integrated safety switch, and a soft start function that helps decrease recoil at startup.
Lowes had a Father’s day sale, on their Kobalt table saw with a folding/rolling stand and was $180.00, with more money off because I signed up for their credit card-so I bought it. It cuts fine, the fence locks on both ends,measurements seem ok, and it unfolds and rolls away very easily-I like it so far. I’m a home owner and I use it sporadically and treat it well, it does not appear to be very robust, so as a day to day, on the job site saw, probably not a good choice. I used to have a Makita table saw, with a terrible fence, unreliable ruler markings, and difficult to use blade guide that interfered with measurements, which you needed to do every time-a terrible saw, very frustrating to use. I have a Makita miter saw and it’s great, but the idea of buying a same brand because I liked one of their other products did not work out.
The fact is, a table saw is designed to remove a large amount of material in a quick and efficient manner. With the volume of waste that is produced by any but the smallest table saws, a shop vacuum is not going to be up to the task. Short of purchasing a standalone dust collection system, the best that you can hope for from a shop vacuum is that it might keep some of the saw dust out of your eyes.
Make sure you know what’s covered and what’s not, especially if you’ll be using your machine commercially (many warranties are strictly for individual, not commercial use). It’s also a good choice in this case to purchase add-on warranty coverage from a third party at the checkout. We recommend these policies for most portable table saws, since most manufacturers have either very short warranty coverage, or longer warranties which require you to foot the bill for service calls or for returning the machine to the maker.
We rotated the blade to the rear of the saw to enable the dial indicator to contact the same location of the same tooth behind the carbide portion. We positioned the dial indicator to the rear of the saw placed onto the blade and the reading recorded. If the blade and the miter slot were closer together at the rear of the saw, the dial indicator has a negative reading. If the blade and the miter slot were father apart at the rear of the saw, the dial indicator showed a positive reading.
As we said in the beginning of this section, many of these saws will be used, right out of the box, for rough cutting materials and the fine accuracy may not matter so much in that application. If this is the case for a saw, the quality of the cuts and more importantly, the potential safety of the operator is going to be a function of the as-shipped accuracy of the saw from the manufacturer. So, TBB wanted to see how the various saws compared right out of the box. The results are in and, as a group, these eight saws measured up quite well for out-of-the-box accuracy.
After cutting a bunch of wood with this saw, we really liked the balance of power and portability of Bosch GTS1031 – and I think that’s what this saw is all about. For raw Performance, the unflappable motor-blade combo earned a stiff 8/10 in our tests, while its affordable $399 price tag put it at a solid 9/10 in our Value scale. Sure, you can get cheaper portable table saws, but you’ll find it a challenge to track down the combination of power and portability the Bosch GTS1031 offers. Bosch’s gravity rise-equipped 4100-09 remains a compelling alternative or those wanting an integrated stand. It occupies an additional 15″ in width and 8″ in length and is a full 3.5″ taller. But it only tacks on 8 pounds in weight. If you’re cutting larger pieces of wood or need a saw with a stand, the 4100-09 may be your baby, but the new Bosch GTS1031, with its “toss it in the truck” form factor is our new sweetheart tool. While it has an available GTA500 folding table stand accessory, the real advantage of this saw is it’s stand-free portability – so don’t make it into something it’s not. After using this tool, we think you’ll want to take it with you, as-is, just about everywhere!
Both saws provide great cutting performance, and should handle most homeowner and DIY wood-cutting needs with ease. The saws are marketed as job-site saws, meaning they're designed for construction and home-improvement applications where extreme precision and accuracy is not typically required. This does not mean they're poorly suited for fine woodworking, though. You might not achieve the same precision as with a full-size stationary table saw, but out test cuts were by no means sloppy. And upgrading from the simple miter gauges included with both saws to an after-market miter gauge (such as an Incra model) or a cross-cut sled should improve the accuracy of straight and angled cross-cuts.
Kickback (if you didn’t already know) is one of the most common accidents with table saws. In order to prevent this you can make use of the riving knife (you may also find this referred to as a splitter). When the material gets pinched by the blade at a certain angle kickback occurs, but thanks to the riving knife there is no chance of this happening.
When you’re deciding how much to spend, think about how often you use your saw, whether you’re using it as part of a professional workshop or as an avid hobbyist, and whether or not you can expect any return on your investments through your work. We recommend that DIYer spend closer to the $2000 mark, while professionals are more likely to get their money’s worth from something more premium.
The table measures up at 29 inches by 21.5 inches. The 4100-09 is not suitable for dealing with large stock or sheets of wood. Made from aluminum, you’ll meet with no resistance as you slide the timber toward the blade. The only negative with the table is the way it’s finished with an anodized coating. This is fine to start with but tends to wear over time, something that doesn’t just look unsightly but can ultimately affect accuracy. This is a surprising oversight from Bosch and one we hope they rectify in future iterations of this fine table saw.
We’re impressed with how much thought SawStop have put into all the features on this model. It has an extra-large bevel gauge ruler on the side of the cabinet, tool-free, modular guard system, and compatibility with innovative wheelbases which don’t add noticeably to the SawStop’s height or footprint. It also has beveled edges to protect your materials, a very nice touch that our other recommendations don’t have. All in all, it feels like a tool designed by people who use one of these units on a regular basis.
Some table saws go one better than a splitter. Splitters are fixed. They do not move along with the blade. It also needs to be removed if you’re making cross-cuts or dado cuts. A riving knife, on the other hand, is fixed to the same part as the blade. This means it can move along with the blade. Riving knives don’t get in the way either so this is the best option.
It’s highly portable. The Dewalt is available with a folding stand, which makes it extremely easy to pack up. The guard assembly lies flat, and the fence can be retracted all the way to the table to keep everything neat and tidy. It’s pretty light, too-at just 45 pounds. We also love that the adjustment tools, accessories like the miter gauge, and even the guard components can be stored inside the saw for transport, or when they’re not being used.
The fence on a table saw is one of its defining features and allows for precise, square, and repeatable cuts. Not all fences are equal though and a poorly built fence is a deal-breaker, in my opinion. Not only will a poorly built and implemented fence affect the quality of your cuts, but a fence that moves or is not square to the blade can cause your material to bind and kickback.
Safety and precision are usually at a high level. Some models even offer a sliding table as an option to mitigate cross-cutting. Needless to say, hobbyists love the sliding feature because it saves a lot of time and most importantly – nerves. As far as the driving mechanism goes, there are three possible options – single V-belt, serpentine belt, and a multiple V-belts.
TBB measured the accuracy of the factory-set 45 degree stop by using a Wixey WR365 digital inclinometer. This device has an accuracy of 0.1 degree. We placed the Wixey gauge on the table and calibrated the inclinometer to the table by zeroing out the gauge. After that calibration, the measurements shown on the gauge give a result that is relative to the saw table. We attached the gauge to the blade and used the saw mechanism to adjust the blade incline to the point at which the blade or trunnion hit the factory-set 45 degree stop and recorded the measurement. TBB ran the test twice to ensure the repeatability of the measurement. In every case, the result came out to within 0.1 degree of the prior test.
While I appreciate this review, that Kobalt job site saw is the absolute worst. Uncontrollable blade wobble, terrible fence, trundle bolts that are nearly impossible to get to without tacking the back panel off (of course that doesn’t matter when the blade won’t stay in alignment for more than a day), miter slots that aren’t parallel to each other and also taper toward the backside of the table, and a riving knife without adequate adjustments to align it with the blade. Do not buy that piece of garbage.
We absolutely love the guard on this model. Like the Grizzly, the Jet is equipped with a riving knife or splitter, a blade guard, and kickback awls. The Jet’s our favorite of the two to use, because the whole system is modular: you can take it apart or put it back together without using any tools! The splitter (or riving knife) attaches to the same arbor component as the blade, so no matter how you bevel, and no matter what size blade you use, the splitter always lines up without needing any adjustments.
SawStop is the only saw in the group to employ this style fence and they have the best in the group. Ridgid comes in second with a traditional front clamping fence system that has a backside contact point. Its solid construction and wide cast front clamp left us impressed. DeWalt’s came in third with an innovative effort that locks into several points based on where you need it. Rather than sliding along, it stays in place while the rack and pinion system moves it into place. It’s not perfect, but it eliminates a lot of accuracy issues that come from locking the fence out of square on some systems.
Robert Bosch Tool Corporation is aware of questions raised about the power of its REAXX™ Jobsite Table Saw. We are taking this feedback seriously and we’re working with product and engineering teams to answer these questions. Flesh-detecting Bosch Active Response Technology™, which comes on board every REAXX Job Site Table Saw, is unrelated to the questions raised about the saw. The REAXX table saw remains one of the safest and most-advanced table saws available today.
If you’re a home DIYer or pro working mainly from a shop, you may have a wide table or countertop big enough to use the saw without any accessory stand. We would caution against working on sawhorses, though, as they can be wobbly and unsafe. It’s far better to spend a few extra dollars on a sturdy stand than to take risks with a rickety, improvised setup.
One of the most widely used power tools for carpenters is the table saw. For carpenters that don’t work exclusively in the shop a portable jobsite table saw is essential. For this Head-to-Head we’re focusing on corded portable 10″ jobsite table saws. We are not including cordless table saws in this test as we plan on doing another head-to-head exclusively for cordless table saws later this year as several are available now.
Previous buyers said they were at a loss to find materials that the Jet couldn’t cut! They said it went like butter, with no lag whatsoever, and almost no vibration at all. Reviewers raved about the motor’s power, and especially complimented how steadily it ran. This is an excellent choice for hardwoods, thick softwoods, and composite boards: absolutely anything that’ll fit.
Product reviews on this site contain our opinion of a product or service. We will always strive for objectivity and transparency in our reviews. Our goal is to provide readers with honest, objective information based on our own experiences. We never have and never will accept payment in exchange for a positive review. Many of the products that we review are provided to us for free by a manufacturer or retailer. In some cases, we also have advertising or affiliate relationships with manufacturers and retailers of products and services we review. For additional information please visit our additional disclosure policies.
The stand is collapsible and wheeled like others, but it’s not the gravity-rise style. You’ll have to use a foot to stabilize it while you pivot it up or lower it down. The lower locks are released with your feet and there’s some question about the long term durability of the releases. An open housing design has two major results – motor cooling should be more efficient but it trades off storage for an extra blade. There’s really way too much to talk about here, so check out our full review of this model.