Like the Grizzly, the Jet has a standard 4” dust port coming out of the cabinet, and a 220V wiring box for you to attach a power cord. The Jet is also a more shop-friendly tool, since it has much better dust collection. That’s thanks to a fully-shrouded blade and a guard which handily deflects sawdust into the vacuum channel, rather than off to the side of the table.
post-template-default,single,single-post,postid-5816,single-format-standard,mkd-core-1.0.2,ajax_fade,page_not_loaded,,table saw theme-child-ver-1.0.0,onyx-ver-1.4.1,vertical_menu_enabled, vertical_menu_left, vertical_menu_width_290,vertical_menu_background_opacity_over_slider vertical_menu_background_opacity_over_slider_on,smooth_scroll,side_menu_slide_from_right,wpb-js-composer js-comp-ver-4.7.4,vc_responsive
We evaluated the flatness of the table by measuring the flatness by placing the edge of a precision ground flat bar across the table and placed feeler gauges in any gaps to measure any difference between the ground bar and the table. TBB took measurements in four directions. As the operator faces the saw, we measured the flatness at the arbor from front-to-rear; we measured the left-to right flatness at the arbor; we measured the flatness from the upper left-to-lower right table corners; and, finally, we measured the upper right-to-lower left flatness between the corners.
That’s why we’ve created this handy guide! As usual, our trusty team have taken a comprehensive look at all the options out there. We’ve looked for portable units that don’t sacrifice power or accuracy for their small size. You’ll find our Top Three recommendations below, along with a few additional choices for new woodworkers and demanding professionals.

One thing you’ll love about the riving knife is that it allows for adjusting the table saw without using any special tools, for non-through and through cuts including, pictures frames, grooves for shelves, but also cheek cuts for furniture, rabbets and dadoes. There’s also the possibility to store different tools or anything else you may find under the tablet board and given the fact it’s expandable and convenient, it’s going to make using the Delta 36-L552 an even more amazing experience. For dust collection, the table saw comes with a bi-level dust extraction system which offers superior dust collection capabilities.
About three paces from where I tested these portable table saws sits my late-model cabinet saw. As a serious woodworker and magazine editor, I can’t imagine not having it. Its powerful 3hp motor, spacious cast-iron tabletop and almost hair-splitting precision makes most other saw options pale by comparison. But all this said, a cabinet saw isn’t everything. The thought of moving that behemoth down the steps to a basement shop sends chills up my spine. I sure can’t toss it into a car trunk to help a friend down the road. My saw takes up a huge footprint of shop floor, and it cost a small fortune. I don’t know of any stationary table saw that sells for less than $700 new these days, and that can empty the coffer of a modest tool budget.

No matter what you need a table saw for, the three listed above are great choices to consider when you’re doing your shopping around. Whether you’re a professional contractor or a serious DIYer, any one of them will have all the features, power, and portability that you could want in a table saw. All of the ones listed here, and most others have warranties and 30-60 day money back guarantees to give you a chance to see if you like them so your purchase won’t be a waste if you don’t, you will be able to get your money back, but we’re pretty sure that if you choose one of the three that we have detailed for you, you’re going to be able to join the many, many customers who are very happy with their purchases.
To test the saws' cutting prowess, we made a series of cuts on both the Bosch and the DeWalt with woods that homeowners and DIYers might use on a compact table saw. To be specific, we ripped 24" x 24" sheets of 3/4" and x1/4" plywood into strips, and made 45-degree bevel cuts in 13/16"-thick cherry, cross-cuts in 10"-wide, 3/4"-thick shelving, test cuts in 2x4 stock, rip cuts in 3/4" red oak and 30-degree cross-cuts in poplar.
The only dislike that I have found about the Bosch 4100-09’s operation is that unlocking the table causes a tab to pop up above the cutting surface. This tab interferes with the operation of the fence, and could lead to damage of the product. It also comes with only a one year warranty. It does have available rear out-feed extensions available, to help facilitate larger work pieces.
It can seem like plastic is a weight-saver on the part of the manufacturer, but it’s really a cost-saver. You shouldn’t accept shoddy build quality in the name of getting a lighter machine. While no portable unit will include heavy cast iron components like a cabinet table saw, you can find metal alternatives that offer rugged, long-lasting build quality. Instead of plastic, look for aluminum.
Due to the position of the motor, dust collection is often an issue with these units, especially in comparison to the cabinet type. However, an industrial vacuum is usually a small and worthy investment which should solve the issue effectively. The main advantage of this type is the fact that it’s much cheaper than its nearest equivalent – the cabinet type.
If you’re a home DIYer, dust collection shouldn’t be a big worry. You can always hook the saw up to your shop vac, but if you’re only working with it occasionally, you’ll be fine to simply get your sawing done, and clear the exhaust port afterward. However, if you’re working on a professional jobsite, you should plan to collect at least most of the dust from your portable table saw via a vacuum system.
This is a truly great saw, except that it is really tough to adjust the blade and rip fence for parallel. Once adjusted though, it is a fine piece of engineering. What I like best is that the saw is built for the job site. It is extremely beefy, but no too heavy. In my opinion, it strikes a nice balance. Its cart stand is the best in the industry, bar none. Once adjusted, the saw returns to its settings extremely well. It is obviously built for the long haul, and should last a contractor many years. I would definitely purchase this saw again. Now with the things that I wish were better. First, adjusting the blade for parallel is just plain hard. Mine was out from the factory by 4 thousandths. It is a trial and error process, and the instructions suck. Here's what to do: 1. Loosen the four screws indicated in the instructions. Starting from behind the saw, center the blade housing in the rear left to right as best you can, then tighten one screw not quite snug (you want the housing to rotate on this screw when you adjust the front). Next move to the front of the saw and loosen the lock lever for blade angle adjustment (the housing won't move unless you do). Now, begin experimenting with holding the housing at 90 degrees with one hand while sliding the housing back and forth with the other until square. When you think that you are close, lightly tighten one of the front housing screws. Check for parallel (look for videos on how to check a table saw blade for parallel), then tighten the blade angle adjustment lever. With these screws and the lever tight and locked, check again for parallel. If it is still good (I got it to 1/1000 inch of parallel), then lock all the screws and check one more time, if it's still good, then you are done with blade housing adjustment.
If you’re a professional woodworker, you should expect a standard hookup on any saw. However, you’ll find that no portable table saw does a perfect job collecting sawdust. Since these aren’t enclosed tools like a cabinet saw, there are lots of ways for dust to find its way to your floor and spray around your shop. You’ll want to look for the most enclosed, effective design possible, and pair it with a vacuum system that’s got some heft.
As far as the design goes, cabinet saws don’t look much different from the hybrid ones. However, when it comes to sheer power, this type is the most powerful one in every regard. Therefore, devoted professionals who work on massive heavy-duty projects usually prefer cabinet saws over anything else. Each element of a cabinet saw is constructed to withstand a lot of stress and pressure.
Safety is at a pretty high level, to say the least. There are a few integrated mechanisms that prevent accidents from happening, but that doesn’t mean you shouldn’t handle it with care. Also, don’t forget to wear safety equipment at all times. Whether you’re a professional or a beginner, you’ll definitely like this particular model due to its versatility and a wide array of potential.
Bigger tables offer more potential for additional extensions. For example, if you’re planning to process a massive piece of wood but you cannot cut it in smaller pieces; a table extension will definitely come in handy. There are a lot of commercial add-ons you can choose from, but you can also construct one yourself if you’re experienced enough. Experimenting with these things never gets old or boring, but keep safety in mind at all times. Make sure it’s completely safe to use the said extension and pay special attention to the amount of vibrations and the overall integrity of the table after you’ve installed the add-on.
Table saws in this best table saw review run the gamut in price and quality. You can buy a table saw for as little as $150, and if you use it just to occasionally rip a board, that may be all the saw you need. If you want a saw that’s easy to carry and you don’t need to rip sheets of plywood in half, look for a “compact” saw like the DeWalt DW745 (shown) or the Bosch GTS1031. If you have room for a little larger saw that’s slightly less portable but capable of wide rips, consider one of the best table saws we review here. And finally, if you want to build cabinets or furniture and have a big enough work area, you can step up to a stationary contractor’s saw like the Ridgid R4512 (shown), for about $650.
Even though the trunnion mechanism from Powermatic has been known to be the best there is, further refinements have been made to it in order to make it even better. The conically shaped worm gear drive with better surface area, the high end bearings, but also the cast iron, box style construction combine with the solid and smooth feel of the height and tilt adjustments. Thanks to the adjustable backlash, it’s very easy for users to adjust the mechanism back to the factory fresh feel and clearances.
If you’re a home DIYer or pro working mainly from a shop, you may have a wide table or countertop big enough to use the saw without any accessory stand. We would caution against working on sawhorses, though, as they can be wobbly and unsafe. It’s far better to spend a few extra dollars on a sturdy stand than to take risks with a rickety, improvised setup.
One important aspect to consider when buying a new table saw or looking for a new blade is axis adjustment. Being able to adjust the vertical height of the blade allows you to control the depth of the cut, it’s also useful when you don’t need to cut all the way through the wood, especially useful with thick pieces of wood. To help making bevel cuts and joints you can adjust the blade to certain angles that you require.
The blade is a 24 tooth carbide tipped blade that is durable and long lasting. You can even adjust it to a 45 degree angle for those more difficult bevel cuts. If you’re working on uneven ground, you’ll love the rear feet that are fully adjustable so you can level you work space. You’ll get a lot of use out of the onboard storage that will give you easy access to the push stick and guarding components. Weighing only 45 pounds, you can move the table saw from work site to home with ease.
If you’re going to be transporting your unit regularly, you should aim to keep weight to a minimum. Look for something lightweight, with convenient carrying handles, or a stand that can be wheeled around dolly-style at the worksite. Conversely, if you’re only going to be using your portable saw occasionally, you can probably stand a bit more weight.
Other features include a battery-powered laser for lining up cuts. I found it to be pretty dim under bright shop lights and not lined up correctly with the blade. It is non-adjustable. A pullout rear extension provides some added support for long rip cuts. Rockwell also offers a couple of unique accessories: a sliding miter table ($179.99) and a power planer-style “Finisher” ($129.99). It mounts on the saw for flattening board edges.

You will not always get your job within the workshop, there are moments where you will have to get out and work from a distant place. Therefore, you will require having a table saw that is portable and reliable for such duties. Rockwell table saw with a laser has large legs with wheels. You can easily pull it to any place comfortable as the wheels keep rolling. In other words, you will not have to struggle with the entire unit trying to lift it when you want to switch working positions. Additionally, this table saw has a foldable fence for convenient storage and also ensures there is enough room for all size material. The inclusive laser guide is to ensure you get consistency in accuracy. Once the blade is not in the position, the laser guide adjusts automatically for the benefit of the user.
×