Buying a table saw can cover a lot of bases. You have everything from DIY models to professional production level cabinet table saws. In this article, we’re looking what is arguably the most popular – jobsite table saws. They’re on the less expensive side and are highly portable compared to their shop counterparts. That makes them go-to tools for framers, jobsite carpenters, and Prosumers.
If you want to have a quick and accurate cut of wood, look no further than a table saw. When buying a table saw the main thing you put into consideration is its power. A good table saw should have enough power to cut through wet timber as well as hardwood. However, there are certain features which help in foreseeing the overall performance of a table saw.
Carrying things standing on end is easier, since it makes for a narrower package that can easily fit by your side. You’ll be able to lift a heavier saw less awkwardly in that position than if you were to carry it out in front of you. You’ll also want to think about size in terms of where you need to fit the saw in the vehicle, and where you’ll be storing it when it’s not in use.

Both saws were almost equally quick to setup for use, with the DeWalt coming out slightly ahead. The throat plate, which is thicker and sturdier than Bosch's, is slightly easier to remove and reinsert. The DeWalt's blade cavity offers greater clearance, which makes locking down and loosening the riving knife easier without scraping a knuckle. Dewalt's riving knife adjustment required less wiggling and hunting to get it set properly.


How big a table saw is, is determined by the largest blade the saw will hold. 8” blades are the smallest that should be used for any home workshop. You can get blades in 9”, 10”, and 12” sizes as well. Most workshops will not really need the 12” blade as this has a very deep cut capability, but for construction firms and larger, commercial shops, the 12” comes in handy.


After spending hours doing a lot of research and talking to professionals who use these tools on a regular basis we have put together a review for you that not only tells you three of the top table saws on the market today, but we tell you why they are popular and explain a bit about each so you have a good idea of what they are like. This table saw review will put much-needed information right at your fingertips so you can make a good decision on the right table saw for your needs.
The miter gauge gets an “its fine” grade. Ok to support a narrow piece for a crosscut, but not long enough to do much more than that. I upgraded to an Incra miter 1000SE and never looked back. Although a crosscut sled is pretty easy to make (and I highly recommend getting one) I picked up an Incra Miter Express sled for real cheap at a garage sale, so I am happy to use that.
Some previous buyers had motor trouble. Their units conked out early, or worked inconsistently. Apparently, that was down to cheap internal bearings used in the first few iterations of the Bosch. However, according to company replies to some reviewers who cited the issue, the problem has been addressed in the last few versions of this model. We’ve also found that reviews from the past few years are much more consistently positive.
For this portion of the testing and evaluation we used three different materials (3/4″ AC Plywood, 5/4 Mahogany Decking, and 5/4 Pressure Treated Southern Yellow Pine Decking) while measuring the saw blade RPM, and the saw motor AMP draw. To compare the saws we’re looking for how much blade speed each saw has under load, and also how much the amp draw increases under load. Think about it like driving a car, a more powerful car will not drop as much speed going up a hill and the engine won’t work as hard.
The price is acceptable. One cannot say it’s a cheap piece of equipment because it’s not. But, the high quality of production and a great deal of precision justify the somewhat premium price. If you’re a devoted professional, the price shouldn’t be much of an issue for you. The only downside many people reported is the quality control within the company. Many models came with broken or missing parts.
From the triple belt drive system, to the three-HP motor and the large cast iron table and wings, the Shop Fox W18193 s built like a tank. You’re also going to love the T-slot miter gauge that features a fence extension and flip stop, but also a four inch port for dust collection and camlock T-fence. There’s also a twenty nine and a half inch rip capacity.
TBB measured the accuracy of the factory-set 45 degree stop by using a Wixey WR365 digital inclinometer. This device has an accuracy of 0.1 degree. We placed the Wixey gauge on the table and calibrated the inclinometer to the table by zeroing out the gauge. After that calibration, the measurements shown on the gauge give a result that is relative to the saw table. We attached the gauge to the blade and used the saw mechanism to adjust the blade incline to the point at which the blade or trunnion hit the factory-set 45 degree stop and recorded the measurement. TBB ran the test twice to ensure the repeatability of the measurement. In every case, the result came out to within 0.1 degree of the prior test.
Compared to some of the other miter saws we’ve used – predating the new riving knife requirement, the Bosch GTS1031 guard system is much easier to install and remove when necessary (and to put the saw back into portable mode). We timed ourselves and assembled and tore down the saw in just over 2 minutes – and we were confident that our time would get better with more practice. The table is made of machined cast aluminum and is texture-coated to make it fairly slick – something that really helped when cutting larger pieces of 3/4″ plywood for a workbench surface. As for extending the table – that was super-easy. You just lift the table extension handle upwards and slide the table to the right. This gives you a full 18″ of rip width to the rip fence with your material to the right of the blade. Collapsed, you get up to 10″. Motion of the rip fence and the table extension were smooth. While the fence had some wobble in it at the far end – this completely disappeared when you locked it down – and the shape of the rear of the fence locked it straight every time. It’s a good system and more than adequate for a low-cost portable saw like this. We’ve seen more robust fence systems. But typically the trade-off has been in weight as well as cost.
I never – not even with a big cabinet saw – enjoyed cutting down full sheets, and that isn’t going to change anytime soon. So, for me, the bigger capacity of the big saws isn’t as attractive as just cutting down the sheets with a track saw. Suddenly, with a track saw and a quality saw the size of the 4100, I can achieve the same results in a smaller footprint, for less money, more safely (I consider a track saw safer than manhandling full sheets alone)
TBB used an iGauging 35-125-4 digital dial indicator to measure the accuracy of the blade position to the table miter slot. This instrument has an accuracy of .0005 inches. As part of the table saw set-up, TBB installed a new Diablo blade in each saw and these never-before-used blades were used in the measurement test. To ensure that any wobble in the blade did not enter into the test results, TBB marked a single tooth as the reference point for the measurement. The blade position was moved to the front of the saw to allow the iGauging dial indicator to hit the tooth immediately behind the carbide tooth, The iGauging dial indicator was calibrated and the indicator had a reading of zero.
Replacing the hugely popular outgoing W1824, the W1851 is a brand-new Shop Fox hybrid with the same enclosed cabinet as you’ll find on the W1819 alongside features more in line with a contractor’s saw. We chose to review the W1851 as it’s a more flexible option than the W1819 and appeals to a broader range of woodworkers. We rarely review brand new products but in this case we made an exception… With a brand like Shop Fox, it’s not a case of taking a chance but of betting on a winning team.

The first thing you should do before starting up your unit is to check whether you’re wearing all the necessary safety equipment. Gloves are something not many people like to wear. Apart from keeping your fingers safe, they also offer protection against thorns. As you may assume, you’ll work with a lot of thorns flying around. However, gloves aren’t mandatory, and they won’t offer much protection apart from occasional thorns.
As you can tell, this particular type is in the middle between portable and contractor. Some people can finish their projects with bench top saws, but the ones who can’t usually opt for hybrid saws because they are cheaper than contractor ones. One cannot say they are cheap per se, but it’s a significantly smaller investment in comparison to contractor models.
The DCS7485T1 60-Volt MAX 8-1/4 in. table saw The DCS7485T1 60-Volt MAX 8-1/4 in. table saw is maximized for accuracy capacity and runtime. The brushless motor delivers the power to cut all common materials the rack and pinion fence allows for fast easy adjustments and provides the capacity to rip 4x8 sheet goods. The DCS7485T1 comes with 1 ...  More + Product Details Close
How do you tell what the best table saw is? With so many table saw choices on the market it’s hard to know which table saw is the best fit for you and your woodworking needs. Not for long. We’ve taken the leg work out by doing all the measuring, tracking, and researching for you. We’ve compiled year-over-year performance and pricing information for over 3 years to help you choose the table saw that is ideal for you and your project. Search no more, find your table saw below.
While DeWALT’s DW744X is the only model here without wheels, the saw is otherwise well appointed. It’s got a unique rip fence design: instead of sliding along front and back rails, the fence is fixed to them. To change rip fence settings, you extend the rails out on rack-and-pinion gears. The design keeps the fence parallel to the blade/miter slots and prevents it from deflecting if pushed laterally. A red hairline cursor makes fence settings easy to read, and it passed my ripping tests with flying colors.
Buying a table saw is one of the biggest and most important purchases you will ever make when it comes to power tools. It is an integral part of most job site equipment, as well as an essential item for most do it yourself projects. Choosing a table saw that fits your particular needs and budget can mean the difference in both profitability and frustration level.
Overall, the Dewalt's combination blade leaves a slightly smoother finish, but both brands' general purpose construction blades are good enough to start off with. Cross and rip-cut edges were fairly smooth, but users who plan to cut down a lot of plywood will definitely want to invest in a more suitable saw blade. Both saws provided ample cutting power without a noticeable difference in cutting speeds, so we're calling this one a tie.
But, their price point reflects that. If you want the absolute best table saw money can buy then you can go pay $10,000 and it’s yours. We always accept a certain number of tradeoffs depending on what our budget allows So, if I am only doing a few DIY projects a year, I am not a carpenter by trade, and my budget is limited, the SKIL table saw may be right up my alley.
While ordering generic no-name products might be fine for something like breakfast cereal, power tools are different. When you use power tools, your safety is at stake. If you pick up some cheapo piece of mass produced junk just because the price is less than a name brand, you might end up paying a lot higher price for it than you counted on. Why? Because generic power tools are not usually held to the quality control and accuracy as big box brands such as DEWALT and Bosch.
One of the principal causes of table saw accidents is kickback. This process happens when a piece of wood is ejected at great speed in the direction of the user. Binding between the blade and fence, the wood then gets trapped in the teeth and spat out. A splitter is a vertical blade that holds the kerf open to minimize the chance of kickback. 2 pawls are attached for this purpose.
If you’re going to use your table saw every day, make sure you spend a bit more money for something of the heaviest build quality, with extended warranty coverage from a company with a great reputation for service. If you’re going to be using your cabinet unit only periodically, you probably don’t need to buy something premium. You’ll be able to get by with something around the $2,000, since you won’t be spending enough time cutting to really appreciate the design touches and tweaks that make the more expensive units more of a pleasure to use.
These table saws are all probably made in China where there’s apparently no meaningful out-going quality control. While the *average* quality from a given manufacturer might be great, you could also be unlucky get a piece of junk because *everything* made on the production line ships out. It’s a preferred business model these days – the prices are much cheaper but the manufacturers trade that off against dealing with significantly increased returns and the need for much more customer service.
It has a machined aluminum table which is extremely precise. We like the Dewalt’s cast metal table for the price, but the company don’t list the material, and we suspect it’s not nearly as rugged as aluminum. The Bosch’s table is much better. It’s rugged, sturdy, and more consistently even than the Dewalt. The table makes this one a smarter choice for fine woodworkers or pros who need superior alignment.
Bosch GTS1031 10 in. portable jobsite table saw is powered by a 15 Amp motor that allows this table saw to rip through any lumber or hardwood quickly and easily. Bosch’s Smart Guard System provides added control while cutting, SquareLock Rip fence ensure consistent and accurate cuts, and an all steel base provides added durability. Oh yeah, and we forgot to mention the price. This is the most affordable table saw on our list!
Electric brakes in the saw is an important feature as helps the saw in reversing electricity in the motor, thus contributing to a precise cut. It is highly recommended that when you are buying a saw choose the one with on and off switch. The switch should be easily accessible to make work better and more efficient. In addition, the switch should have a cover. This will keep you from accidentally turning the saw on and damaging your work area or cutting yourself.

Like the Bosch, this Dewalt comes with a rolling stand. It’s convenient to set up and take down, since you can do it without helpers or tools. It rolls like a dolly, and opens into a nice, sturdy table. We especially like the splayed legs, since they lend the whole thing a bit more stability than the Bosch version. Unlike the Bosch’s stand, the Dewalt’s has semi-pneumatic tires which won’t ever go flat.
The machine has a more conventional rip fence/rail arrangement. The right half of the rail assembly folds out so the saw can achieve its full 30″ of rip capacity — wider than any other model here — but the fence would not slide smoothly over the rails without catching on the hinge joint. While the rip fence did maintain its locked settings, it lacks the heft and build quality of the competition.
×