The most critical safety feature on a table saw is the blade guard. It’s all that separates your fingers from the rapidly rotating blade. You need this to be transparent or it will make measuring awkward. The last thing you want is to be tempted to remove an unfit guard. Check closely for a clear, flexible blade guard. Safety is paramount when operating a table saw.
It’s built heavy. Like our other recommendations, this one has a machined cast iron worktop, and all-steel cabinet. There are miter slots cut into the worktop, and the bevel and height adjustments are via machined metal flywheels that are calibrated and balanced with the trunnion. We especially love the internal gearwork for raising the motor, which has precise torque bolts and a gas assist to make all your adjustments both smooth and easy. The cabinet is powdered steel for added durability, and the Professional woodworkers and amateur reviewers alike said they were above impressed with the overall build quality. This one feels as premium to use as you’d expect from the pricetag.
TBB measured the accuracy of the factory-set 45 degree stop by using a Wixey WR365 digital inclinometer. This device has an accuracy of 0.1 degree. We placed the Wixey gauge on the table and calibrated the inclinometer to the table by zeroing out the gauge. After that calibration, the measurements shown on the gauge give a result that is relative to the saw table. We attached the gauge to the blade and used the saw mechanism to adjust the blade incline to the point at which the blade or trunnion hit the factory-set 45 degree stop and recorded the measurement. TBB ran the test twice to ensure the repeatability of the measurement. In every case, the result came out to within 0.1 degree of the prior test.
The whole thing is a bit more versatile than the Dewalt, thanks to expanded fence rails and an extended trunnion set. It has a wider rip capacity than the Dewalt. This one uses a traditional sliding-rail fence which gives you a rip capacity up to 25 inches. The fence locks at either side, like the Dewalt’s. It also has a wider bevel range, tilting up to 47 degrees.
If you want to take the saw with you and use it in a different location, you can purchase the optional MB-PCS-000 integrated mobile base which features 2 stationary casters and 2 pivoting casters. Furthermore, it’s also possible to upgrade the mobile base assembly to a one thousand pound lift capacity, add a hydraulic piston lift and 4 independent pivoting casters.

Because we’re passionate woodworkers who care deeply about the quality of the tools we work with, we have a tendency to recommend that even the most budget-conscious buyer spend a little more to get something high-quality. However, we know that some DIYers might have the ambition to take their woodworking to the next level with a table saw, but might not necessarily have the funds.
Consider whether you’ll be working inside or outside, on even flooring or dirt ground. You’ll want to choose the most convenient stand that’s sturdy enough for the kind of cuts you need to make. Pros should pay for a premium stand that doesn’t have any wobble whatsoever. DIYers and framers can probably make do with something lightweight and inexpensive.
I knew there were jobsite table saws on the market for less than $250, but I never thought they were good enough to get my recommendation. Sure, the SKIL 3410-02 is not a professional saw and may not be versatile enough for contractors, but the stand, power, accuracy and build quality of this table saw are much better than I thought possible in this class.
The Delta 10 in. Contractor Saw features an The Delta 10 in. Contractor Saw features an industry standard tool-free split guard design that allows a true rise-and fall riving knife by using a lever on the inside the throat plate. There is tool-less assembly of the riving knife and anti-kickback pawls. It has a large easy to access ...  More + Product Details Close
If you are making a cut that will require your hands to get close to the blade, (within 6 inches) use a push stick or two to eliminate the chances of your hand touching the blade. If this is a big concern for you, maybe consider a saw that uses flesh detection to stop the blade. The additional cost of the saw will be instantly appreciated the first time you need it.
Skilsaw SPT70WT-22 is a portable 10 in. Worm Drive table saw designed for ripping and is the first of its kind to hit the market. This Skilsaw has a powerful Dual-Field 15 amp motor that is powerful enough to handle even the toughest jobs. The motor has a smooth startup and runs cooler, so it lasts longer. With a small, compact size, easy to transport size, this portable saw has a lot to bring to the table. Skilsaw’s SPT99-12 is also this same table saw but also includes a rolling stand which allows you to easily transport and move this saw around the job site.
Hybrid models vary widely, so there aren’t any strict pros and cons that apply to all models. They’re generally quite powerful, and you can find them in both 110V and 220V configurations. They’re easy to install on wheeled bases, and work well in both stationary or mobile setups. However, these tend to be quite heavy, and they take up more space than other portable options. They’re a good compromise for ardent DIYers who dream of a cabinet model, but don’t quite have the money or the permanent shop space.
The rip fence has a nifty flipping action so you can hold 2 different positions. This is an awesome feature if you’re cutting especially narrow workpieces. One of the dangers of ripping substantial pieces of lumber is breakage or the saw itself toppling over. The rail extension gives wonderful stability and allows you the freedom to undertake ambitious projects in complete safety.
A lot of the modern table saws nowadays will have a dust collection port where you can hook up a vacuum or extraction system to it. We would always recommend that you purchase a table saw with a dust port, always check the size of the port to make sure it fits with either your vacuum or your extraction system, or you can always modify something to make them fit.
You should test the cutting depth of a saw when it is not cutting a bevel. This aspect helps in determining accurate and maximum cutting at 0 degrees. In considering bevel cutting, you should ensure the base plate is adjustable. Look out for adjustment allowance that your saw offers you such as 45, 50 or 90 degrees. The table saw should also be a feature with the flush housing so as to allow the table saw to cut very close to the edge of the wall. It is necessary to look out for this feature as will allow you to cut flooring to size at ease
Perfect for both hobbyists and craftsmen, the PCS31230-TGP252 from SawStop is a 3 HP cabinet saw that delivers excellent performance while featuring the company’s patented safety system to ensure maximum safety during use. The safety system is similar to that of the G0690 from Grizzly where the blade stops in milliseconds after it comes in contact with flesh. Designed and built in order to satisfy the needs of the most demanding users, the PCS31230-TGP252 features an exacting finish and feet and a superior dust collection system. For increased precision and added strength, the PCS31230-TGP252 features a fifty two inch T-Glide fence system, but also an extension table and rails.
Product reviews on this site contain our opinion of a product or service. We will always strive for objectivity and transparency in our reviews. Our goal is to provide readers with honest, objective information based on our own experiences. We never have and never will accept payment in exchange for a positive review. Many of the products that we review are provided to us for free by a manufacturer or retailer. In some cases, we also have advertising or affiliate relationships with manufacturers and retailers of products and services we review. For additional information please visit our additional disclosure policies.
From dust collection and onboard storage through to on/off switches and table extensions, most reputable table saws come equipped with everything you’ll need to rip up the wood of your choice. Whether it’s making your life easier with wheels enabling height and tilt adjustment or a safety feature like the magnetic switch, the functionality of table saws is impressive. You can upgrade the blades, get various jigs or dado blades and generally enhance the way your saw performs.
In addition, a top-quality fence should move smoothly and have a scale that’s accurate and easy to read. Our favorite is the DeWalt fence. The rack-and-pinion system keeps the fence parallel to the blade, and the micro-adjusting knob allows easy and precise fence positioning. Runners-up in this category for best table saw are the Ridgid and Bosch saws. They both have superb fences, with the added advantage of T-slots for attaching accessories like featherboards.
When the blade touches flesh, a brake will stop the blade and the blade drops down below the surface of the table. The operator will presumably leave with only a small nick or no injury at all. These systems definitely bump up the price of the saw, but it’s a major safety feature and just might be able to save you some very expensive medical bills, along with your fingers.
It’s expensive. This one will cost you over $3000. That’s no casual purchase, and the high price tag makes this cost-prohibitive for some buyers. However, you really can’t put a price on the peace of mind that comes with having a unit with this sort of safety system onboard. Our advice? If you can muster the cash, and will get your money’s worth out of the machine, it’s well-worth the price.
RIDGID’s 94-lb. R4510 might not be a saw you want to lift into a truck bed every day, but it’s bound to deliver solid cutting results once you reach your destination. For starters, this saw includes a downright great stand. Step on one lever, and the tubular frame lifts and glides smoothly up into place. The same lever collapses it. It’s sturdy, well-balanced and provides a wide stance to keep the saw from shifting or tipping. Large wheels and rubber tires roll the machine around easily during transport or just to reposition it when set up. The left-most tube is both a working-height handle and side support for balancing extra-long crosscuts. Smart.

The scales that indicate the width of cut fall into one of two categories: continuous and separate. Of the seven we’re reviewing, DeWalt, Ridgid and Rockwell are continuous. You simply line up the fence with the desired measurement. The other four best table saw options—Bosch, Craftsman, Ryobi and Porter-Cable—require you to lock the fence in a specific position on fully extended rails, and read the dimension on a separate scale. We prefer the continuous scales and really like the tape measure–type scale on the Ridgid.


I appreciate the helpful comparison of the best table saws. I’m fairly new to woodworking, and until recently I was using an old table saw that used to belong to my dad. Long story short, it’s no longer usable, and so I’m looking for a good table saw to buy that’s beginner-friendly. I have my eye on the DEWALT DW745 – evidently it’s really popular and does a great job. I’ve taken a look at some other sites for more ideas. Your guide here is great. What is your opinion on the DW745?
Hitachi C10RJ 10 in. job site table saw features a powerful, industrial grade 15 A motor that operates at 4,500 RPM, giving you the ripping power to cut through even the toughest woods. This Hitachi table saw has a 0-45 degree bevel and height adjustments. One of the best features is its large work table which also has a telescoping extension, allowing rip cuts up to 35 in. wide! When you pair the power of this table saw with the bevel range and table size, you’ll be able to power through any project you throw at it! Other great features include: front mounted controls, over sized controls, integrated safety switch, and a soft start function that helps decrease recoil at startup.
We hear the term accuracy tossed around when it comes to finding the best portable jobsite table saw, but we really have to narrow down what that means. Every saw we tested has the capability of being calibrated and it should be the first thing you do after setting it up. Like a new miter saw, blade calibration is simply part of delivering professional results.

To make our recommendations for the best table saws, and the best table saw bargains, we consulted comparison tests and single-product reviews in tool-related publications such as Pro Tool Reviews, Woodworker's Journal, Popular Mechanics, Tools of the Trade, and Fine Homebuilding. Many of these reports are several years old, but most of the models tested are still available. Most professional reviews focus on portable table saws, but we found a few that cover contractor and cabinet saws.


Paul – Good catch….I’ve updated that to say Skilsaw not SawStop…thank you! As you can imagine…all the data makes it tough to keep it all straight. I’m not even sure how you’d install that aftermarket fence on these saws. If you do I’d love to see how!! Those really look like they are made to install on cast-iron full size saws. I’d choose the DEWALT with a slight edge over the SKilsaw.
On the downside, Delta have changed things up over the past few years, and the news isn’t all good. The motor is still made in the USA, but the frame and structure of the saw is all imported. Recent buyers have reported shoddy quality control and very poor customer service since the company was taken over. Even though the Unisaw still gets great professional reviews, buyers’ experiences are so mixed that we’re not comfortable recommending this one as one of our top picks.
Ryobi’s RTS21G comes in as the only table saw in the group under $200. It’s lightweight, reasonably compact, and we got acceptable jobsite cuts with the upgraded Diablo blade. The throat plate uses magnets to hold it in place while leaving it easy to remove for blade access. Using a threaded rod to push the height adjustment up, you’ll notice it’s easier and smoother on the way down. The stand folds up and can be Velcro-strapped to the back, though it’s a bit wobbly compared to the others when ready for action.
To get the feel of the cut, we used a two man team to feed from one end of the saw and catch on the other. This helped us reduce the friction that comes from one person trying to hold a board flush against the fence while also keeping downward pressure to keep it level on the table. There was definitely some hesitation at the beginning of each cut that was alleviated once the board was received by the second man on the other side. It was during this middle section that the table/fence friction was at its lowest point and we made our determinations about each saw’s power and cutting speed.
Porter-Cable comes in as the most expensive of the value group, but also with the best overall performance in it. Of the three saws in this class, it had the best cutting power and also came in the top spot overall for height and bevel adjustment thanks to independent wheels. This may seem like a small consideration, but when you actually need to cut accurately beveled pieces, the adjustment wheel is a huge benefit over sliding the front height adjustment around.
According to the many reviews posted online, the JET 708675PK is an excellent table saw that features a finely ground and large cast iron table that measures twenty nine by forty two inches and provides plenty of work surface for even the most demanding projects. Also, taking a closer look at the front of the blade, you’ll notice it includes ten inches of clear table which is certainly going to be appreciated by a lot of users. Looking under the table, you’ll notice a wide stance, heavy duty cast iron trunnion mechanism which provides the remarkable performance, almost vibration free operation and incredible stability the JET 708675PK is known for.
The professional level saws saw a separation as well and all were well ahead of the cutting power we saw with the value group. A middle tier of cutting performance started with Makita and Bosch’s 4100 while DeWalt was significantly better. Entering the fray with the only worm drive system, we had high hopes for Skilsaw’s entry. It was solid and smooth—definitely at the Pro level— and close to what the 4100 delivered.
Plus, the machined aluminum table is our favorite on the market right now. It also has a smarter motor system than either of the Dewalt’s, thanks to a soft start and automatic speed control to ensure smooth cuts. However, it’s the slowest of the pack, and it doesn’t have quite as good a fence as the yellow competition. We think it’s a great choice for pros who are concerned about accuracy, but can’t spend lots of money on their unit.
Measuring approximately 22” x 38”, the contractor table saw is then next size up from the bench style. It typically sits on an open attached stand or base which may or may not be on wheels. It weighs between 200-300 pounds and is still portable but requires more than one person to lift. This style of table saw is good for woodworking shops, hobbyists, small contractors and DIYers. The 1-2 hp motors have enough power and stability to handle more heavy duty job site work and workshop demands. One of the benefits to these saws is that they still run on standard electrical circuits.
It’s the safest of the three by a long, long shot. SawStop became a major brand thanks to a feature that they’ve named their brand after: an accident-proof stopping mechanism for the traditional table saw. The innovative brake system on this model is the best on the market at detecting flesh and stopping the blade immediately. It’s a sure bet for saving fingers or worse injuries in the workshop.
Below is a graph showing the average measured decibels for the saws (for each of the materials we tested). As you can see the saws range from 93.7 db to 97.9 db. OSHA allows 8 hours of exposure for up to 90 db, from 95 db up the exposure limits start dropping quickly starting at 4 hrs for 95 db so clearly these saws all need hearing protection. We ranked the quietest 3 saws as a 2, and the remaining saws as a 3 and felt none should rank a 1 due to the need for hearing protection.

Goggles are yet another thing people simply don’t like wearing. However, it’s not about comfort but saving your eyesight. As you can assume, there is a lot of sawdust flying around while you’re cutting a piece of wood. In order to prevent it from flying straight into your eyes, you have to wear safety glasses. There are hundreds of models you can choose from, but make sure they are certified as safe. In simpler words, you cannot use the first ones you stumble upon, don’t be afraid to invest in high-quality safety glasses, you’ll be thankful for them.
When the blade touches flesh, a brake will stop the blade and the blade drops down below the surface of the table. The operator will presumably leave with only a small nick or no injury at all. These systems definitely bump up the price of the saw, but it’s a major safety feature and just might be able to save you some very expensive medical bills, along with your fingers.
Look for a blade guard and splitter assembly. The guard will keep your fingers and sleeves away from the blade, while the splitter will keep your wood from re-binding together and jamming the blade, or causing kickback. Kickback is one of the biggest hazards of using a table saw, aside from coming in contact with the blade. Make sure you have either a splitter assembly or a riving knife on any cabinet saw you use.
More expensive models also have more efficient drivetrains, which means they achieve a higher cutting speed for smoother, faster, and trouble-free cuts. Plus, their innovative belt designs and calibrated trunnion supports make the whole cutting experience smoother, quieter, and simpler. You’ll also pay extra for innovative safety features like skin detection, paddle power switches, magnetic switches, and thermal overload protection.
×