Install new blade- With the new blade, face the teeth of so they are pointing to the front of the saw table. Place the blade on the housing. Secure the new blade with the washer and nut with the use of a wrench. Make sure you are turning the wrench in a clockwise motion. Use the small piece of wood to secure the blade in place while you are securing it.

But with top quality saws come features that some people may find well worth the extra investment, substantial though it may be, and thus our discussion starts with pricier models. At the top price range for table saws, you can often get a saw with safety technology that will automatically halt its blade the instant it encounters human flesh. (The process literally takes but a few milliseconds.) The knowledge that your fingers and hands are safe from major injury caused by a rapidly rotating, razor sharp blade is more than convincing enough for many people to invest in these technologically marvelous table saws.


A splitter is a piece of metal that keeps the blade from binding in whatever material you are cutting if the saw kerf starts to close up. The splitter is vertical and sits directly behind the blade. This plays a big part in preventing kickback and should be mounted on the motor assembly so it rises and falls with the saw blades movements. You can also get splitters that can be adjusted to fit the width of the kerf.
The price is acceptable. One cannot say it’s a cheap piece of equipment because it’s not. But, the high quality of production and a great deal of precision justify the somewhat premium price. If you’re a devoted professional, the price shouldn’t be much of an issue for you. The only downside many people reported is the quality control within the company. Many models came with broken or missing parts.
In the commercial construction business, we typically buy a job site saw for each project and use it up during the course of an 18-month job. When these saws hit the site, they are unboxed, assembled and immediately put into use. We rip stacks and stacks of sheet goods with these saws and the tolerances of the cut materials are not very critical. However, that example represents the portable saw use within our commercial crews’ business.

Bigger tables offer more potential for additional extensions. For example, if you’re planning to process a massive piece of wood but you cannot cut it in smaller pieces; a table extension will definitely come in handy. There are a lot of commercial add-ons you can choose from, but you can also construct one yourself if you’re experienced enough. Experimenting with these things never gets old or boring, but keep safety in mind at all times. Make sure it’s completely safe to use the said extension and pay special attention to the amount of vibrations and the overall integrity of the table after you’ve installed the add-on.
Hello, Thank you for your comment. We apologize for any issues our Top Table Saws of 2018 blog post has caused. It was not written to be a comparative review of the different saws but a list of the top saws that we are currently selling. It would be unfair to compare performance of a portable jobsite table saw to a industrial cabinet saw and then also compare them on price. If you would like to read a very good comparative post we suggest you check out ProToolReviews.com. They are not tied to any manufacturers and have a very unbiased opinion.

With this saw, it was a very easy thing to plug it on and get started. The included cord is a reasonable length, but you’ll still need an extension cord unless you happen to be right next to an outlet in your workshop. Raising and lowering the blade is a smooth process and we found the mechanism to be nice and stiff, so you can be very precise with your cut depth. Only time will reveal whether or not this stays tight over the long haul, but it seems to be well-made. Mounting the accessories, like the smart guard system is quick. You just raise the riving knife using the release lever. The riving knife locks into a lower and upper position through the use of two sets of pins. In the upper position it is ready to accept the barrier guard, which you can remove from below the saw. It attaches easily with a lever lock and the anti-kickback device can then be placed on the back of the riving knife such that the teeth are set to grab any wood brought forward by the blade. The physical nature of the barrier guard assembly precludes you from placing your fingers anywhere near the cutting surface of the blade. We (and Bosch) recommend keeping this guard on the saw anytime you are doing “through” cuts. All-in-all, the table saw’s included safety features are more than adequate to keep you from encountering any unfortunate accidents. Removing them, or using the tool improperly, however, will considerably raise your level of risk.
Hybrid saws will often match in terms of power but very rarely have the stability and durability of a cabinet saw, so often they work well in a home work shop where you can add extra stands etc to help. One thing to think about though is that because they won’t be as stable this can often compromise on the quality of the cuts, this is something you must think about when deciding. Read More
This saw has a soft start and also seems to over-rev and then slow down to correct itself upon startup. Strange, and I'm hoping this isn't a precursor to a problem down the road but for now it works fine. The Bosch blade that it comes with was removed and replaced with a Freud. The saw cut like a hot knife through butter and I am very pleased with the overall performance. The miter gauge is a little sloppy in the miter tracks.
The first measurements we looked at with the performance testing was blade speed cutting all three of the test materials. This tests gives us a relative comparison of how much blade speed reduction the motors have under different loading conditions. In our opinion this gives us an idea of how strong the motor/gear box combination is for each saw. For each test we also recorded the “no-load” speed to capture the relative drop in rpm in the blade speed while cutting wood. We used our as-measured no-load speeds instead of the published values from the manufacturers.
From there, the rest of the saws created a top tier of cutting power that wasn’t mind-blowingly better, but definitely noticeable. It took many cuts back and forth between saws to determine which came out ahead of other because they are so close to each other. Bosch’s REAXX took third place overall with SawStop ever so slightly ahead. Part of that simply came down to the fact that SawStop was a little bit smoother cutting. Coming out on top was Ridgid. There was noticeable vibration compared to Bosch and SawStop here, but it was able to muscle through each cut a little bit better than the other two.
home,page-template,page-template-full_width,page-template-full_width-php,page,page-id-4,mkd-core-1.0.2,ajax_fade,page_not_loaded,,table saw theme-child-ver-1.0.0,onyx-ver-1.4.1,vertical_menu_enabled, vertical_menu_left, vertical_menu_width_290,vertical_menu_background_opacity_over_slider vertical_menu_background_opacity_over_slider_on, vertical_menu_background_opacity,smooth_scroll,side_menu_slide_from_right,wpb-js-composer js-comp-ver-4.7.4,vc_responsive
Below is a graph showing the average measured decibels for the saws (for each of the materials we tested). As you can see the saws range from 93.7 db to 97.9 db. OSHA allows 8 hours of exposure for up to 90 db, from 95 db up the exposure limits start dropping quickly starting at 4 hrs for 95 db so clearly these saws all need hearing protection. We ranked the quietest 3 saws as a 2, and the remaining saws as a 3 and felt none should rank a 1 due to the need for hearing protection.
The design is not bad. The height of this particular table saw is around 35 inches. While some people don’t mind it, we think it could have been designed better. However, the best thing about the design is the fact that you can get both contractor and cabinet style table saws in one unit. Dust control is well-designed. The large 4-inch dust port offers a no-hassle setup, especially with vacuums of lower quality. In simpler words, you don’t need to purchase a super-expensive vacuum for this particular unit; any affordable one should do the job well.
×