When I moved to a new home my shop area was radically downsized to half of a two car garage. In my former shop I had a 10" contractor's table saw for over 30 years. I really loved that saw but knew I was going to have to get a smaller saw. I reluctantly purchased the Bosch 4100-09 10" jobsite saw not expecting much. Wow was I wrong. I've had the saw for about a year and a half and use it daily to build medium to smaller sized projects ( boxes, trays, hanging cabinets, end tables). Right out of the box the saw performed well, I had my doubts about doing fine cabinet and furniture work but it is up to the task. I added the TS1002 outside table which is a necessity for larger boards. I also purchased the TS 1007 dado insert. The saw accommodates my freud 8" dado stack up to 1/2" which is sufficient for me. I use only thin kerf blades with a stabilizer and I've had no trouble ripping up to 1 1/2" hardwood. I do have to take it slower than on my contractor's saw but I
It has all the safety features you need. This one has a big, brightly-colored stop button connected to an electric brake, so you can easily bring the blade to a halt. The stop button panel also has a thermal overload switch built in, so it’ll automatically switch the saw off if the motor becomes too hot. We also love that there’s a magnetic switch in the same panel, which prevents the machine from turning itself back on if power cuts out in your shop while you’re working.
Dewalt has refined the DW745's design, most notably improving the blade guard and safety measures. What stands out about the DW745 is its rack-and-pinion rip fence that moves along telescoping rails at the front and rear of the table. This means that once the fence is set square, it should stay square. However, the DeWalt's maximum width for a rip cut is 16 inches, compared to 18 inches for the Bosch. But most users will make large rip cuts with a circular saw, so the 2-inch difference in capacity isn't a big deal.
6. Clamp rip fence to check if it holds securely at front and rear. If rear is not clamped securely, un- clamp fence and turn rear clamp adjustment screw 6 clockwise for increased clamping. Try clamping the fence to verify if it self aligns and clamps tightly at the front and rear. Overtightening of the rear clamp adjustment screw 6 will cause the rip fence to be non-self aligning (Fig. 23). Overtightening may cause friction or “chatter” when fence is moved side to side.
It’s not until you get a bunch of saws side by side in the shop that you start to see the difference between a $300 saw and a $500 saw. While the motors are all 15-amp, the more expensive saws have features like soft start to prolong motor and gear life, electronic feedback to maintain blade speed and gearing to maximize torque. If you look under the saws, you’ll see that the more expensive saws also have much beefier motor carriages and better-quality blade-adjusting mechanisms.
This saw has a soft start and also seems to over-rev and then slow down to correct itself upon startup. Strange, and I'm hoping this isn't a precursor to a problem down the road but for now it works fine. The Bosch blade that it comes with was removed and replaced with a Freud. The saw cut like a hot knife through butter and I am very pleased with the overall performance. The miter gauge is a little sloppy in the miter tracks.

Some previous buyers had motor trouble. Their units conked out early, or worked inconsistently. Apparently, that was down to cheap internal bearings used in the first few iterations of the Bosch. However, according to company replies to some reviewers who cited the issue, the problem has been addressed in the last few versions of this model. We’ve also found that reviews from the past few years are much more consistently positive.
If you’re looking for the best table saw out there, then there’s no better choice than the Powermatic 1792001K PM2000. This is an amazing cabinet table saw that features a 1-phase, 3 HP motor with rout-R lift and Accu-fence system which set a new standard for innovation through thanks to the saw’s large body design and an incredible range of patented features. Almost each feature of the 1792001K PM2000 sets a new standard by which every other cabinet table saw on the market is judged, so you can have the peace of mind that this is not your regular cabinet table saw.

However, with proper use, table saws are generally safe tools, advanced blade stopping technology not needed. Therefore considering a saw without such safety features is fine for the cautious DIY user or for the professional carpenter and/or builder. Take into careful account the actual table size of the table saw you are considering. If you are going to be completing rip cuts in large sheets of plywood, then you need a saw with a table large enough to support these big pieces of lumber.
The power transfer system is neatly done. The model features a serpentine belt which is quiet and smooth during operation. Therefore, the level of noise is satisfactory. Precision is something that makes this model worth checking out. Whether you’re a professional or a beginner, you’ll definitely appreciate the accuracy of this model. On the other hand, with great things come great responsibilities. Don’t forget to wear safety equipment!
Safety is a prime concern for Bosch. From the SquareLock Rip Fence through to the patented SmartGuard System to lessen any chance of kickback, your security and comfort is taken care of. The blade guard and riving knife are quick-release. This takes away any excuse for not putting the guard back in place because it would be too much trouble, something that’s an accident waiting to happen.
As far as the design goes, cabinet saws don’t look much different from the hybrid ones. However, when it comes to sheer power, this type is the most powerful one in every regard. Therefore, devoted professionals who work on massive heavy-duty projects usually prefer cabinet saws over anything else. Each element of a cabinet saw is constructed to withstand a lot of stress and pressure.
We hear the term accuracy tossed around when it comes to finding the best portable jobsite table saw, but we really have to narrow down what that means. Every saw we tested has the capability of being calibrated and it should be the first thing you do after setting it up. Like a new miter saw, blade calibration is simply part of delivering professional results.
DIY-ers love this type due to its simplistic yet effective operation. However, it’s not unusual for professionals to invest in these in order to avoid investing in cabinet models and save some money. Speaking of money, you should prepare yourself for a hefty investment if you opt for this particular type. However, most models are well-worth the money. These things last for years and don’t require a lot of maintenance apart from occasional blade replacements and minor adjustments.  They are not as easy to use as portable models, but you’ll learn how to use them in a matter of hours or days, as long as you follow the rules written in the user manual.

Even though is seems pretty irrelevant, the position of the On/Off switch is quite important, especially if you’re a frequent user of these tools. In today’s models, the switch is usually leveled with your knees. The main thing you should look for is the size of the OFF switch. It has to be big enough so that you can turn the unit off immediately either with your knees, elbows, or hands. The so-called panic button is one of the crucial elements of every unit, even if it doesn’t seem like it.


If you’re looking for the best table saw out there, then there’s no better choice than the Powermatic 1792001K PM2000. This is an amazing cabinet table saw that features a 1-phase, 3 HP motor with rout-R lift and Accu-fence system which set a new standard for innovation through thanks to the saw’s large body design and an incredible range of patented features. Almost each feature of the 1792001K PM2000 sets a new standard by which every other cabinet table saw on the market is judged, so you can have the peace of mind that this is not your regular cabinet table saw.
The first thing you should do before starting up your unit is to check whether you’re wearing all the necessary safety equipment. Gloves are something not many people like to wear. Apart from keeping your fingers safe, they also offer protection against thorns. As you may assume, you’ll work with a lot of thorns flying around. However, gloves aren’t mandatory, and they won’t offer much protection apart from occasional thorns.
If you want to have a quick and accurate cut of wood, look no further than a table saw. When buying a table saw the main thing you put into consideration is its power. A good table saw should have enough power to cut through wet timber as well as hardwood. However, there are certain features which help in foreseeing the overall performance of a table saw.
A gauge will allow you to make very detailed cross and angled cuts. This is a bit of kit that you need to research in great depth as it can make or break the accuracy of your cuts and angles. With a good gauge, you can check blade height, blade angles, miter angles and much more. For further reading checkout Wikipedia’s table saw page and for in-depth air compressor reviews.
For centuries, the job of the sawyer was, quite simply, to saw logs into lumber. Working in two-man teams, a pair of sawyers would use massive saws -- called whipsaws or pitsaws -- to cut felled trees into workable planks with their own muscles as the motive power. The job was exhausting and often dangerous, yet necessary to create the precious lumber used to build everything from homes to railroad bridges.
Another indication of how hard a table saw is working is monitoring the amperage (AMP) draw under loading conditions. We measured the amp draw for each saw using all three materials again at the same time we were recording RPMs. The first graph below shows the amp draw for each saw cutting plywood compared to the no-load amp draw. The white bar on the left indicates the no load amps and the colored bar on the right shows the maximum amp draw during the cut.
For this portion of the testing and evaluation we used three different materials (3/4″ AC Plywood, 5/4 Mahogany Decking, and 5/4 Pressure Treated Southern Yellow Pine Decking) while measuring the saw blade RPM, and the saw motor AMP draw. To compare the saws we’re looking for how much blade speed each saw has under load, and also how much the amp draw increases under load. Think about it like driving a car, a more powerful car will not drop as much speed going up a hill and the engine won’t work as hard.
One of the principal causes of table saw accidents is kickback. This process happens when a piece of wood is ejected at great speed in the direction of the user. Binding between the blade and fence, the wood then gets trapped in the teeth and spat out. A splitter is a vertical blade that holds the kerf open to minimize the chance of kickback. 2 pawls are attached for this purpose.
We spent over 30 hours researching and testing 10 different brands of table saws and found that maximum speed, cord length, and cut depth were most important. The DEWALT DW7480 table saw scored high marks in every category and is our top pick. This 48 pound table saw is perfect for using at home or taking with you to the job site. It has a powerful 15 amp motor and 24” rip capacity that makes it a favorite with everyone. The 2 ½” dust collection port allowed us to connect the saw to a shop vac and reduce the amount of dust that was in the garage.
However, with proper use, table saws are generally safe tools, advanced blade stopping technology not needed. Therefore considering a saw without such safety features is fine for the cautious DIY user or for the professional carpenter and/or builder. Take into careful account the actual table size of the table saw you are considering. If you are going to be completing rip cuts in large sheets of plywood, then you need a saw with a table large enough to support these big pieces of lumber.
The integrated blade carries an electrical signal. Once it comes in contact with human skin, the signal changes because of the skin’s conductivity and the blade immediately stop. Although some people don’t like the process of resetting the blade, it’s quite easy, and it takes only a couple of minutes. If you think about it, it’s better to hassle by resetting the blade for five or six minutes instead of losing a few fingers.
As for extensions, I have added the TS1002 and TS1003 outfeeds (rear and left side respectively) – They do a great job supporting the workpieces without making the saw the least bit tippy. For my use, I don’t get much use from the left side support, but the rear outfeed is great. Much nicer than setting up an outfeed stand and trying to dial it in.

Lowes had a Father’s day sale, on their Kobalt table saw with a folding/rolling stand and was $180.00, with more money off because I signed up for their credit card-so I bought it. It cuts fine, the fence locks on both ends,measurements seem ok, and it unfolds and rolls away very easily-I like it so far. I’m a home owner and I use it sporadically and treat it well, it does not appear to be very robust, so as a day to day, on the job site saw, probably not a good choice. I used to have a Makita table saw, with a terrible fence, unreliable ruler markings, and difficult to use blade guide that interfered with measurements, which you needed to do every time-a terrible saw, very frustrating to use. I have a Makita miter saw and it’s great, but the idea of buying a same brand because I liked one of their other products did not work out.
Perfect for both hobbyists and craftsmen, the PCS31230-TGP252 from SawStop is a 3 HP cabinet saw that delivers excellent performance while featuring the company’s patented safety system to ensure maximum safety during use. The safety system is similar to that of the G0690 from Grizzly where the blade stops in milliseconds after it comes in contact with flesh. Designed and built in order to satisfy the needs of the most demanding users, the PCS31230-TGP252 features an exacting finish and feet and a superior dust collection system. For increased precision and added strength, the PCS31230-TGP252 features a fifty two inch T-Glide fence system, but also an extension table and rails.
You’ll make most of your miter cuts on a miter saw. But when the material you’re cutting exceeds a miter saw’s cross-cutting capacity, you turn to your table saw miter gauge. These usually aren’t quite as precise, but some manufacturers put more thought and robustness into it than others. If you make a lot of long miter cuts, be sure to pay attention to this accessory.
I like the clever design of the stand on this saw which allows it to collapse or open by operating a single lever. The unit has two transport wheels which allows for easier relocation and the stand doubles as a pulling handle. It measures 39 x 30 x 20 inches which makes it pretty compact. The distance between the floor and the work surface is 37.5 inches. To make the stand as durable and corrosion-resistant as possible Bosch has given it a powder-coat finish.
You will need specialty blades for cutting materials such as plywood, masonry, hardwood and metals. Other specialty blades are used for dado cuts. Most dado sets have multiple rows of teeth and chippers and they are typically much wider than traditional blades. Be sure that the model of table saw you have can accommodate the type of specialty blades you want to get so you don’t waste your money on a blade that won’t fit.
Carrying things standing on end is easier, since it makes for a narrower package that can easily fit by your side. You’ll be able to lift a heavier saw less awkwardly in that position than if you were to carry it out in front of you. You’ll also want to think about size in terms of where you need to fit the saw in the vehicle, and where you’ll be storing it when it’s not in use.
The latest advance in table saw safety is a feature that stops the spinning blade when it senses the presence of tissue, such as a finger or forearm. A company called SawStop was the first to offer this technology, and currently, it holds the exclusive right to sell saws with this feature in the United States. (Bosch introduced a portable table saw with blade-stopping technology in 2016, but was forced to take it off the market after a successful patent-infringement suit by SawStop.) In 2017, the CPSC proposed a new rule to make SawStop's technology mandatory on all table saws, but that rule is still under review. See the Buying Guide for more information.
Apart from some short reviews, we’ve also covered some other aspects such as safety and proper use of these tools. Make sure you thoroughly read our articles because they could save your life. The tips we offered are well-known among the professionals, but beginners are always susceptible to various risks, especially if they don’t know how to handle these tools properly.

Jeffery – As Rob explained things we had the RPM measurements running on that meter, and had to watch our video playback to evaluate the numbers (no recording of the numbers digitally). So we tried to take the average no load speed watching the video play back. Is it perfect? No….is a 10% difference a big deal? In this application I doubt it. If we were a full blown testing lab we’d have the data recorded digitally and take full blow averages, but alas we are not.

As with anything, it’s easy to get overwhelmed with the variety of types, sizes, features, colors, weights, what, when, why, where, who…(let me catch my breath). For now, let’s focus on what’s right for you with our Best Portable Table Saw Guide. We’ll start by identifying quality brands that align with your needs. Besides, who wants to buy something that won’t work?
I bought this saw to add to my home shop and a radial arm saw I have had for years. I have owned it since 2009. I bought it after reading reviews in woodworking magazines on line. I did buy the left extension, which I use frequently. This saw has been used for multiple projects, including building furniture, cabinets, cabinet doors and a host of other projects for home, family and friends. It has never let me down, working flawlessly. It has never been out of square. And, yes, I do check squareness every time I use it. Cuts are accurate and the table large enough to manage most jobs without adding an extension. The metal construction is particularly appreciated. The blade is easy to replace, the controls and storage on the unit convenient. What I particularly have enjoyed is the portability and the ease of use of the gravity-rise stand. Being able to move tools around and re-arrange my limited workspace to match the job is important to me. I have read the caveats posted by a number of reviewers, but, in truth, those have simply not been my experience. At 71 with a lifetime of using and buying tools and enjoy woodworking, I count this tool as among one of my better purchases.
Now, don’t get me wrong, there are other portable table saws that are lighter than Bosch’s GTS1031 (who’s name sounds like a cross between a fast production car and a tax document). The key with the Bosch is that it’s jobsite tough. Give the other saws some wet lumber or run them all day long and you’ll smoke the motor, bog them down, or send them off a second story porch in frustration. Bosch seems to have designed the GTS1031 with two things in mind: portability and power. Portability, because all of the accessories store right on-board, and they do so securely, so they won’t fall out, even if the saw is bumped and tossed around – as jobsite saws tend to be.
Outfeed capacity is almost always the depth of the table. Pros using a jobsite table saw can opt to put a sawhorse or other support to hold the material after it passes the blade. There are a few models running around that give you some extra outfeed support, though. Most of the time, you’ll just have a buddy help guide the cut through from a safe stance on the behind the saw.
My intention with this website is to provide you with everything you need to know about table saws. I have tried to remain as objective and as informative as possible, and I hope you will be able to tell that when reading the reviews. Hopefully, you will find them helpful when it comes time to choose a table saw for your workshop or home. Good luck and take care.
It has a machined aluminum table which is extremely precise. We like the Dewalt’s cast metal table for the price, but the company don’t list the material, and we suspect it’s not nearly as rugged as aluminum. The Bosch’s table is much better. It’s rugged, sturdy, and more consistently even than the Dewalt. The table makes this one a smarter choice for fine woodworkers or pros who need superior alignment.
The cabinet itself is 19-3/8-inches deep by 19-3/8-inches wide, which makes it the same size as the last SawStop model we looked at on our list of the best products. Included with this cabinet is a 20-inch by 27-inch cast iron table that extends out from the cabinet. This table is durable enough for regular use and will give you more space for working.

home,page-template,page-template-full_width,page-template-full_width-php,page,page-id-4,mkd-core-1.0.2,ajax_fade,page_not_loaded,,table saw theme-child-ver-1.0.0,onyx-ver-1.4.1,vertical_menu_enabled, vertical_menu_left, vertical_menu_width_290,vertical_menu_background_opacity_over_slider vertical_menu_background_opacity_over_slider_on, vertical_menu_background_opacity,smooth_scroll,side_menu_slide_from_right,wpb-js-composer js-comp-ver-4.7.4,vc_responsive
×