We were impressed with the Bosch Glide Miter Saw which was revealed in 2010 and revolutionized the depth required by a saw in close quarters. Building on their solution-based approach to products, the company has finally addressed the need for a truly portable full-power jobsite table saw. The Bosch GTS1031 table saw can be carried by its single handle, which is balanced in the middle, and all accessories are safely and securely stored on-board. This was demonstrated wonderfully by none other than Jason Feldner at the 2011 Bosch Media Event, who came running into the room with the Bosch GTS1031 table saw in one hand and a GTA500 stand in the other. Weighing in at a manageable 52 pounds, and this is one 15-amp jobsite table saw that does a great job of balancing portability and raw cutting power.
The Bosch weighs in at 52 lbs. While you could carry it one-handed, and it feels well-balanced, it would throw your personal balance way off and tire your arm. The DeWalt is a little lighter at 45 lbs., but it feels even lighter than that, and its weight distribution makes it feel less fatiguing to carry back and forth. (You can also carry the Dewalt saw one-handed by its handle or roll cage, but you probably won't want to.)
You should test the cutting depth of a saw when it is not cutting a bevel. This aspect helps in determining accurate and maximum cutting at 0 degrees. In considering bevel cutting, you should ensure the base plate is adjustable. Look out for adjustment allowance that your saw offers you such as 45, 50 or 90 degrees. The table saw should also be a feature with the flush housing so as to allow the table saw to cut very close to the edge of the wall. It is necessary to look out for this feature as will allow you to cut flooring to size at ease
Belt drive table saw motors run on a pulley system, most of the time some power is lost through this system, but belt drive blades can cut through thicker timber and hardwoods. They can produce power of around 3 to 5HP and thanks to the motor being mounted further away from the blade with belt drive, the motor will last longer as less dust will get into the motor. One thing to consider though is that belt drive will be in general more expensive and are normally found on heavy cabinet type saws, so this must be considered when working out your budget.

Whether your household’s resident handyman dabbles in amateur woodwork or takes pride in his DIY repair jobs, chances are he doesn’t need a high-end table saw to take care of his most basic needs. The Ryobi 15 Amp Table Saw is the ideal example of a machine that packs a load of must-have features you’d find in a higher-end table saw at a fraction of the price of competing models.

The DEWALT DW745 and the Bosch 4100 both have 15 amp motors, so power shouldn’t be a problem with either of these job site table saws. The DEWALT has a high torque motor that is capable of delivering a no-load speed of up to 3,850 rpm. The Bosch 15 amps and a no-load speed of up to 3,650 rpm. The difference between the two is not something that would be noticeable without sophisticated equipment, and will not affect performance in any significant manner. The noticeable difference between the two is that the Bosch 4100 comes equipped with a soft start motor that is lacking on the DEWALT DW745. This will cause a noticeable load on your power source, and may affect other tools and lighting attached to the same source during startup.
As mentioned, the look is similar to a hybrid with a full enclosure. Looks can be deceptive, though… The core design purpose is for this saw to stand up to constant heavy use in a commercial setting. This is not a tool you buy for casual woodworking at home.These bulky, heavy units are built to last the distance. They can weigh up to 500 pounds. You’ll get an accuracy and rigidity not available in lesser types of table saw.Other table saws call for regular adjustments. With a cabinet saw, you won’t need to do this as often once it’s set up properly. 240V motors developing 3-5HP mean there’s very little the best cabinet table saw won’t rip through with ease. Large sheets of hardwood are no problem at all.
We absolutely love the Dewalt DWE7491 that we recommended as our top quality choice above. It’s a powerful, precise workhorse that can handle nearly any cutting job. However, times are changing fast, and workplace safety standards are increasing just as rapidly. If you’re a professional who wants to stay on top of your code, you should consider getting a unit that’s equipped with a flesh-detections safety system.
Welcome to the heart of this website – my selection of the best table saws for several specific needs. You see, it’s impossible to select only ONE as the best for all purposes because a table saw should be carefully tailored to your needs. There’s no point in buying a complex cabinet saw if you’re a beginner, you’re probably better off with a solid benchtop saw. The same goes if you’re a professional, only the other way around.
In terms of cutting results, Craftsman’s 28463 Jobsite Table Saw made a decent showing. It delivered accurate rip cuts, kept its bevel setting for angled ripping and could handle a stacked dado blade without laboring. Dust collection through an enclosed shroud was on par with more expensive machines. I also appreciated the saw’s clear, split guard and a riving knife system that is easy to install and adjust up or down. These are the plusses of what, in this test, is the budget-priced tool.
Due to the position of the motor, dust collection is often an issue with these units, especially in comparison to the cabinet type. However, an industrial vacuum is usually a small and worthy investment which should solve the issue effectively. The main advantage of this type is the fact that it’s much cheaper than its nearest equivalent – the cabinet type.
Speaking of safety, this particular model offers a satisfactory level of it. First of all, the tool-free adjustments come in handy if you’re in a middle of a project. In case you need to make a quick adjustment, you don’t have to stop whatever you’re doing and commit your attention to fine-tuning. Instead, you can do it on the go, without any additional tools. Furthermore, the convenient guarding system keeps your fingers and hands safe at all times. Don’t forget to wear protective gear; it can make a difference between life and death.
After cutting a bunch of wood with this saw, we really liked the balance of power and portability of Bosch GTS1031 – and I think that’s what this saw is all about. For raw Performance, the unflappable motor-blade combo earned a stiff 8/10 in our tests, while its affordable $399 price tag put it at a solid 9/10 in our Value scale. Sure, you can get cheaper portable table saws, but you’ll find it a challenge to track down the combination of power and portability the Bosch GTS1031 offers. Bosch’s gravity rise-equipped 4100-09 remains a compelling alternative or those wanting an integrated stand. It occupies an additional 15″ in width and 8″ in length and is a full 3.5″ taller. But it only tacks on 8 pounds in weight. If you’re cutting larger pieces of wood or need a saw with a stand, the 4100-09 may be your baby, but the new Bosch GTS1031, with its “toss it in the truck” form factor is our new sweetheart tool. While it has an available GTA500 folding table stand accessory, the real advantage of this saw is it’s stand-free portability – so don’t make it into something it’s not. After using this tool, we think you’ll want to take it with you, as-is, just about everywhere!

The fence on this system is easily the winner. With clamping on just the front side, it self-aligns better than any other in the group and offers excellent stability. While SawStop didn’t have the most powerful feel to the cuts, it was very smooth with little vibration. Feature preferences aside, the only (slight) negative we agreed on was that the bevel lock stuck a little bit compared to others.

Not everyone needs to use the miter gauge on a table saw since there’s typically going to be a miter saw around. If you do, you’ll like the positive locking detents at common angles. This saw felt like it was the weakest when pushing our 2x PT material through. Despite the ranking, it doesn’t feel under-powered – you just need to take your time. You won’t find a lot of bells and whistles on this model, but for $279, we don’t have many complaints.
The DEWALT DW745, due to its smaller size, does not have the capacity to use a stack of dado blades (blades designed to be stacked together to make wider cuts, grooves, and notches). It has also been noted that the plastic miter handle is a weak point, and it limits accuracy. There are no available table extensions. It does, however, come with a three year manufacturer’s warranty.
All table saws sold in the U.S. come with a riving knife, anti-kickback pawls, and a split blade guard. Because some cuts can’t be made with these safety features installed, they are removable. If you’re looking for a fun party game, see who of your uninitiated friends can install both correctly without a manual. While each one is different, their nature means you can use the saw without them installed. I’d be remiss if I didn’t tell you those cuts are more dangerous, so avoid it if you can.
Most table saw blades come in 8, 10 or 12inchs in diameter, but you can also get a lot smaller and larger sizes if you require special cut sizes and cut depth sizes. When looking for a new blade when it comes to sizes, blades are measured in two sizes mainly, the mounting hole and the total blade diameter, make sure you take the mounting hole size in to consideration when buying a new blade as this could be something very easily over looked but could cause an issue.
The cabinet also has a few other safety features that set it on a level above the Grizzly or Jet. There’s an extra-large, paddle-style power switch which you can easily press with a thigh as well as a hand. The guard works tightly against the blade, so that you have all the workspace you need without sacrificing safety. The riving knife prevents kickbacks, and the left-tilting bevel feature prevents binding.
I appreciate the helpful comparison of the best table saws. I’m fairly new to woodworking, and until recently I was using an old table saw that used to belong to my dad. Long story short, it’s no longer usable, and so I’m looking for a good table saw to buy that’s beginner-friendly. I have my eye on the DEWALT DW745 – evidently it’s really popular and does a great job. I’ve taken a look at some other sites for more ideas. Your guide here is great. What is your opinion on the DW745?
We’re loving the guard system on this Bosch. It’s modular, like the Dewalt’s, so you won’t have to use any tools to set it up, take it down, or make adjustments. Like the Dewalt, this unit has a clear guard, with independent panels, kickback pawls, and a riving knife. The riving knife on this one is a standout feature for us, since it adjusts to three different positions, depending on what kind of cut you’re making. It’s a smart design tweak that saves you needing to have several differences riving knives

About three paces from where I tested these portable table saws sits my late-model cabinet saw. As a serious woodworker and magazine editor, I can’t imagine not having it. Its powerful 3hp motor, spacious cast-iron tabletop and almost hair-splitting precision makes most other saw options pale by comparison. But all this said, a cabinet saw isn’t everything. The thought of moving that behemoth down the steps to a basement shop sends chills up my spine. I sure can’t toss it into a car trunk to help a friend down the road. My saw takes up a huge footprint of shop floor, and it cost a small fortune. I don’t know of any stationary table saw that sells for less than $700 new these days, and that can empty the coffer of a modest tool budget.


One term you may hear when reading about table saw accuracy is blade runout. Runout is a term that describes whether or how much the outside edge of a saw blade wobbles while being held by the motor shaft. Sometimes, operators measure runout by using a saw blade. In that case, the very use of a saw blade presumes that the specific blade is perfect or nearly perfect in its flatness. Using a saw blade that has any warping will not give a clear indication of blade runout.
The only dislike that I have found about the Bosch 4100-09’s operation is that unlocking the table causes a tab to pop up above the cutting surface. This tab interferes with the operation of the fence, and could lead to damage of the product. It also comes with only a one year warranty. It does have available rear out-feed extensions available, to help facilitate larger work pieces.
This is a truly great saw, except that it is really tough to adjust the blade and rip fence for parallel. Once adjusted though, it is a fine piece of engineering. What I like best is that the saw is built for the job site. It is extremely beefy, but no too heavy. In my opinion, it strikes a nice balance. Its cart stand is the best in the industry, bar none. Once adjusted, the saw returns to its settings extremely well. It is obviously built for the long haul, and should last a contractor many years. I would definitely purchase this saw again. Now with the things that I wish were better. First, adjusting the blade for parallel is just plain hard. Mine was out from the factory by 4 thousandths. It is a trial and error process, and the instructions suck. Here's what to do: 1. Loosen the four screws indicated in the instructions. Starting from behind the saw, center the blade housing in the rear left to right as best you can, then tighten one screw not quite snug (you want the housing to rotate on this screw when you adjust the front). Next move to the front of the saw and loosen the lock lever for blade angle adjustment (the housing won't move unless you do). Now, begin experimenting with holding the housing at 90 degrees with one hand while sliding the housing back and forth with the other until square. When you think that you are close, lightly tighten one of the front housing screws. Check for parallel (look for videos on how to check a table saw blade for parallel), then tighten the blade angle adjustment lever. With these screws and the lever tight and locked, check again for parallel. If it is still good (I got it to 1/1000 inch of parallel), then lock all the screws and check one more time, if it's still good, then you are done with blade housing adjustment.
These saws are the most difficult ones to categorize. The simplest explanation would be that they are somewhere in the middle between contractor and industrial cabinet saws. They are driven by an inboard belt motor. These units usually have open leg stands, but there are some models with closed ones – hence the whole confusion and difficulty in categorizing.
From there, the rest of the saws created a top tier of cutting power that wasn’t mind-blowingly better, but definitely noticeable. It took many cuts back and forth between saws to determine which came out ahead of other because they are so close to each other. Bosch’s REAXX took third place overall with SawStop ever so slightly ahead. Part of that simply came down to the fact that SawStop was a little bit smoother cutting. Coming out on top was Ridgid. There was noticeable vibration compared to Bosch and SawStop here, but it was able to muscle through each cut a little bit better than the other two.
SawStop PCS31230-TGP252 10 in. 3HP table saw is a high performance cabinet table saw that features a durable cast iron table, 44 x 27 in. of total space, and is super durable, making it an ideal table saw for professionals. In addition to its industrial capabilities, this SawStop table saw also boasts a couple other practical features including a Flesh Sensing Technology, dissipative arbor belt to prevent hazardous charges, and an easy-to-change brake cartridge.
When I switched blades, I did find the locking lever for the riving knife very stiff … not sure why. It raises to release the riving knife and pushes down to lock it. I resorted to gripping the lever with a pliers to manipulate it, after nicking some skin on the blade teeth. But, on the softer side, RIDGID provides a nice complement of overmolds on the miter gauge handle and blade height handwheel knob.

Paul – Good catch….I’ve updated that to say Skilsaw not SawStop…thank you! As you can imagine…all the data makes it tough to keep it all straight. I’m not even sure how you’d install that aftermarket fence on these saws. If you do I’d love to see how!! Those really look like they are made to install on cast-iron full size saws. I’d choose the DEWALT with a slight edge over the SKilsaw.
The old designs of table saws did not have the angled capability that newer models have now with their ability to have the blades angled at 45 and 90 degrees. Before these upgraded styles, the table itself had to be tilted which made cutting extremely unsafe. The new styles that accommodate angling the blade for the beveled cuts make things much easier and safer for the user.
Looking for a better way to take care of your wood cutting and still attain a professional result from the comfort of your home? Skil table saw with folding stand will provide exactly that. The foldable stand makes it convenient for any room use and storage. When the table saw is not in use, you can fold it right and use the space for other activities. It’s therefore suitable for small space users who are interested in professional cutting. Another interesting factor about Skil table saw, is that it cuts through materials that are 4 times the normal size. Therefore, instead of cutting each piece individually, you can set several materials to reach the height capacity for easy cutting. Additionally, the fence of this saw will guide and balance your material for accurate results. The saw also features huge blade to make the work easier and interesting for every user. If you invest in Skil saw, you will not only control your cutting but also upgrade your work to the level of expertise even if you are just starting off.
×