I can’t tell you how many times we’ve pulled out other jobsite saws only to have accessories fall off, or require off-tool storage. Bosch designed the GTS1031, however, to securely hold all of its accessories, even including the arbor wrenches (both of them) and an allen wrench for adjusting the riving knife and dust ejection points among other things. Our favorite was the rip fence, which simply flipped upside down and stored underneath the table – clever! About the most difficult adjustment was the riving knife, which is a tool-less maneuver, but one which requires you to stick your hand way into the blade cavity to reach the release lever. When making any adjustments to the blade, it goes without saying (but we’ll say it anyway) to disconnect power to the saw as a precaution.
For any kind of professional woodworking and large scale construction work, the cabinet table saw is the one for the job. These types of table saws are often called stationary saws. The motor is protected in a cast iron and steel cabinet that reduces noise and vibration as well. With reduced vibration comes better accuracy which is always the desired effect, especially for professionals. The motor us a powerful 3-5 hp and requires a 220-volt outlet. If you are using it in a home workshop, a special outlet may need to be installed if 220s are not already installed in your garage or shop. Measuring about 28” x 43” and weighing in at over 400 pounds, these table saws were not designed to be portable. The large work surface is ideal for cutting large pieces with ease. Cabinet saws can use a 12” blade with no problem, although a 10” blade is the most commonly used. It is the most expensive of all of the styles of table saws.
Move the wood to and then "through" the spinning saw blade slowly and steadily. It's alright to use your hands while you're still at least a foot or so from the blade, but once the end of the board or sheet nears the blade, you should use a pushing stick to keep the wood moving and to keep your fingers away from the blade. Even an experienced carpenter can have a lapse in concentration or a slip that can lead to serious injury.
From the triple belt drive system, to the three-HP motor and the large cast iron table and wings, the Shop Fox W18193 s built like a tank. You’re also going to love the T-slot miter gauge that features a fence extension and flip stop, but also a four inch port for dust collection and camlock T-fence. There’s also a twenty nine and a half inch rip capacity.

The DeWalt will do you proud for a broad spread of applications. If you’re a home woodworker, you’ll be able to rip sheet material, size material as thick as 3 inches, frame lumber and make cross cuts to your heart’s content. For professionals, the DeWalt is perfect for trim carpentry, installation of hardwood floors, decking or remodeling. There’s very little you can’t do with this beast.
Editor’s Note: If you’re using the Bosch REAXX saw without dust collection, you’re going to want to partially open up the clasp located on the bottom of the saw. This allows the sawdust to exit the blade chamber through a half-inch gap. Failure to do this will clog the output port in a very short amount of time. When you use a dust extractor you can keep this chamber fully closed.

If you want to take the saw with you and use it in a different location, you can purchase the optional MB-PCS-000 integrated mobile base which features 2 stationary casters and 2 pivoting casters. Furthermore, it’s also possible to upgrade the mobile base assembly to a one thousand pound lift capacity, add a hydraulic piston lift and 4 independent pivoting casters.
Safety and precision are usually at a high level. Some models even offer a sliding table as an option to mitigate cross-cutting. Needless to say, hobbyists love the sliding feature because it saves a lot of time and most importantly – nerves. As far as the driving mechanism goes, there are three possible options – single V-belt, serpentine belt, and a multiple V-belts.
It has a machined aluminum table which is extremely precise. We like the Dewalt’s cast metal table for the price, but the company don’t list the material, and we suspect it’s not nearly as rugged as aluminum. The Bosch’s table is much better. It’s rugged, sturdy, and more consistently even than the Dewalt. The table makes this one a smarter choice for fine woodworkers or pros who need superior alignment.
This is the smallest of all the table saws, typically weighing about 50 pounds or so and designed to sit on top of a table or workbench. Bench style table saws are usually made of steel, plastic and aluminum. They are good for light to medium duty cutting and would not be a good choice if you do a lot of cutting or if you have a professional business. Because it can be lifted by one person and moved around with relative ease, this type of saw is often called a portable table saw. Due to the size of these saws which measure approximately 19” x 27”, they are not designed to rip large pieces of wood. It is also not easy to make mitered cuts. You will notice that there might be more vibration when using this saw as compared to other, larger models. This is due to the lighter weight of the saw. Unfortunately, the vibration can affect the accuracy of the cuts you’re making.
It’s easy to use, quite safe, and most importantly – it’s a high-quality piece of equipment for a more than reasonable price. If you don’t like what you see, don’t hesitate to read some of our other reviews, there might be something of interest for you. As far as this particular model goes, it should turn out to be a worthy and cost-efficient investment. In the end, it all comes down to your personal preferences.
One thing you must be aware of with a contractor saw is the fact that they can be a lot more difficult to move from job to job, this is something that must be considered before purchasing. For thicker and harder type woods a cabinet table saw maybe the best way to go, especially for the long-term benefits, but for the average mid-sized contractor it’s still a great option. Read More
Plus, it’s simply a great table saw in its own right. It’s powerful, efficient, and quiet. It cuts through all kinds of stock smoothly and easily, and the dust collection system helps it clean up after itself. Previous buyers who upgraded to this one said that the transition from their old cabinet units felt like switching from a family sedan to a sports car. We recommend it to anyone looking for the absolute best quality, for small to midsize pro shop work or the passionate home woodworker.
First off, consider how often you’ll put your table saw to use. If you work in the fields of contracting or carpentry, there’s a chance you’ll be using your new machine pretty often — so you may as well invest in a more expensive, heavy-duty table saw that’s sure to last longer than the average model. On the other hand, hobbyists and weekend woodworkers won’t need a pricey piece of machinery — a more compact and inexpensive model should do just fine, especially if you’re only working on smaller projects like birdhouses and DIY wooden models.
You can opt to extend the warranty coverage to 3 years, all through an external provider. We actually prefer these third-party warranties for power tools because they allow you to deal with people who are on your side, as opposed to company representatives, who can be frustrating to say the least. We think add-on coverage is a great safeguard for any cabinet table saw, and it’s a very reasonable proposition on this model.

One thing you’ll love about the riving knife is that it allows for adjusting the table saw without using any special tools, for non-through and through cuts including, pictures frames, grooves for shelves, but also cheek cuts for furniture, rabbets and dadoes. There’s also the possibility to store different tools or anything else you may find under the tablet board and given the fact it’s expandable and convenient, it’s going to make using the Delta 36-L552 an even more amazing experience. For dust collection, the table saw comes with a bi-level dust extraction system which offers superior dust collection capabilities.


Overall, I really like this saw. I have used it for trim work, and for cabinetry work. I worked for a guy who had the older model (the 4000) which is pretty much identical except that it does not have a riving knife (best safety upgrade ever) and it is still going strong after well over a decade of daily use. I wish there was more table in front of the blade, and I wish the dust capture was better, but it is a tremendously good saw and I consider it (with the addition of a track saw for full sheet handling) to be a viable alternative to a big cabinet saw.
If you work with wood in any capacity, chances are you rely on a table saw to make clean, accurate cuts. But when your good old saw goes to the big toolshed in the sky, it’s time to opt for a replacement. Before you dish out your hard-earned money on the first model you come across, remember that a table saw is a big investment, so it’s in your best interest to look into the many technical specifications of each option before you settle on a final purchase.
Table saws cut more or less the same way as a circular saw (covered in their own report): a round blade, usually 10 inches in diameter, spins as it works its way through the wood. The main difference is that the blade is fixed in place, sticking up through a gap in the table, and the operator moves the wood past the blade instead of moving the saw itself. Table saws support and guide lumber and wood panels as they pass over the spinning blade, making it easier to make accurate repeat cuts than with a circular saw.
The saw’s table measures 29 x 21.5 inches which makes this unit suitable for the fabrication of large sheets of material and large wood stock. The table is made out of aluminum and is really smooth which means you will be able to slide even the largest pieces in with very little effort. Still, for extra safety, I would recommend the optional extensions when ripping longer workpieces.

The miter gauge gets an “its fine” grade. Ok to support a narrow piece for a crosscut, but not long enough to do much more than that. I upgraded to an Incra miter 1000SE and never looked back. Although a crosscut sled is pretty easy to make (and I highly recommend getting one) I picked up an Incra Miter Express sled for real cheap at a garage sale, so I am happy to use that.
Another important safety feature to consider is a magnetic switch. Magnetic switches are there in case of power cuts or outages and will also protect the table saw motor from over load. Effectively it will switch off the power supply the instant the power goes off ensuring you don’t have a saw blade spinning away in the dark! As you can imagine this is a very useful and must have safety feature when looking to purchase a new table saw.

I definitely give this one 5 stars, but this is specific of the application – it being portable. If I was comparing it with other Hybrid saws, than this one doesn’t really compare when it comes to power. That being said. I was shopping for a table saw, after many years of working with a circular saw, and a straight edge – for me – it was time to get a setup for repetitive cuts that would be easier, and less time consuming (not to mention more precise, as the machine...
The Steel City 35955 also comes with a new table insert system, a seamless table top that offers users a flat surface on which they can work on, but also the Push Stick safety system which prevents injuries to the fingers while using the table saw. Warranty wise, you get 2 years limited warranty, which is enough to give users peace of mind that they’re covered for a long time.
Ridgid notches a third place finish as the only saw to include an independent blade height lock. The adjustment wheel raises and lowers with multiple full turns like most saws, but integrates a lock into the center. For the bevel adjustment, the outside of the height adjustment wheel turns a rack and pinion style system to accurately change the blade angle – a feature Makita shares.
When the blade touches flesh, a brake will stop the blade and the blade drops down below the surface of the table. The operator will presumably leave with only a small nick or no injury at all. These systems definitely bump up the price of the saw, but it’s a major safety feature and just might be able to save you some very expensive medical bills, along with your fingers.
6. Clamp rip fence to check if it holds securely at front and rear. If rear is not clamped securely, un- clamp fence and turn rear clamp adjustment screw 6 clockwise for increased clamping. Try clamping the fence to verify if it self aligns and clamps tightly at the front and rear. Overtightening of the rear clamp adjustment screw 6 will cause the rip fence to be non-self aligning (Fig. 23). Overtightening may cause friction or “chatter” when fence is moved side to side.

The more table size you have, the more support you have which is always a plus, not only for convenience but safety too. There are right side extensions that can be purchased for table saws that increase the table saw’s capacity to get to the center of a 4 x 8 sheet of wood. Although most saws have a rear band that supports the wood as it exits the saw, an additional safety measure is to rig up an outfeed support of some kind in addition to this rear bar. Be sure that the outfeed support you set up is ¼” lower than the table saw is.
If the blade you purchase has a .092” kerf (i.e. Irwin Marathon 80T, FreudLU83R010) you will most likely have issues with binding on the back end of the cut. To be safe, find a blade that has a kerf of around .098” (i.e. Freud Avanti TK905 50T) and this should take care of the problem. You should also take note that every blade Bosch makes should also work with the Bosch 4100-09.

One of the things we looked at was the ease of assembly out of the box. We had the same person assemble each of the saws and timed the assembly to see if there are any significant differences between the models. The assembly time for the saws ranged from 21 minutes to 48 minutes. While some stands required more than twice the time, we felt the assembly time was not a significant enough factor to change someone’s mind on which saw to purchase.

With a 32½" rip capacity and motor capable of up to 4800 rpm, the DWE7491RS is more than prepared to effectively deliver 3⅛" deep cuts to thick slabs of wood. Happy customers sing this machine’s praises, reporting that it’s as sturdy as a table saw can get — plus, it’s easy to use, and assembling it is a cinch. They do however note that workers looking to produce finer cuts should seek out a replacement blade since the one provided is more suited for fast, rough work.
Powerful cutting and portable convenience with the Delta Powerful cutting and portable convenience with the Delta 36-6022. The 1-step release stand and large wheels make it easy to move the saw to any jobsite. The 15 Amp commercial grade motor cuts through the toughest materials. UL approved 3-way guarding system with riving knife for safety and excellent dust ...  More + Product Details Close
There were really two major performance considerations we wanted to look at to help determine the best portable jobsite table saw: cutting power and dust collection. Power is an obvious choice. We want to make clean, straight cuts, but we don’t want to spend all day making them. Any saw can be calibrated to be straight and accurate, but some have to be babied more than others to get professional results.
Give yourself a reason to be proud of your job by bringing in a table saw that has what it takes to get quality cutting. Just as the name, Powermatic table saw will ensure your cutting is accurate and interesting. It has a poly-v belt, which maximizes motor efficiency and reduces vibration for noise-free performance. The table saw also features massive dust collection to ensure your working space is clean and accommodative. With 30” Accu-fence system, nothing will be impossible to handle. Additionally, the entire unit is designed with quality material for longevity. The design is also portable making it easy for you to move from one job site to the other comfortably.
×