The whole thing is a bit more versatile than the Dewalt, thanks to expanded fence rails and an extended trunnion set. It has a wider rip capacity than the Dewalt. This one uses a traditional sliding-rail fence which gives you a rip capacity up to 25 inches. The fence locks at either side, like the Dewalt’s. It also has a wider bevel range, tilting up to 47 degrees.
Kobalt’s KT1015 Table Saw features value pricing with a decent rolling stand. We initially had questions about its dual-locking fence, but found that it actually worked quite well. There’s plenty of wobble in it, but if you follow our Pro Tip on adjustments in the fences section, you can lock the front end in square then stabilize it with the back lock.
If you work with wood in any capacity, chances are you rely on a table saw to make clean, accurate cuts. But when your good old saw goes to the big toolshed in the sky, it’s time to opt for a replacement. Before you dish out your hard-earned money on the first model you come across, remember that a table saw is a big investment, so it’s in your best interest to look into the many technical specifications of each option before you settle on a final purchase.
The riving knife and blade guard actually have a quick-release so you can easily remove it. This is important because, in the past, these elements were so hard to install once removed people would simply leave it off. Now that there is a quick-release feature it makes it much easier to put back on and avoid the involuntary donation if OSHA decides to visit the job-site.
The blade is a 24 tooth carbide tipped blade that is durable and long lasting. You can even adjust it to a 45 degree angle for those more difficult bevel cuts. If you’re working on uneven ground, you’ll love the rear feet that are fully adjustable so you can level you work space. You’ll get a lot of use out of the onboard storage that will give you easy access to the push stick and guarding components. Weighing only 45 pounds, you can move the table saw from work site to home with ease.
While you may be tempted to skip straight to the reviews, they are a bit on the technical side and contain plenty of terms you might not be familiar with just yet. My suggestion would be to start by reading the informational articles which will provide you with a decent amount of knowledge on table saws. After that, I sincerely doubt you would be caught off-guard while reading anything in the review section.

In terms of features, the SawStop ICS51230-52 comes with a patented safety system that prevents injuries and serious accidents and offers users the highest level of protection during use. Thanks to its 5HP, you can easily cut hardwood of 5 inches or even thicker without having to worry about the saw choking. Also, thanks to the toll-free fast change mount, you can transition between riving knives and guard in just a few seconds.


Today's table saws also include riving knives, which ride up and down with the blade when its height is changed, rather than splitters that are fixed in place. The problem with the old splitters was that they had to be removed for certain types of cuts, and users might forget to put them back on before making rip cuts. This increased the risk of kickback injuries, which occur when the spinning blade kicks back a piece of wood toward the user with tremendous force, causing serious injury to any part of the body that's hit.
From dust collection and onboard storage through to on/off switches and table extensions, most reputable table saws come equipped with everything you’ll need to rip up the wood of your choice. Whether it’s making your life easier with wheels enabling height and tilt adjustment or a safety feature like the magnetic switch, the functionality of table saws is impressive. You can upgrade the blades, get various jigs or dado blades and generally enhance the way your saw performs.
We evaluated the flatness of the table by measuring the flatness by placing the edge of a precision ground flat bar across the table and placed feeler gauges in any gaps to measure any difference between the ground bar and the table. TBB took measurements in four directions. As the operator faces the saw, we measured the flatness at the arbor from front-to-rear; we measured the left-to right flatness at the arbor; we measured the flatness from the upper left-to-lower right table corners; and, finally, we measured the upper right-to-lower left flatness between the corners.
While your table saw is unplugged, take the time to clear and clean the work surface, removing any debris that could negatively impact the smooth path of the wood you will be cutting. Then, lower or raise the blade to where the blade gullet (the curved section between each blade tooth) is equal with the top of the piece of wood to be cut. Also, make sure that your saw's dust exhaust port is clear and open and that a bag is in place to catch any excess sawdust.
The service coverage under the warranty requires you to either bring the machine to an authorized dealer or ship it back to the company on your dollar. That’s a major downside, and it’s one reason we’re recommending purchasing add-on warranty coverage for this one. If you’re dealing with a third party provider, you can simply get a replacement without having to go through frustrating company reps.
Buying a table saw is one of the biggest and most important purchases you will ever make when it comes to power tools. It is an integral part of most job site equipment, as well as an essential item for most do it yourself projects. Choosing a table saw that fits your particular needs and budget can mean the difference in both profitability and frustration level.
Like the Grizzly, the Jet has a standard 4” dust port coming out of the cabinet, and a 220V wiring box for you to attach a power cord. The Jet is also a more shop-friendly tool, since it has much better dust collection. That’s thanks to a fully-shrouded blade and a guard which handily deflects sawdust into the vacuum channel, rather than off to the side of the table.
While I appreciate this review, that Kobalt job site saw is the absolute worst. Uncontrollable blade wobble, terrible fence, trundle bolts that are nearly impossible to get to without tacking the back panel off (of course that doesn’t matter when the blade won’t stay in alignment for more than a day), miter slots that aren’t parallel to each other and also taper toward the backside of the table, and a riving knife without adequate adjustments to align it with the blade. Do not buy that piece of garbage.
This Portable Table saw includes an industry standard This Portable Table saw includes an industry standard tool-free split guard design that allows a true rise-and fall riving knife by using a lever on the inside the throat plate. It has a Tool-less assembly for the riving knife and anti-kickback pawls. It's perfect for mobile contractors and the Do-It-Yourself ...  More + Product Details Close
Safety and precision are usually at a high level. Some models even offer a sliding table as an option to mitigate cross-cutting. Needless to say, hobbyists love the sliding feature because it saves a lot of time and most importantly – nerves. As far as the driving mechanism goes, there are three possible options – single V-belt, serpentine belt, and a multiple V-belts.
The Bosch 4100-09 10 In. Worksite Table Saw with Gravity-Rise Wheeled Stand delivers both professional rip capacity and outstanding portability for a tool that can get the job done, wherever it is. The powerful 15-Amp saw delivers 4.0 max HP for outstanding productivity. It also incorporates soft-start circuitry for smooth but quick ramp-up to the operating speed to manage the intensity of motor start-up and minimize the possibility of tripping a circuit breaker.. It includes Constant Response circuitry to help maintain speed under load, and overload protection. The Square Lock rip fence is engineered for maximum trueness and great ease-of-use, with the fence able to easily glide along the rail for one-handed operation. The lighter GTA47W Gravity-Rise Wheeled Stand has 8 In. treaded rubber-composite tires and a single-action design for easy set-up and transport. It is jobsite-ready with heavy-duty construction. The Smart Guard System is the first modular table saw blade guard, featuring a three-position adjustable riving knife, anti-kickback pawls and non-obstructed-view barrier guard assembly. The table saw provides a 29 In. x 21-1/2 In. square tabletop with a 25 In. rip capacity for ripping 4 Ft. wide sheets goods in half.
Cutting a board to length by using the fence as a guide is one of the most dangerous yet very common techniques. The fact that it’s quite common among DIY-ers doesn’t make it safe. In fact, it’s extremely dangerous and can lead to fatal consequences. There is a high risk of kickback if you’re using this particular technique. Needless to say, the forces involved are immense, and you’ll end up with a piece of wood in your face. One could say – “But, I’m wearing safety goggles!” Even though it may be true, goggles won’t do much against a dense piece of wood flying straight to your face a few hundred miles per hour.

Speaking of safety, this particular model offers a satisfactory level of it. First of all, the tool-free adjustments come in handy if you’re in a middle of a project. In case you need to make a quick adjustment, you don’t have to stop whatever you’re doing and commit your attention to fine-tuning. Instead, you can do it on the go, without any additional tools. Furthermore, the convenient guarding system keeps your fingers and hands safe at all times. Don’t forget to wear protective gear; it can make a difference between life and death.
The DeWalt DWE7480 is a 10 in. compact job site table saw powered by a powerful 15 A motor that has top speeds of up to 4,800 RPM. When this power is paired with its 24 in. rip capacity and 47 degree bevel, this table saw is able to power through even the hardest woods with great accuracy, so you can use it for projects ranging from shelving to trim to hardwood flooring. And despite all its power, this table saw is a lightweight at only 48 lbs. No matter what woodworking project you have in front of you, this DeWalt table saw is able to power through it!
If you’re a home DIYer or pro working mainly from a shop, you may have a wide table or countertop big enough to use the saw without any accessory stand. We would caution against working on sawhorses, though, as they can be wobbly and unsafe. It’s far better to spend a few extra dollars on a sturdy stand than to take risks with a rickety, improvised setup.

Methods for tilting the blade to cut bevels vary among the saws. The Porter-Cable saw is the only one with a conventional handwheel bevel control mounted on the side of the saw. The crank gives you great control for setting an exact angle. To set the bevel on the Bosch, DeWalt and Rockwell saws, you simply release the bevel-lock lever and tilt the saw to the preferred angle. It’s easy to go quickly from a 90-degree to a 45-degree bevel with this method. The Ridgid, Craftsman and Ryobi saws have a rack-and-pinion setup. These saws utilize the front crank for setting the bevel.

Standard table saws are also called contractor table saws, even if they're really intended for the home do-it-yourselfer. These table saws have open, fixed legs, and they take up more space than a portable or benchtop table saw. They're also heavier – weighing as much as 200 to 300 pounds. On the plus side, their tables are often larger, making it easier to cut 4 by 8-foot panels of plywood or sheetrock. Prices for contractor saws range from around $600 to nearly $2,000.


We recommend something with this technology for new woodworkers, instructors, or folks who work in a busy shop with lots of movement around them. They’re also a safe bet for buyers who simply like to take as many precautions as possible. The only downside to these systems is the price. You’ll find them on machines closer to the $3,000 mark, as a rule.
It’s highly portable. Even though the whole body feels sturdier than the Dewalt’s, it’s still relatively light, at just about 60 pounds. There are handles in both the top and bottom edges of the machine, for easy lifting, and once you’ve got the saw fixed to the base, you won’t have to lift it on your own except for when you’re loading it in the back of the truck/van.

I’m no stranger to Bosch’s 4100-09 saw with Gravity-Rise™ stand. I’ve used one several times to build projects for this magazine, including the Serving Tray Cart that appeared in the June issue. So, I was not surprised when it tested impressively here. Rip cuts were on the mark, thanks to a rugged, beefy fence that stayed parallel to the blade each time I reset it. A flip of a red lever underneath unlocks the rails so they slide out and extend ripping capacity up to 25″.

We had a number of these saws – and I bought one for my own use (travelling to my kids houses and for garage use) since my old Unisaw with sliding table isn’t exactly portable. My take on the blade – is that the old 40T one (Bosch CBT1040A) was not worth anything much – so the change to a 24T blade can’t hurt (zero time anything is still zero). They generally bundle saws with cheap blades to keep the overall price down – but when I was buying in many multiples – I would have been happy for $10 off each if I had a “no-blade” option.
Look for a blade guard and splitter assembly. The guard will keep your fingers and sleeves away from the blade, while the splitter will keep your wood from re-binding together and jamming the blade, or causing kickback. Kickback is one of the biggest hazards of using a table saw, aside from coming in contact with the blade. Make sure you have either a splitter assembly or a riving knife on any cabinet saw you use.
The Grizzly G0690 is a very unique and powerful table saw and each part of it says performance and quality. With a 3 HP, 220V, 3-phase Leeson motor, heavy cast iron trunnions, wings and table to its triple belt drive system, this model should definitely last you for a lifetime. It’s not only its impressive build quality that’s going to strike you about it, but also its other features that include a four inch dust collection port, a T-slot miter gauge, a magnetic switch, but also heavy cat hand-wheels, riving knife and camlock T-fence. If you’re a professional who’s been using cabinet tablet saws for a quite a while, you’ll immediately appreciate the quality of the Grizzly G0690.

You can store and transport the Bosch upright or on either of its sides. In between our tests, we found that the saw neatly stored away on its side on a workbench shelf. On the other hand, the DeWalt can only be stored or transported in its upright position. While it may possible to rest the saw briefly on one of its sides, there is the potential to damage the power cord, plug, or the ends of the telescoping fence rails.


Optional portable table saw stands are available for both saws. (Bosch's stand is called the GTA500; DeWalt's is the DW7450.) The Bosch features tool-less connection (after initial assembly), while the DeWalt requires the attachment and tightening of four bolts through the DW745's bottom roll cage— though it's nothing a few after-market knobs couldn't fix.
The first is how easy the switch is to operate. Oftentimes, you will approach your table saw with your hands full especially when we are talking about sheet goods. And sometimes you’ll be making cuts that require both hands to be occupied. Now if something goes wrong or you need to turn the saw off for any reason, you need to be able to do so and the quicker the better.
A table saw can be classified in many ways, and I’ve come across terms like contractor, folding, featherboard, hobby, induction, sliding and zero clearance. However, I will conform to the most basic and clear classification and range the tables accordingly. That means I’ll order them by benchtop table saws, jobsite table saws, cabinet saws and hybrid table saws.
The quality of cut is as good as I can get with a cabinet saw, with one key exception: It takes more time to get it set up just right. There isn’t as much lead up before the blade, so getting the wood to track true is harder with less fence. I kind of wish they had backed the blade up an inch or two assuming they couldn’t make the saw a bit deeper.

While other cabinet table saws may not offer you a clear cut every single time, that’s not the case with the SawStop ICS51230-52. This model features industrial fence system which ensures that every time you cut something, the cut is going to be very accurate and perfectly straight. One last thing to keep in mind is that the unit includes a standard base, while the mobile base and jobsite cart are sold separately. 
×