Dust collection can seem like an afterthought for jobsite table saws. The fact that you’re outside, often on an unoccupied site, negates the need to collect your dust. But breathing that stuff doesn’t do your lungs any favors. That’s why dust collection is so important. Of course, if you’re working inside or in an occupied structure, collecting all that dust will make the cleanup part of your day easier to deal with. Since we’re not talking about concrete dust regulations, even a standard shop vac will be a good bet to help contain the mess.
The quality of cut is as good as I can get with a cabinet saw, with one key exception: It takes more time to get it set up just right. There isn’t as much lead up before the blade, so getting the wood to track true is harder with less fence. I kind of wish they had backed the blade up an inch or two assuming they couldn’t make the saw a bit deeper.
When I moved to a new home my shop area was radically downsized to half of a two car garage. In my former shop I had a 10" contractor's table saw for over 30 years. I really loved that saw but knew I was going to have to get a smaller saw. I reluctantly purchased the Bosch 4100-09 10" jobsite saw not expecting much. Wow was I wrong. I've had the saw for about a year and a half and use it daily to build medium to smaller sized projects ( boxes, trays, hanging cabinets, end tables). Right out of the box the saw performed well, I had my doubts about doing fine cabinet and furniture work but it is up to the task. I added the TS1002 outside table which is a necessity for larger boards. I also purchased the TS 1007 dado insert. The saw accommodates my freud 8" dado stack up to 1/2" which is sufficient for me. I use only thin kerf blades with a stabilizer and I've had no trouble ripping up to 1 1/2" hardwood. I do have to take it slower than on my contractor's saw but I
Because we’re passionate woodworkers who care deeply about the quality of the tools we work with, we have a tendency to recommend that even the most budget-conscious buyer spend a little more to get something high-quality. However, we know that some DIYers might have the ambition to take their woodworking to the next level with a table saw, but might not necessarily have the funds.
The Dewalt DWE7491is the clear choice for the full-time woodworking professional. It provides the widest rip capacity by far, it’s the fastest worker, and it has the best dust collection. The fence is a thing of beauty, and the secondary inner fence is a smart feature for smaller cuts. We think it’s worthy of any full-time woodworker, or DIYer with plenty of shop space and spending money.
The latest advance in table saw safety is a feature that stops the spinning blade when it senses the presence of tissue, such as a finger or forearm. A company called SawStop was the first to offer this technology, and currently, it holds the exclusive right to sell saws with this feature in the United States. (Bosch introduced a portable table saw with blade-stopping technology in 2016, but was forced to take it off the market after a successful patent-infringement suit by SawStop.) In 2017, the CPSC proposed a new rule to make SawStop's technology mandatory on all table saws, but that rule is still under review. See the Buying Guide for more information.
One of the biggest issues and potential hazards when working with table saws is kickback. Table saw kickback occurs when wood is ejected from the saw at extremely high speed. You can imagine the sort of injuries this can cause. Table splitters are effectively small vertical bits of metal or sometimes plastic that are designed to stop the wood flying back if there is a kickback. Attached to the splitter are anti kickback pawls either side, they look like table saw blades themselves but they are in fact there to grip the wood at stick into it in case of kickback.
The throat plate is the removable piece surrounding the blade that sits flush with the table. Removing it gives you the ability to access the blade for removal or riving knife adjustments. The narrower the blade clearance the better for two reasons. First, it helps keep material from falling into the blade area or lodging between the blade and throat plate. Second, it gives you material support very close to the cut to help reduce tearout as the blade exits the cut.
However, it provides a bit less room to work, and it’s not as easy for newer woodworkers to use. The power/stop switch is rather small, and this one doesn’t have a digital angle display like the Grizzly. We highly recommend it to working professionals who need maximum cutting capacity in a minimal footprint. It’s also a good choice for ambitious DIYers who are short on space, but really know their way around a table saw.
Though this table saw will arrive in multiple pieces, Jet includes all the instructions and help that you need to assemble the cabinet and all other parts. The cabinet itself has an enclosed design that keeps the motor and all other components safe from the dust in your workshop and any debris flying around. You also get four legs that attach to the base of the cabinet, which lifts the saw higher in the air to reduce back pain caused by bending over the table.
Which leads to a problem. A standard blade should not have that kind of space around it. Fortunately, Bosch sell very inexpensive throat plate blanks that can become zero clearance inserts. I have one for each of my three main blades and a fourth unused one that I put aside just in case. While I can make my own, it just isn’t worth the hassle as these are pretty affordable.
Bosch 10” table saw has it all in terms of precision and accuracy. It has a riving knife system for high material controls and visibility in cutting. The blade is designed with anti-kickback pawls to ensure once you start cutting, you will get accurate results to the end. The entire unit is designed with heavy-duty material for durability. The square lock rip fence has adjustable style to guarantee continued accuracy and precision in all your work. Additionally, the table saw has an easy to transport design with additional tabletops handles for portability. You can also regulate the cutting speed of the table saw to the place you are comfortable.
Editor’s Note: If you’re using the Bosch REAXX saw without dust collection, you’re going to want to partially open up the clasp located on the bottom of the saw. This allows the sawdust to exit the blade chamber through a half-inch gap. Failure to do this will clog the output port in a very short amount of time. When you use a dust extractor you can keep this chamber fully closed.
This woodworking website has tons of information about how to use a table saw: choosing blades, cutting joints, safety features, and more. However, we found only five actual product reviews, none more recent than 2013. Although these individual reviews are hands-on, they don't put saws through any specific, detailed tests. There's also no direct comparison between saws and no formal rating system.
Move the wood to and then "through" the spinning saw blade slowly and steadily. It's alright to use your hands while you're still at least a foot or so from the blade, but once the end of the board or sheet nears the blade, you should use a pushing stick to keep the wood moving and to keep your fingers away from the blade. Even an experienced carpenter can have a lapse in concentration or a slip that can lead to serious injury.
The DEWALT DW745 and the Bosch 4100 both have 15 amp motors, so power shouldn’t be a problem with either of these job site table saws. The DEWALT has a high torque motor that is capable of delivering a no-load speed of up to 3,850 rpm. The Bosch 15 amps and a no-load speed of up to 3,650 rpm. The difference between the two is not something that would be noticeable without sophisticated equipment, and will not affect performance in any significant manner. The noticeable difference between the two is that the Bosch 4100 comes equipped with a soft start motor that is lacking on the DEWALT DW745. This will cause a noticeable load on your power source, and may affect other tools and lighting attached to the same source during startup.
The integrated blade carries an electrical signal. Once it comes in contact with human skin, the signal changes because of the skin’s conductivity and the blade immediately stop. Although some people don’t like the process of resetting the blade, it’s quite easy, and it takes only a couple of minutes. If you think about it, it’s better to hassle by resetting the blade for five or six minutes instead of losing a few fingers.
Safety and precision are usually at a high level. Some models even offer a sliding table as an option to mitigate cross-cutting. Needless to say, hobbyists love the sliding feature because it saves a lot of time and most importantly – nerves. As far as the driving mechanism goes, there are three possible options – single V-belt, serpentine belt, and a multiple V-belts.
Delta 36-L352 10 in. contractor table saw is a heavy duty table saw. This big guy is no joke! Its 15 A, 3 HP motor is not only powerful but smooth. This Delta table saw also has a HUGE rip capacity of 50-52 in. and a 82 in. table, so there won’t be much this table saw can’t handle. Its integrated BIESEMEYER fence system, precision bevel gauge, and bevel dial work together to help you get highly accurate cuts down to the nearest 1/4 degree and 1/64 in. Now that’s accurate! Other notable features are its bi-level dust extraction system which helps you keep your work space clean, large blade opening, and SURE-LOCK dual front cranks for easy access. This table saw is ideal for the pros.
The Powermatic 1792001K PM2000 is an award winning cabinet table saw that features a 1-phase, 3 HP motor with rout-R lift and Accu-fence system which set a new standard for innovation through thanks to the saw’s large body design and an incredible range of patented features. The 1792001K PM2000 is the result of years of work and research and hundreds of interviews with woodworkers that offered input which was eventually implemented in the saw. The performance, reliably and safety of this saw are so great, that they actually set a new standard by which all other cabinet saws are judged.
rarely have to work with stock that thick. I mostly prefer to do this on my bandsaw any way. The 2" dust port allows me to hook up the shop vac and it does a decent job of getting most of the dust. The saw doesn't have much room in front of the blade so it was impossible to use my shop made cutoff sled. I solved this problem by making my own removable infeed extension table. Now I can use the 22" cutoff sled. After a year and a half the saw is still in adjustment and runs true. The saw stays in my shop and doesn't get bounce around on the back of a pickup truck. Based on my experience I highly recommend this saw if you have a small shop and don't plan on building large pieces
Located right next to the hand wheel on the front is a panel that features both a power button and a stop switch. The power button helps the motor come to life quickly without requiring that it heat up first, and you can press down on this button to turn the saw off at the end of the day. The emergency stop switch helps you stop the blade in the middle of a project to prevent accidents caused by clothing or skin coming into contact with the blade.
It’s heavy-duty. Like all great cabinet saws, the Grizzly is built from parts that can last a lifetime or more. It has a cast-iron table, that’s precision-ground to be exactly level, with no warps or imperfections. The trunnion supports holding up the motor are also solid cast iron, which means that they don’t translate much vibration to the work surface at all. The paint on the cabinet and extension frames is powder-coated, and the miter gauge and riving knife are solid steel. Both extension table surfaces are made with a coated, engineered composite, which stands up well against dings or scuffs.
It has a lot of the same features we love on the Grizzly. The Jet has a cast iron worktop, a full cabinet enclosure, and a fence on rolling tracks along the edge of the table. It has a belt-driven 3HP motor, an electric brake with a magnetic switch, and precision-machined parts for exact cuts. There’s also an included miter gauge with a follow pin that runs in the T-slot on the saw’s worktop. All in all, it’s another complete package that ticks all our key boxes!
First off, consider how often you’ll put your table saw to use. If you work in the fields of contracting or carpentry, there’s a chance you’ll be using your new machine pretty often — so you may as well invest in a more expensive, heavy-duty table saw that’s sure to last longer than the average model. On the other hand, hobbyists and weekend woodworkers won’t need a pricey piece of machinery — a more compact and inexpensive model should do just fine, especially if you’re only working on smaller projects like birdhouses and DIY wooden models.
Though you’ll still want to wear safety gear when using this table saw, it has safety features that will keep you safe too. One of those features is an emergency stop. One touch of the bright green power button brings the motor to life, but when you lift up on the emergency stop that surrounds the power button, you can stop the motor in its tracks. This button has a convenient design that lets you hit and lift it with your leg or knee too.
Measuring 30.31" x 17.32" x 41.81", this powerhouse boasts a heavy duty 10" blade that can cut up to 4" x 4" of material in a single pass. For the handyman who likes to keep all of his tools within arm’s length, RIDGID’s table saw comes with convenient onboard storage so swapping out blades or accessing your tools is just a short reach away. Buyers are crazy for this table saw, and they report that it easily fits into the corner of their garages. Plus, quick and easy assembly means you can get to work straight out the gate.