Among the features that set this table saw apart from other competitors is the SquareLock Rip Fence. It is fabricated out of machined aluminum, slides up and down the rail without a hitch, and fixing positions couldn’t be easier. It’s probably the best fence I’ve seen in portable table saws, it feels very solid and is incredibly accurate and precise.

TBB measured the accuracy of the factory-set 90 degree stop by using a Wixey WR365 digital inclinometer. This device has an accuracy of 0.1 degree. We placed the Wixey gauge on the table and calibrated the inclinometer to the table by zeroing out the gauge. After that calibration, the measurements give a result that is relative to the saw table. We moved the blade to an approximate position of 70 degrees off vertical. TBB attached the gauge to the blade and used the saw mechanism to adjust the blade incline to the point at which the blade or trunnion hit the factory-set 90 degree vertical stop and recorded the measurement. TBB ran the test twice to ensure the repeatability of the measurement. In every case, the result came out to within 0.1 degree of the prior test.


Editor and "serious woodworker" Chris Marshall tests five "premium" portable table saws. After equipping each saw with a new Freud thin-kerf blade, he uses them to rip lengths of medium-density fiberboard (MDF) and yellow pine, as well as making long dado cuts in MDF. Marshall considers the saws' stability, cutting accuracy, efficiency, dust collection, and general ease of use to choose his top picks. Unfortunately, two of his three favorites are discontinued.
As you would expect, the most expensive saws made slightly smoother cuts. But the difference was negligible. The only saw that struggled to make smooth cuts in the super-thick oak was the Ryobi. In more common situations, like cutting 3/4-in.-thick material, Ryobi’s cut quality was fine. We found the blades included with all the saws to be adequate for most ripping tasks. But if you want cuts smooth enough for glue joints, you’ll have to invest in a better blade.
When I switched blades, I did find the locking lever for the riving knife very stiff … not sure why. It raises to release the riving knife and pushes down to lock it. I resorted to gripping the lever with a pliers to manipulate it, after nicking some skin on the blade teeth. But, on the softer side, RIDGID provides a nice complement of overmolds on the miter gauge handle and blade height handwheel knob.
This Portable Table saw includes an industry standard This Portable Table saw includes an industry standard tool-free split guard design that allows a true rise-and fall riving knife by using a lever on the inside the throat plate. It has a Tool-less assembly for the riving knife and anti-kickback pawls. It's perfect for mobile contractors and the Do-It-Yourself ...  More + Product Details Close
There’s also a secondary flip-down fence which allows you to make narrower rips. We love this feature, which should really become industry standard in the near future. It helps you make smaller cuts without needing to have your fingers close to the blade. Reviewers loved it, and said they found themselves using the feature much more frequently than they’d anticipated.
To get the feel of the cut, we used a two man team to feed from one end of the saw and catch on the other. This helped us reduce the friction that comes from one person trying to hold a board flush against the fence while also keeping downward pressure to keep it level on the table. There was definitely some hesitation at the beginning of each cut that was alleviated once the board was received by the second man on the other side. It was during this middle section that the table/fence friction was at its lowest point and we made our determinations about each saw’s power and cutting speed.
DeWALT DWE7480 is an excellent table saw, especially if you consider its price. It’s a step up from the highly popular DW745 and slightly more expensive, but I think the larger rip capacity and higher RPM are well worth the extra money. The DWE7480 is still in the lower price region though, and unlike the DW745 you can also get this one with a stand: the DWE7480XA!
The simplest way to find out what size your table saw needs or indeed if you’re buying a special size is to consult the table saw user Manuel. I would make sure you do this as often there are many things in modern tables saws that could affect the blade size and type. This is because modern saws have many different amazing and varied features, things size blade guards, special safety mechanisms and arbor sizes etc. With the We recommend you spend some time reading your manual in detail to avoid possible issues

The only (somewhat) recent review of table saws at Wood Magazine pits nine 3-HP cabinet saws against various sizes of wood and plywood, fed both by hand and with a power feeder. The short version of the review available on the website names the top picks and notes areas in which all nine saws performed adequately. For full details, however, you need to check out the printed magazine.
With this saw, it was a very easy thing to plug it on and get started. The included cord is a reasonable length, but you’ll still need an extension cord unless you happen to be right next to an outlet in your workshop. Raising and lowering the blade is a smooth process and we found the mechanism to be nice and stiff, so you can be very precise with your cut depth. Only time will reveal whether or not this stays tight over the long haul, but it seems to be well-made. Mounting the accessories, like the smart guard system is quick. You just raise the riving knife using the release lever. The riving knife locks into a lower and upper position through the use of two sets of pins. In the upper position it is ready to accept the barrier guard, which you can remove from below the saw. It attaches easily with a lever lock and the anti-kickback device can then be placed on the back of the riving knife such that the teeth are set to grab any wood brought forward by the blade. The physical nature of the barrier guard assembly precludes you from placing your fingers anywhere near the cutting surface of the blade. We (and Bosch) recommend keeping this guard on the saw anytime you are doing “through” cuts. All-in-all, the table saw’s included safety features are more than adequate to keep you from encountering any unfortunate accidents. Removing them, or using the tool improperly, however, will considerably raise your level of risk.
One term you may hear when reading about table saw accuracy is blade runout. Runout is a term that describes whether or how much the outside edge of a saw blade wobbles while being held by the motor shaft. Sometimes, operators measure runout by using a saw blade. In that case, the very use of a saw blade presumes that the specific blade is perfect or nearly perfect in its flatness. Using a saw blade that has any warping will not give a clear indication of blade runout.
When using the side extension, a tape moves along so you won’t have to remember what measurement to lock the fence on or read a double marked measurement guide. It’s an innovation we like, but there are questions as to the long term durability of the tape itself. Like Ryobi, Ridgid uses a magnetic throat plate to secure it while leaving access simple.
Every woodworker knows the plague of working in a dusty environment. The SawStop has a fantastic dust collection system so you can enjoy your cutting without your eyes being strained. Almost all of the dust is wicked away both above and below the table. Up above, the blade does all the legwork and there’s a neatly designed shroud which pulls all this dust away from the blade. The 4-inch port means you can slip your shop vac on with no issues.        
Jet has a strong reputation for providing customers with durable power tools that operate just like professional models but cost less, and that is definitely true of this 10-inch table saw that comes with a riving knife. You’ll like the basic design of this model, which has an intuitive design that allows you to set it up and start cutting faster. It features both a solid cabinet as well as an extension table that stretches out from one end.
Delta has also improved the tabletop geometry on this model which means that you’re going to get more surface area stabilization. The base is also made of durable cast iron and since it offers easy access to the off/on switch, using the Delta UNISAW is a breeze. Other user friendly features include the convenient dust extraction system, large blade opening for easily changing the blade and fine-tuning the riving knife, smart storage for simple organization and fast access.
Likes: Cuts extremely well and has excellent stability. Its blade guard and riving-knife assembly are locked and unlocked by a lever located conveniently along the table's left edge. A simple, separate shark-fin riving knife can be used when the guard is too big for narrow rip cuts. We appreciate the antiglare surface on the tape ruler that measures the distance from the blade to the fence.

Cabinet table saws are the best choice for full-time professional woodworkers with a dedicated workshop. If you have a spacious shop, these are some of the most efficient, versatile cutting tools you can buy, especially for larger stock. With 3+ HP motors, they’re by far the most powerful machines you can get your hands on. Plus, their heavy, machined build quality gives you a precision and smoothness in your work that really compliments the professional. They have the most effective dust collection systems of any table saw, and durability that can last more than a lifetime.
SawStop has an excellent stand and they’ve cleverly hidden the tool/miter/riving knife storage box under the side extension. Move the table extension and the box presents itself. Like DeWalt, two riving knives come with the saw—one with safety guards and one without. This keeps you from wondering how the pawls and guard go on the riving knife. Blade height fully adjusts with only one turn of the wheel. Not everyone was on board with this, citing less accuracy for dado and rabbet cuts. In the end, we showed we could be as accurate on the height as any of the other saws, so it’s a win.
A table saw can be classified in many ways, and I’ve come across terms like contractor, folding, featherboard, hobby, induction, sliding and zero clearance. However, I will conform to the most basic and clear classification and range the tables accordingly. That means I’ll order them by benchtop table saws, jobsite table saws, cabinet saws and hybrid table saws.
While you may be tempted to skip straight to the reviews, they are a bit on the technical side and contain plenty of terms you might not be familiar with just yet. My suggestion would be to start by reading the informational articles which will provide you with a decent amount of knowledge on table saws. After that, I sincerely doubt you would be caught off-guard while reading anything in the review section.

Blade guards are an important safety device and should never be removed from the saw. You want to find one that rises up parallel to the table so it is always on top of the material you are working with. The purpose of this blade guard is to protect you from the spinning blade. While some woodworkers find them annoying, the safety they provide is well worth the inconvenience.
The Grizzly G0690 is a very unique and powerful table saw and each part of it says performance and quality. With a 3 HP, 220V, 3-phase Leeson motor, heavy cast iron trunnions, wings and table to its triple belt drive system, this model should definitely last you for a lifetime. It’s not only its impressive build quality that’s going to strike you about it, but also its other features that include a four inch dust collection port, a T-slot miter gauge, a magnetic switch, but also heavy cat hand-wheels, riving knife and camlock T-fence. If you’re a professional who’s been using cabinet tablet saws for a quite a while, you’ll immediately appreciate the quality of the Grizzly G0690.

On the downside, these units are by far the heaviest type of saw, and they’re the most expensive by a long shot. Their cast iron worktops and steel cabinets makes them more of a permanent fixture than nearly any other tool. To move them around your shop, you’ll need an expensive, heavy-duty wheeled base, which can cost even more money up front. They’re best for people who will keep them in one place, and use them on a regular basis.
The Bosch 4100-10 10 In. Worksite Table Saw with Gravity-Rise Wheeled Stand is a portable table saw with outstanding capacity and capability. The powerful 15-Amp saw delivers 4.0 max HP, with a large machined aluminum tabletop and a wide 25 In. ripping capacity. The Gravity-Rise Stand provides easy setup and take down. The SquareLock rip fence is engineered for trueness. The 4100 table saw also comes equipped with advanced electronics, such as soft start, constant response circuitry and overload protection.
Before we get into some of the top features, we want to take a look at the design of this cabinet. As it uses an enclosed cabinet, you’ll find that the motor lasts longer because it doesn’t wear down due to constant exposure to dust. This cabinet also features convenient hand wheels on the front and sides that help you make quick adjustments before cutting or as you work.

Though this table saw will arrive in multiple pieces, Jet includes all the instructions and help that you need to assemble the cabinet and all other parts. The cabinet itself has an enclosed design that keeps the motor and all other components safe from the dust in your workshop and any debris flying around. You also get four legs that attach to the base of the cabinet, which lifts the saw higher in the air to reduce back pain caused by bending over the table.
Three professional carpenters test ten portable table saws, including two now discontinued. They outfit them all with Diablo 40-tooth general-purpose blades and test them on both 3/4-inch plywood and pressure-treated 2x pine. Each saw earns points for safety features, fence quality, stability, weight, stand design, ease of adjustment, cutting power, and dust collection. Totaling up these scores determines the saws' overall ranking, as well as their "class ranking" against comparably priced brands. Some additional single product reviews of table saws can be found elsewhere on the site as well.
We made a few test cuts with ¾-inch plywood just to get a feel of the motors we were working with. It became clear pretty quickly that not all 15 amp motors are equal. Once we knew what to expect, we moved to pressure treated 2x pine material in 7-1/2 foot lengths. Why 7-1/2? Our test material started at 15 feet and it seemed silly to have some at 8 feet and others at 6.
Table saws will use one of two different kinds of drive configurations; Direct-drive motors and Belt-drive motors. In a direct-drive motor, they will link directly to the blade itself and transfer all of the power of the motor to the blade. They tend to last longer than belt drive motors and there is no belt to replace or worry about getting worn out. Belt drive motors transfer power from the motor to the blade through a belt. In this type of configuration, the motor can be offset away from the sawdust which helps the motor last longer. In general, belt drive motors need more preventative maintenance than direct-drive motors do. If you have a belt drive motor, check the tension of your belts as well as checking them for wear periodically to ensure your continued safety.

The 708494K JPS-10TS from Jet Proshop is a high end cabinet table saw which delivers on all your expectations. Available in either a thirty inch or a fifty two inch rip capacity, this model is built from cast iron and is extremely rugged in order to withstand a lot of abuse and still deliver the excellent results you’re expecting from it. Regardless if you’re a professional or if this is the first cabinet table saw you’re planning to get, the 708494K JPS-10TS won’t disappoint. Its rugged build quality and ease of use are going to make it one of the best table saws currently available.


One thing you’ll love about the riving knife is that it allows for adjusting the table saw without using any special tools, for non-through and through cuts including, pictures frames, grooves for shelves, but also cheek cuts for furniture, rabbets and dadoes. There’s also the possibility to store different tools or anything else you may find under the tablet board and given the fact it’s expandable and convenient, it’s going to make using the Delta 36-L552 an even more amazing experience. For dust collection, the table saw comes with a bi-level dust extraction system which offers superior dust collection capabilities.
Dewalt has refined the DW745's design, most notably improving the blade guard and safety measures. What stands out about the DW745 is its rack-and-pinion rip fence that moves along telescoping rails at the front and rear of the table. This means that once the fence is set square, it should stay square. However, the DeWalt's maximum width for a rip cut is 16 inches, compared to 18 inches for the Bosch. But most users will make large rip cuts with a circular saw, so the 2-inch difference in capacity isn't a big deal.
A splitter is a piece of metal that keeps the blade from binding in whatever material you are cutting if the saw kerf starts to close up. The splitter is vertical and sits directly behind the blade. This plays a big part in preventing kickback and should be mounted on the motor assembly so it rises and falls with the saw blades movements. You can also get splitters that can be adjusted to fit the width of the kerf.
To learn about how table saws perform in real people's homes, we consulted owner-written reviews at retail sites like Amazon, Home Depot, Lowe's, and Sears. User reviewers don't have the breadth of experience that many experts enjoy, but they can provide keen insights on the model they bought, including things that might not crop up in the relatively short time professional reviewers have to spend with a given saw.
post-template-default,single,single-post,postid-5859,single-format-standard,mkd-core-1.0.2,ajax_fade,page_not_loaded,,table saw theme-child-ver-1.0.0,onyx-ver-1.4.1,vertical_menu_enabled, vertical_menu_left, vertical_menu_width_290,vertical_menu_background_opacity_over_slider vertical_menu_background_opacity_over_slider_on,smooth_scroll,side_menu_slide_from_right,wpb-js-composer js-comp-ver-4.7.4,vc_responsive
In our introduction and how-to sections, we’ve talked about some of the key reasons to buy a cabinet-style model. These are the most stable table saws you can find. They produce the smoothest, cleanest cuts. They’re also tools that are built to last a lifetime. We recommend them to any professional with the shop space to install one. They’re also the ultimate choice to ardent hobbyists with plenty of room to spare and an ample budget.
Finally, hybrid saws combine the lighter weight of the contractor saw with the more powerful motor and sturdier construction of the cabinet saw, at a price that’s easier for the occasional woodworker to stomach. They can run about $1,200 or so, and weigh in at under 300 pounds. Their motors are generally in the 1.5 to 1.75 HP range, and can be used with standard 110V outlets.

The GTS1031 is Bosch's newest table saw, designed for portability and intended to be light enough that you could carry it with one hand. Its rip fence is designed for quick and easy movement, and clamps into channels on opposite sides of the table to keep things consistently square without the need for frequent adjustment. Two notable advantages for the GTS1031: Its 5000 RPM max no-load speed compared to the 3850 RPM for the DeWalt, and the fact that you can use a 1/2-inch dado set with it (though it requires separate TS1013 dado throat insert).
What if a contractor uses their job site saw for high quality built-ins or high tolerance finished cuts? In that case, saw accuracy is critical for that work. In this use case, if the saw is immediately put into use, success depends upon the out-of-the-box accuracy from the manufacturer. The quality of the cuts and more importantly the potential safety of the operator is going to be a function of the as-shipped accuracy of the saw from the manufacturer.

If you are just learning how to sharpen your table saw, you may wonder how to know when to sharpen your saw using your best table saw grinder. You do not want to end up sharpening it too much because that will damage your cutters. It is dangerous to work with a saw that is not sharp enough. Dull cutters tend to catch in the materials and propel the bar in the operator’s direction.
×