On the other end of the handyman spectrum, you’ve got the seasoned professional with years of experience under his belt. We all know the type: he’s the guy that expects only the best, and DEWALT more than delivers with their patented DWE7491RS. This wood-slicing machine is the cream of the crop when it comes to cutting through even the toughest materials. The DWE7491RS measures 26¼" x 22", so it’s a relatively large apparatus — you’re going to want to make sure that you have plenty of space in your garage for this table saw.
Bosch’s REAXX and SawStop were neck and neck with near perfect cleanup at the collection point and only a slight amount of dust coming out toward the user. What did make it out was even less coarse than the other Pro level saws. Both saws have narrower throat openings for the blade that reduce the amount and size of material that can make it out. In the end, SawStop produced less top dust than Bosch did to earn the win.
I appreciate the helpful comparison of the best table saws. I’m fairly new to woodworking, and until recently I was using an old table saw that used to belong to my dad. Long story short, it’s no longer usable, and so I’m looking for a good table saw to buy that’s beginner-friendly. I have my eye on the DEWALT DW745 – evidently it’s really popular and does a great job. I’ve taken a look at some other sites for more ideas. Your guide here is great. What is your opinion on the DW745?
While I appreciate this review, that Kobalt job site saw is the absolute worst. Uncontrollable blade wobble, terrible fence, trundle bolts that are nearly impossible to get to without tacking the back panel off (of course that doesn’t matter when the blade won’t stay in alignment for more than a day), miter slots that aren’t parallel to each other and also taper toward the backside of the table, and a riving knife without adequate adjustments to align it with the blade. Do not buy that piece of garbage.
We were impressed with the Bosch Glide Miter Saw which was revealed in 2010 and revolutionized the depth required by a saw in close quarters. Building on their solution-based approach to products, the company has finally addressed the need for a truly portable full-power jobsite table saw. The Bosch GTS1031 table saw can be carried by its single handle, which is balanced in the middle, and all accessories are safely and securely stored on-board. This was demonstrated wonderfully by none other than Jason Feldner at the 2011 Bosch Media Event, who came running into the room with the Bosch GTS1031 table saw in one hand and a GTA500 stand in the other. Weighing in at a manageable 52 pounds, and this is one 15-amp jobsite table saw that does a great job of balancing portability and raw cutting power.

It’s expensive. This one will cost you over $3000. That’s no casual purchase, and the high price tag makes this cost-prohibitive for some buyers. However, you really can’t put a price on the peace of mind that comes with having a unit with this sort of safety system onboard. Our advice? If you can muster the cash, and will get your money’s worth out of the machine, it’s well-worth the price.
If the blade you purchase has a .092” kerf (i.e. Irwin Marathon 80T, FreudLU83R010) you will most likely have issues with binding on the back end of the cut. To be safe, find a blade that has a kerf of around .098” (i.e. Freud Avanti TK905 50T) and this should take care of the problem. You should also take note that every blade Bosch makes should also work with the Bosch 4100-09.
In order to measure the blade speed we used a digital laser non-contact tachometer. A piece of reflective tape was adhered to each saw blade just behind the carbide tooth, so that the tape would be just above the top of the wood cutting surface, allowing us to capture the blade speed during the cuts. We used a power-feeder to ensure that all the material was pushed through each saw at the same feed rate. In the photo above you can see our test set-up with the power feeder, a decibel meter to the left, the digital tachometer in the center, and the amp meter on the right. If you look really closely at the saw blade, the piece of reflective tape is to the left side of the blade near the power feeder.
Which leads to a problem. A standard blade should not have that kind of space around it. Fortunately, Bosch sell very inexpensive throat plate blanks that can become zero clearance inserts. I have one for each of my three main blades and a fourth unused one that I put aside just in case. While I can make my own, it just isn’t worth the hassle as these are pretty affordable.
In our introduction and how-to sections, we’ve talked about some of the key reasons to buy a cabinet-style model. These are the most stable table saws you can find. They produce the smoothest, cleanest cuts. They’re also tools that are built to last a lifetime. We recommend them to any professional with the shop space to install one. They’re also the ultimate choice to ardent hobbyists with plenty of room to spare and an ample budget.

I can’t tell you how many times we’ve pulled out other jobsite saws only to have accessories fall off, or require off-tool storage. Bosch designed the GTS1031, however, to securely hold all of its accessories, even including the arbor wrenches (both of them) and an allen wrench for adjusting the riving knife and dust ejection points among other things. Our favorite was the rip fence, which simply flipped upside down and stored underneath the table – clever! About the most difficult adjustment was the riving knife, which is a tool-less maneuver, but one which requires you to stick your hand way into the blade cavity to reach the release lever. When making any adjustments to the blade, it goes without saying (but we’ll say it anyway) to disconnect power to the saw as a precaution.
Bosch engineers deserve kudos for the Gravity-Rise stand, and it’s a design some other manufacturers should emulate. Twist one lever, and the sturdy, steel frame folds up or down fluidly to convert from sawing to transport or storage. Eight-inch wheels and lugged rubber tires make this base easy to steer overland or pull up steps. Plus, the base’s stance is wide, giving it sure footing if you are pushing long planks or heavy sheet goods through. It will not tip. But, the stand when erected sets the saw’s tabletop quite high, at 38-1⁄2″. Shorter users may find this to be a bit too tall for comfort.
​The saw does not easily detach from the stand. Sometimes it’s beneficial to set the saw up as a bench-top saw, but the DeWALT 7491RS doesn’t come with quick release levers to accomplish this easily. In this case, you would have to use a drill to remove four screws to detach it from the stand. I wouldn’t recommend doing this unless you have to because over time the screw holes will strip.
The larger the motor, the higher the voltage as well, usually 240V. In some cases, you may be lucky and have a garage or workshop that’s wired for 240V, so that is why it’s very important that you check this prior to getting the table saw. In terms of the material thickness it can handle, it’s a minimum of three inches. One thing to bear in mind is that safety is an essential consideration with these saws and that’s because the powerful motors are prone to higher kickback.
The Grizzly G0690 is a very unique and powerful table saw and each part of it says performance and quality. With a 3 HP, 220V, 3-phase Leeson motor, heavy cast iron trunnions, wings and table to its triple belt drive system, this model should definitely last you for a lifetime. It’s not only its impressive build quality that’s going to strike you about it, but also its other features that include a four inch dust collection port, a T-slot miter gauge, a magnetic switch, but also heavy cat hand-wheels, riving knife and camlock T-fence. If you’re a professional who’s been using cabinet tablet saws for a quite a while, you’ll immediately appreciate the quality of the Grizzly G0690.
The Bosch 4100-09 10 In. Worksite Table Saw with Gravity-Rise Wheeled Stand delivers both professional rip capacity and outstanding portability for a tool that can get the job done, wherever it is. The powerful 15-Amp saw delivers 4.0 max HP for outstanding productivity. It also incorporates soft-start circuitry for smooth but quick ramp-up to the operating speed to manage the intensity of motor start-up and minimize the possibility of tripping a circuit breaker.. It includes Constant Response circuitry to help maintain speed under load, and overload protection. The Square Lock rip fence is engineered for maximum trueness and great ease-of-use, with the fence able to easily glide along the rail for one-handed operation. The lighter GTA47W Gravity-Rise Wheeled Stand has 8 In. treaded rubber-composite tires and a single-action design for easy set-up and transport. It is jobsite-ready with heavy-duty construction. The Smart Guard System is the first modular table saw blade guard, featuring a three-position adjustable riving knife, anti-kickback pawls and non-obstructed-view barrier guard assembly. The table saw provides a 29 In. x 21-1/2 In. square tabletop with a 25 In. rip capacity for ripping 4 Ft. wide sheets goods in half.
SawStop was second, also with features no other saw had. The blade height adjustment wheel covers the entire range with one full turn of the wheel. There was some discussion about micro adjustments being more precise for dado and rabbet cuts, but in practice, we found we could easily get to a specific height without trouble. SawStop also moves away from the bevel lock lever and instead integrates it into the height wheel. By pulling the lock toward you, it is released and easily moved to your desired angle. Let go of the wheel and it’s locked back in place without having to hold it and use a second hand to work the lever.
It has a machined aluminum table which is extremely precise. We like the Dewalt’s cast metal table for the price, but the company don’t list the material, and we suspect it’s not nearly as rugged as aluminum. The Bosch’s table is much better. It’s rugged, sturdy, and more consistently even than the Dewalt. The table makes this one a smarter choice for fine woodworkers or pros who need superior alignment.

Move the wood to and then "through" the spinning saw blade slowly and steadily. It's alright to use your hands while you're still at least a foot or so from the blade, but once the end of the board or sheet nears the blade, you should use a pushing stick to keep the wood moving and to keep your fingers away from the blade. Even an experienced carpenter can have a lapse in concentration or a slip that can lead to serious injury.

For benchtop and jobsite saws with direct drive motors, the motor RPM is the blade RPM. If you’re considering a contractor or cabinet saw, it’s a different story. In any event, Pro table saw RPMs generally range from 4000 – 5000. Don’t let numbers on the lower side dissuade you. There’s a limit to how much power you can draw and each manufacturer has to decide how they’ll channel it between blade speed and torque. So higher isn’t necessarily better.


Robert Bosch Tool Corporation is aware of questions raised about the power of its REAXX™ Jobsite Table Saw. We are taking this feedback seriously and we’re working with product and engineering teams to answer these questions. Flesh-detecting Bosch Active Response Technology™, which comes on board every REAXX Job Site Table Saw, is unrelated to the questions raised about the saw. The REAXX table saw remains one of the safest and most-advanced table saws available today. 
It has a smart fence design that allows for a wide rip capacity in a small package. The Dewalt’s rails telescope, which allows them to extend further than the competition without adding to the machine’s packable footprint. That means you can make rips at up to 20 inches without needing any extensions or other accessories. The rack and pinion system allows you to set a precise fence setting without wobble, even on a flexible rail. It locks at both the front and back, to make absolutely sure you’re getting an accurate rip every time.
One of the principal causes of table saw accidents is kickback. This process happens when a piece of wood is ejected at great speed in the direction of the user. Binding between the blade and fence, the wood then gets trapped in the teeth and spat out. A splitter is a vertical blade that holds the kerf open to minimize the chance of kickback. 2 pawls are attached for this purpose.
Sadly, you will have to sacrifice in a few key departments for all that portability and convenience. Portable table saws are the worst choice for cutting larger stock, especially if you don’t have an extension table to add on. They’re also the least powerful sort of table saw, so you shouldn’t plan to cut thick stock or hardwoods on them regularly. Thanks to their light build, portable units are the loudest of the bunch, and their dust collection is usually less than impressive. However, if you’re moving around a lot and need to do rips in the smallest possible space, these are your best friends.
If you’re a home DIYer, dust collection shouldn’t be a big worry. You can always hook the saw up to your shop vac, but if you’re only working with it occasionally, you’ll be fine to simply get your sawing done, and clear the exhaust port afterward. However, if you’re working on a professional jobsite, you should plan to collect at least most of the dust from your portable table saw via a vacuum system.
The latest advance in table saw safety is a feature that stops the spinning blade when it senses the presence of tissue, such as a finger or forearm. A company called SawStop was the first to offer this technology, and currently, it holds the exclusive right to sell saws with this feature in the United States. (Bosch introduced a portable table saw with blade-stopping technology in 2016, but was forced to take it off the market after a successful patent-infringement suit by SawStop.) In 2017, the CPSC proposed a new rule to make SawStop's technology mandatory on all table saws, but that rule is still under review. See the Buying Guide for more information.
The integrated blade carries an electrical signal. Once it comes in contact with human skin, the signal changes because of the skin’s conductivity and the blade immediately stop. Although some people don’t like the process of resetting the blade, it’s quite easy, and it takes only a couple of minutes. If you think about it, it’s better to hassle by resetting the blade for five or six minutes instead of losing a few fingers.

It has the widest rip capacity of the three. This one can handle materials up to 32 1/2”, which makes it ideal for folks who work with sheet stock on the go–especially when you consider the extra 22” you’ll have to the left of the blade. That’s thanks to the same rack and pinion fence as the smaller Dewalt. It’s even better on a larger scale, where the differences between this design and the sliding rail style you find on Bosch become very apparent. Reviewers agreed that this one felt much sturdier, smoother, and locked more securely than other portable units.
It has the widest rip capacity of the three. This one can handle materials up to 32 1/2”, which makes it ideal for folks who work with sheet stock on the go–especially when you consider the extra 22” you’ll have to the left of the blade. That’s thanks to the same rack and pinion fence as the smaller Dewalt. It’s even better on a larger scale, where the differences between this design and the sliding rail style you find on Bosch become very apparent. Reviewers agreed that this one felt much sturdier, smoother, and locked more securely than other portable units.
IMPORTANT REVIEW UPDATE (10/4/2016): After doing some additional testing with pressure-treated lumber and heavier stock, we [initially] found some issues with the Bosch REAXX saw that we couldn’t explain—except to say that it didn’t have the power we expected for cutting through denser wood. The blade exhibited a significant drop in speed during many common ripping cuts, and it even stalled out entirely at other times. We contacted Bosch and worked directly with them to determine the nature of the issue (which appeared to have to do with the saw’s electronic speed control). Here is the initial statement from Bosch on the matter:
It’s sturdy. This unit also has a metal roll cage frame all around, which helps it handle the rough and tumble of travelling to worksites on a regular basis. It has a locking mechanism to help it stay securely on stands. We’re also super impressed by how well-made the adjustment knobs feel on this one. Buyers reported using this one for several years with no issues.
If you need a table saw that can travel, the Bosch 4100-09 consistently earns high marks. Reviewers praise its power, accuracy, easy setup, and easy blade changes. They also love the gravity-rise wheeled stand, which rolls smoothly and snaps open or folds flat in a single lever-activated motion. Finally, they appreciate the convenience of the blade guard system, complete with riving knife and anti-kickback pawls.
But, their price point reflects that. If you want the absolute best table saw money can buy then you can go pay $10,000 and it’s yours. We always accept a certain number of tradeoffs depending on what our budget allows So, if I am only doing a few DIY projects a year, I am not a carpenter by trade, and my budget is limited, the SKIL table saw may be right up my alley.
The cabinet also has a few other safety features that set it on a level above the Grizzly or Jet. There’s an extra-large, paddle-style power switch which you can easily press with a thigh as well as a hand. The guard works tightly against the blade, so that you have all the workspace you need without sacrificing safety. The riving knife prevents kickbacks, and the left-tilting bevel feature prevents binding.

This “review” is a giant nothingBurger. There is not one scrap of objective comparison between these saws. Because you sell them, they’re all great and will all zip right through “the hardest woods”. Bulll$hit. You did not test, compare, analyze, or use ANY of these saws. Re-hashinf manufacturer specs is a “Roundup” but it certainly is not a review. Typical sales pablum.

You’ll make most of your miter cuts on a miter saw. But when the material you’re cutting exceeds a miter saw’s cross-cutting capacity, you turn to your table saw miter gauge. These usually aren’t quite as precise, but some manufacturers put more thought and robustness into it than others. If you make a lot of long miter cuts, be sure to pay attention to this accessory.
It is not a cabinet saw, so judging it by those standards would be unfair. As a portable job site saw this is amazing. Loud and dusty, sure, but that is expected. Easy to use and store, yes. The fence is square to the blade, and is rock solid, as long as you make sure the nut at the back of the fence is set right. The fence is not quite square to the table top, and I can't tweak it, but for construction I wouldn't care. I do other fussier things on the saw, so I will shim out an auxiliary fence. I made a cross-cut sled, which I recommend, and get thin kerf blades. I got a rip, general, and fine finish blades, and I get great results.
This portable jobsite table saw head-to-head includes 8 saws from; Bosch, Delta, DEWALT, Hitachi, Makita, Ridgid, SawStop and Skilsaw. Originally, we had also to include Ryobi as a budget friendly option for DIY’ers or guys just starting in the trades. However, we were not able to adapt that saw to our testing rigs so we pulled it from the testing (you may see some photos with the saw but again we’re not including it in the results).
If you are just learning how to sharpen your table saw, you may wonder how to know when to sharpen your saw using your best table saw grinder. You do not want to end up sharpening it too much because that will damage your cutters. It is dangerous to work with a saw that is not sharp enough. Dull cutters tend to catch in the materials and propel the bar in the operator’s direction.
×