While ordering generic no-name products might be fine for something like breakfast cereal, power tools are different. When you use power tools, your safety is at stake. If you pick up some cheapo piece of mass produced junk just because the price is less than a name brand, you might end up paying a lot higher price for it than you counted on. Why? Because generic power tools are not usually held to the quality control and accuracy as big box brands such as DEWALT and Bosch.
If you want to have a quick and accurate cut of wood, look no further than a table saw. When buying a table saw the main thing you put into consideration is its power. A good table saw should have enough power to cut through wet timber as well as hardwood. However, there are certain features which help in foreseeing the overall performance of a table saw.

Blade guards are an important safety device and should never be removed from the saw. You want to find one that rises up parallel to the table so it is always on top of the material you are working with. The purpose of this blade guard is to protect you from the spinning blade. While some woodworkers find them annoying, the safety they provide is well worth the inconvenience.
Ryobi’s RTS21G comes in as the only table saw in the group under $200. It’s lightweight, reasonably compact, and we got acceptable jobsite cuts with the upgraded Diablo blade. The throat plate uses magnets to hold it in place while leaving it easy to remove for blade access. Using a threaded rod to push the height adjustment up, you’ll notice it’s easier and smoother on the way down. The stand folds up and can be Velcro-strapped to the back, though it’s a bit wobbly compared to the others when ready for action.
The first measurements we looked at with the performance testing was blade speed cutting all three of the test materials. This tests gives us a relative comparison of how much blade speed reduction the motors have under different loading conditions. In our opinion this gives us an idea of how strong the motor/gear box combination is for each saw. For each test we also recorded the “no-load” speed to capture the relative drop in rpm in the blade speed while cutting wood. We used our as-measured no-load speeds instead of the published values from the manufacturers.
As for my blades, I replaced the blade that came with the saw right away. It is terrible and would have been better to be not included at all. I replaced it with a Freud industrial 24 tooth glue-line rip blade and a Freud Diablo 80 tooth plywood and crosscut blade (I find it easier to just buy new plywood blades since the glue does a number on them, not to mention the wear and tear caused by MDF). As an all-around blade, I keep a 50 tooth Tenryu Gold blade. It is quieter somehow, and does a cut almost as good as either the rip or crosscut blade. Great for making quick cuts without always changing blades. I will use it for most ripping, but will switch to the ripping blade when I have a lot of ripping to do, or will be going thicker than about 1.5” in hardwood.
Sometimes picking a “Best Bet” is a real tossup, but not this time. While Bosch’s 4100-09 doesn’t disappoint, and DeWALT has what seems to be a bulletproof portable, I think RIDGID’s R4510 table saw really shines. Its sturdy workaday features, powerful motor and well-designed stand show that portability doesn’t have to mean compromise. This is an excellent woodworking choice for 10″ portable table saws.
After cutting a bunch of wood with this saw, we really liked the balance of power and portability of Bosch GTS1031 – and I think that’s what this saw is all about. For raw Performance, the unflappable motor-blade combo earned a stiff 8/10 in our tests, while its affordable $399 price tag put it at a solid 9/10 in our Value scale. Sure, you can get cheaper portable table saws, but you’ll find it a challenge to track down the combination of power and portability the Bosch GTS1031 offers. Bosch’s gravity rise-equipped 4100-09 remains a compelling alternative or those wanting an integrated stand. It occupies an additional 15″ in width and 8″ in length and is a full 3.5″ taller. But it only tacks on 8 pounds in weight. If you’re cutting larger pieces of wood or need a saw with a stand, the 4100-09 may be your baby, but the new Bosch GTS1031, with its “toss it in the truck” form factor is our new sweetheart tool. While it has an available GTA500 folding table stand accessory, the real advantage of this saw is it’s stand-free portability – so don’t make it into something it’s not. After using this tool, we think you’ll want to take it with you, as-is, just about everywhere!
The 15-amp motor is outstanding, developing up to 4HP and operating at a speed of 3650RPM. This is not quite as pacey as the DeWalt but still more than respectable. The other advantage to this motor is that – for a table saw, at least – it’s pretty quiet. Noise isn’t such an issue out on the job site but if you’re woodworking at home, the quiet motor is a real boon.

To ensure that our runout measurements were accurate, TBB used a Freud calibration plate. Freud manufactures this ground stainless steel plate to a tolerance of ± .0005 inches in flatness across the plate. While TBB does not have a means to measure the accuracy of this specification, we did put this calibration plate on top of a polished granite calibration table and could not shine a light under any portion of the plate or slip the 0.001 feeler gauge under the edge.

We took all of the data from the RPM and AMP measurements and added them to come up with the final performance rankings. For each saw we added up the total percentage decrease in RPM’s (for each material type) and added that to the total percentage increase in AMP’s (for each material type). This gives us a relative comparison of each saw over all 6 sets of data.
Dust capture from this saw is pretty bad. I was shocked that a European brand would ignore the dust collection to this extent – at least I was until I discovered that their version of the 4100 does have quite a few more pieces that help pull most of the dust from the airstream. There is a plate that encloses the rear around the vacuum port and a bottom grid that allow airflow to the motor while still shaping the airstream to drive the dust to the vac. I added the plate, but decided against the grid. Instead, I added a sheet of ¼” plywood and put a 4” vacuum port in it that I hook up to my dust collector. I also replaced the blade guard with the European version that has a dust port built in. Minor upgrades, but dust capture has gone from terrible/non-existent to pretty acceptable. Bosch also sell a bag that will capture whatever dust would get tossed out the back of the saw, but that isn’t much, so I consider it a waste. I did buy it, and it works well on other tools, but it is not IMO a must-have for the 4100
I got the Hitachi 1 1/2 mouths in the motor died. Says it has a 5 year warranty. I’ve been trying for weeks to get it resolved. Ended up giving up and headed to buy another saw. I understand having products be faulty it’s a numbers game it has to happen to some one. How ever the complete no help to resolve it from Hitachi. Is a problem after a week of back and forth they said they would set up a pick up time to ship and get it repaired over a week still no call back for a pick up. I can’t say enough avoid this headache. I’ve been a contractor for a decade and have had may tools break or need repair. First experience I’ve had that’s made me swear off a brand.hope this will save some one from wasting money and time
This is a truly great saw, except that it is really tough to adjust the blade and rip fence for parallel. Once adjusted though, it is a fine piece of engineering. What I like best is that the saw is built for the job site. It is extremely beefy, but no too heavy. In my opinion, it strikes a nice balance. Its cart stand is the best in the industry, bar none. Once adjusted, the saw returns to its settings extremely well. It is obviously built for the long haul, and should last a contractor many years. I would definitely purchase this saw again. Now with the things that I wish were better. First, adjusting the blade for parallel is just plain hard. Mine was out from the factory by 4 thousandths. It is a trial and error process, and the instructions suck. Here's what to do: 1. Loosen the four screws indicated in the instructions. Starting from behind the saw, center the blade housing in the rear left to right as best you can, then tighten one screw not quite snug (you want the housing to rotate on this screw when you adjust the front). Next move to the front of the saw and loosen the lock lever for blade angle adjustment (the housing won't move unless you do). Now, begin experimenting with holding the housing at 90 degrees with one hand while sliding the housing back and forth with the other until square. When you think that you are close, lightly tighten one of the front housing screws. Check for parallel (look for videos on how to check a table saw blade for parallel), then tighten the blade angle adjustment lever. With these screws and the lever tight and locked, check again for parallel. If it is still good (I got it to 1/1000 inch of parallel), then lock all the screws and check one more time, if it's still good, then you are done with blade housing adjustment.
Todd Fratzel is the Editor of Tool Box Buzz and the President of Front Steps Media, LLC, a web based media company focused on the Home Improvement and Construction Industry.He is also the Principal Engineer for United Construction Corp., located in Newport, NH. In his capacity at United he oversees the Residential and Commercial Building Division along with all Design-Build projects.He is also the editor of Home Construction & Improvement.
Balancing heavy-duty durability and lightweight design, this machine proves that good things can come in small packages. While buyers are overall happy with their purchases, they do seem to all agree on one thing: the DEWALT DWE7480 may be an overall investment, but it could seriously do with a miter gauge replacement. Buyers report replacing its inaccurate, plastic gauge for a solid, more detailed one.
Even a newbie can go around the table saw section at the local home improvement store and feel that some saws have easier adjustments than others. Some are simply easier while others are downright innovative in various ways. Porter-Cable came out of the value group for the overall win with adjustments that are both smooth and intuitive. Dual adjustment wheels mean that you’ll be able to accurately adjust your blade height and your bevel angle—a feature no other saw in this group has.
The price is okay. SawStop is a well-known manufacturer, and they have a pretty good quality control department. In simpler words, it may seem expensive to some, but it’s well-worth the money, especially if you’re a professional. A vast majority of DIY enthusiasts don’t want to make a huge investment in order to tackle a few minor projects; therefore, most of them tend to skip on buying a professional cabinet saw.
Looking for a better way to take care of your wood cutting and still attain a professional result from the comfort of your home? Skil table saw with folding stand will provide exactly that. The foldable stand makes it convenient for any room use and storage. When the table saw is not in use, you can fold it right and use the space for other activities. It’s therefore suitable for small space users who are interested in professional cutting. Another interesting factor about Skil table saw, is that it cuts through materials that are 4 times the normal size. Therefore, instead of cutting each piece individually, you can set several materials to reach the height capacity for easy cutting. Additionally, the fence of this saw will guide and balance your material for accurate results. The saw also features huge blade to make the work easier and interesting for every user. If you invest in Skil saw, you will not only control your cutting but also upgrade your work to the level of expertise even if you are just starting off.
The blade is a 24 tooth carbide tipped blade that is durable and long lasting. You can even adjust it to a 45 degree angle for those more difficult bevel cuts. If you’re working on uneven ground, you’ll love the rear feet that are fully adjustable so you can level you work space. You’ll get a lot of use out of the onboard storage that will give you easy access to the push stick and guarding components. Weighing only 45 pounds, you can move the table saw from work site to home with ease.
It’s the best of the three at keeping your shop clean. The SawStop has a blade guard and arbor enclosure that’s engineered and sculpted to maximize vacuum suction at the cutting edge. Plus, the guard hugs tightly to the blade, and like the Jet, opens at each side so that whichever way you’re cutting, dust goes down the vacuum chute instead of off to the side of your workspace. It’s lab-tested to be up to 99% effective, and it’s certainly the most impressive dust collection system we’ve seen to date.

You often find that many contractors have a love hate relationship with blade guards. Many contractors and woodworkers simply find they often get in the way and can often get wood stuck in them. But many manufacturers are improving these guard’s year on year and now many of them are very advanced and will help keep your fingers from getting hurt, we always advise you to consider the table saw blade feature on any table saw in detail as it could one day help saw you.
If you are just learning how to sharpen your table saw, you may wonder how to know when to sharpen your saw using your best table saw grinder. You do not want to end up sharpening it too much because that will damage your cutters. It is dangerous to work with a saw that is not sharp enough. Dull cutters tend to catch in the materials and propel the bar in the operator’s direction.
The saw itself is remarkably compact, measuring just 22.5″ square and a little over a foot in height (13″ to be more precise). With a steel “roll cage” that encloses the 4 HP 15-amp motor and a rubber handle that is positioned in the center of the right side of the saw, this is a tool that you’ll find very easy to toss into the back of a pickup or work van and take to any jobsite. When you carry it deck-inward, the weight of the saw presses in slightly against your leg – which actually steadies the saw somewhat, making it more manageable, though at 52-pounds let’s not go so far as to call this saw a breeze to carry. The Bosch GTS1031 included cord wrap, and the simple design of the frame also makes it easy to store up against a wall inside your shop when not in use. This isn’t a tool that really gets in the way much – it’s out of sight until it’s needed.
A splitter is a piece of metal that keeps the blade from binding in whatever material you are cutting if the saw kerf starts to close up. The splitter is vertical and sits directly behind the blade. This plays a big part in preventing kickback and should be mounted on the motor assembly so it rises and falls with the saw blades movements. You can also get splitters that can be adjusted to fit the width of the kerf.
Table saws will continue to be popular and much sought after tools in any workshop or construction site. There are many terrific styles on the market which is why it is important to do some research and look at the reviews provided here as well as the tips contained in this guide to help you choose the right table saw for your needs, whether you are a professional or a DIYer who loves to work in the workshop making things for enjoyment.
Probably one of the things that users will love most about this table saw is the solid granite surface which offers a seamless work area and excellent support. Another advantage of the Steel City 35955 is the fact that it comes with powerful magnets which allow swift changes without having to worry about using any type of tools. Since there’s a built-in mobile stand, you can easily position the saw around your shop without requiring the help of a second person.

Pre-calibrated right out of the box, Kreg’s miter gauge is a blessing for the impatient among us. The folks at Kreg know their customers don’t want to waste time preparing their tools — they want to use them! That’s why the KMS7102 boasts positive stops at a variety of the most common angles: so you can begin using your brand new miter gauge straight away.
Let’s face it: guys get in each other's’ way at a job site. It’s not always easy to find room to work, so portability is a serious advantage when it comes to making the most out of your space. Luckily for the professionals out there — not to mention hobbyists who prefer to move around rather than work in the same spot everyday — RIDGID’s 15-amp table saw comes with a convenient mobile cart for stress-free transportation.

You often find that many contractors have a love hate relationship with blade guards. Many contractors and woodworkers simply find they often get in the way and can often get wood stuck in them. But many manufacturers are improving these guard’s year on year and now many of them are very advanced and will help keep your fingers from getting hurt, we always advise you to consider the table saw blade feature on any table saw in detail as it could one day help saw you.

6. Clamp rip fence to check if it holds securely at front and rear. If rear is not clamped securely, un- clamp fence and turn rear clamp adjustment screw 6 clockwise for increased clamping. Try clamping the fence to verify if it self aligns and clamps tightly at the front and rear. Overtightening of the rear clamp adjustment screw 6 will cause the rip fence to be non-self aligning (Fig. 23). Overtightening may cause friction or “chatter” when fence is moved side to side.
×