Table saws will use one of two different kinds of drive configurations; Direct-drive motors and Belt-drive motors. In a direct-drive motor, they will link directly to the blade itself and transfer all of the power of the motor to the blade. They tend to last longer than belt drive motors and there is no belt to replace or worry about getting worn out. Belt drive motors transfer power from the motor to the blade through a belt. In this type of configuration, the motor can be offset away from the sawdust which helps the motor last longer. In general, belt drive motors need more preventative maintenance than direct-drive motors do. If you have a belt drive motor, check the tension of your belts as well as checking them for wear periodically to ensure your continued safety.
Let’s face it: guys get in each other's’ way at a job site. It’s not always easy to find room to work, so portability is a serious advantage when it comes to making the most out of your space. Luckily for the professionals out there — not to mention hobbyists who prefer to move around rather than work in the same spot everyday — RIDGID’s 15-amp table saw comes with a convenient mobile cart for stress-free transportation.
However, there were some limitations. The rip fence build, with a thin-metal body, is light-duty. At just 23⁄4″ wide, the saw’s narrow throatplate makes it harder to reach down inside for swapping blades or retrieving a fumbled arbor nut. While the white-on-black bevel scale display is easy to read, the thin red hairline pointer that marks tilt angles disappears over the top of it; the saw needs a larger, brighter indicator. There’s a geared mechanism for tilting the blade that engages when you push the blade height wheel in — a good thing — but the bevel lock lever is too short, and I would use care when bearing down on the plastic handle to tighten it.
It’s powerful. The blade is hooked up to a 3HP motor which can muster a no-load speed up to 4000 RPM! That’s perfect for all your cutting needs, and it’s much better than other inexpensive units when it comes to slicing hardwoods or thicker stock. While many smaller units advertise similar HP ratings, this one actually lives up to the promise, since it uses 220V power.
The TruePower 01-0819 may look like a miniature version of a table saw — and that’s because it is! Ideal for hobbyist modelers and DIYers looking to tackle minor jobs, the 01-0819, while lacking the same power and performance as its larger, pricier counterparts, is a steal at under $50. A must for any toymaker’s workbench, this bite-sized machine measures in at 8.5" x 7" x 7", and while it lacks important parts like a guide fence, it gets basic 1/2" wood or foam board cutting jobs done, slicing through softer materials with ease.
I am looking to upgrade from my first table saw which is the Ryobi that you reviewed (had to find something cheap that was decent). I do a lot of rip cuts, as well as fine precision cuts for laminating and joinery required for frames, furniture, etc. I am looking at the Skilsaw and the Dewalt 7480 and cannot decide which would be best for me. Any insight would be helpful!
The cabinet also has a few other safety features that set it on a level above the Grizzly or Jet. There’s an extra-large, paddle-style power switch which you can easily press with a thigh as well as a hand. The guard works tightly against the blade, so that you have all the workspace you need without sacrificing safety. The riving knife prevents kickbacks, and the left-tilting bevel feature prevents binding.
I can’t tell you how many times we’ve pulled out other jobsite saws only to have accessories fall off, or require off-tool storage. Bosch designed the GTS1031, however, to securely hold all of its accessories, even including the arbor wrenches (both of them) and an allen wrench for adjusting the riving knife and dust ejection points among other things. Our favorite was the rip fence, which simply flipped upside down and stored underneath the table – clever! About the most difficult adjustment was the riving knife, which is a tool-less maneuver, but one which requires you to stick your hand way into the blade cavity to reach the release lever. When making any adjustments to the blade, it goes without saying (but we’ll say it anyway) to disconnect power to the saw as a precaution.