Plus, it’s simply a great table saw in its own right. It’s powerful, efficient, and quiet. It cuts through all kinds of stock smoothly and easily, and the dust collection system helps it clean up after itself. Previous buyers who upgraded to this one said that the transition from their old cabinet units felt like switching from a family sedan to a sports car. We recommend it to anyone looking for the absolute best quality, for small to midsize pro shop work or the passionate home woodworker.
The JET ProShop Table Saw offers features you The JET ProShop Table Saw offers features you expect from a high-end cabinet saw in the compact design of a contactor-style machine. The transparent blade guard has independent leaves and the quick release riving knife reduces chance of kickback. A low profile riving knife is included for non-through cuts.  More + Product Details Close

TBB measured the accuracy of the factory-set 45 degree stop by using a Wixey WR365 digital inclinometer. This device has an accuracy of 0.1 degree. We placed the Wixey gauge on the table and calibrated the inclinometer to the table by zeroing out the gauge. After that calibration, the measurements shown on the gauge give a result that is relative to the saw table. We attached the gauge to the blade and used the saw mechanism to adjust the blade incline to the point at which the blade or trunnion hit the factory-set 45 degree stop and recorded the measurement. TBB ran the test twice to ensure the repeatability of the measurement. In every case, the result came out to within 0.1 degree of the prior test.
Kickback (if you didn’t already know) is one of the most common accidents with table saws. In order to prevent this you can make use of the riving knife (you may also find this referred to as a splitter). When the material gets pinched by the blade at a certain angle kickback occurs, but thanks to the riving knife there is no chance of this happening.
If the blade you purchase has a .092” kerf (i.e. Irwin Marathon 80T, FreudLU83R010) you will most likely have issues with binding on the back end of the cut. To be safe, find a blade that has a kerf of around .098” (i.e. Freud Avanti TK905 50T) and this should take care of the problem. You should also take note that every blade Bosch makes should also work with the Bosch 4100-09.
One of the biggest perks of a cabinet table saw, aside from the rugged construction and wide worktop, is the sheer power of the tool. You should expect a cabinet table saw to cut absolutely any stock within its depth capacity smoothly and easily. Look for motors with at least 3 HP, and sophisticated belt drive systems which translate that grunt into 4000+ RPM blade speeds. Don’t accept lesser power ratings on a cabinet model: these are the gold standard of table saws for a reason!
If you’re a home DIYer or pro working mainly from a shop, you may have a wide table or countertop big enough to use the saw without any accessory stand. We would caution against working on sawhorses, though, as they can be wobbly and unsafe. It’s far better to spend a few extra dollars on a sturdy stand than to take risks with a rickety, improvised setup.
Table saws are undeniably the kings of rip cuts on the jobsite and in shops. The concept is simple: Place a motor below a solid table to turn a blade somewhere in the 4000-5000 RPM range through the surface and watch the sawdust fly. The idea may be simple, but the reality is much different. How big should the table be? What size blade should you use? How heavy can you get away with making it?
Likes: Cuts extremely well and has excellent stability. Its blade guard and riving-knife assembly are locked and unlocked by a lever located conveniently along the table's left edge. A simple, separate shark-fin riving knife can be used when the guard is too big for narrow rip cuts. We appreciate the antiglare surface on the tape ruler that measures the distance from the blade to the fence.
Probably one of the things that users will love most about this table saw is the solid granite surface which offers a seamless work area and excellent support. Another advantage of the Steel City 35955 is the fact that it comes with powerful magnets which allow swift changes without having to worry about using any type of tools. Since there’s a built-in mobile stand, you can easily position the saw around your shop without requiring the help of a second person.
Lowes had a Father’s day sale, on their Kobalt table saw with a folding/rolling stand and was $180.00, with more money off because I signed up for their credit card-so I bought it. It cuts fine, the fence locks on both ends,measurements seem ok, and it unfolds and rolls away very easily-I like it so far. I’m a home owner and I use it sporadically and treat it well, it does not appear to be very robust, so as a day to day, on the job site saw, probably not a good choice. I used to have a Makita table saw, with a terrible fence, unreliable ruler markings, and difficult to use blade guide that interfered with measurements, which you needed to do every time-a terrible saw, very frustrating to use. I have a Makita miter saw and it’s great, but the idea of buying a same brand because I liked one of their other products did not work out.

If height adjustments were standardized, we could expect each saw to make them nearly identically. Taking a look under the hood, we discovered several different methods—each with their own effect. Most of the saws employ a bevel gear system that provides smooth and reliable performance. We noticed that many used solid metal gearing, but Bosch used plastic for both the 4100 and the REAXX.


But, their price point reflects that. If you want the absolute best table saw money can buy then you can go pay $10,000 and it’s yours. We always accept a certain number of tradeoffs depending on what our budget allows So, if I am only doing a few DIY projects a year, I am not a carpenter by trade, and my budget is limited, the SKIL table saw may be right up my alley.

While it’s bargain-priced, it has very impressive cast iron and steel construction, with all the same essential features as our other top table saw recommendations. On the downside, it’s the slowest of the three in terms of blade speed, and it has the shortest warranty coverage. This one also lacks some of the sophisticated safety features and creature comforts of our more expensive recommendations.
Sadly, you will have to sacrifice in a few key departments for all that portability and convenience. Portable table saws are the worst choice for cutting larger stock, especially if you don’t have an extension table to add on. They’re also the least powerful sort of table saw, so you shouldn’t plan to cut thick stock or hardwoods on them regularly. Thanks to their light build, portable units are the loudest of the bunch, and their dust collection is usually less than impressive. However, if you’re moving around a lot and need to do rips in the smallest possible space, these are your best friends.
Different types of table saw rely on different motors. With the smaller and more portable saws, 120V direct drive motors can deliver up to 2HP. This is more than enough power if you’re working with less substantial sheets of material. The larger saws have belt drive motors running on 240V. These produce 3-5HP. Think carefully about the materials you’ll be working with. Get the right sized motor for your cutting needs.
The DeWalt will do you proud for a broad spread of applications. If you’re a home woodworker, you’ll be able to rip sheet material, size material as thick as 3 inches, frame lumber and make cross cuts to your heart’s content. For professionals, the DeWalt is perfect for trim carpentry, installation of hardwood floors, decking or remodeling. There’s very little you can’t do with this beast.

While you may be tempted to skip straight to the reviews, they are a bit on the technical side and contain plenty of terms you might not be familiar with just yet. My suggestion would be to start by reading the informational articles which will provide you with a decent amount of knowledge on table saws. After that, I sincerely doubt you would be caught off-guard while reading anything in the review section.
Another excellent choice for the hobbyist or at-home handyman, the SKIL 3410-02 10-Inch Table Saw is a great value, giving you a durable build and quality performance at a wallet-friendly price. It doesn’t have the same brand recognition as some of the more expensive options on this list, but reviewers love this machine and say that it’s perfect for woodworking and DIY projects.
Install new blade- With the new blade, face the teeth of so they are pointing to the front of the saw table. Place the blade on the housing. Secure the new blade with the washer and nut with the use of a wrench. Make sure you are turning the wrench in a clockwise motion. Use the small piece of wood to secure the blade in place while you are securing it.
Setup was nearly as simple as SawStop’s with just a narrow margin between them. We only needed to attach the handle and bolt the saw down to the stand. The stand is a gravity rise style, but requires you to bend down to ground level for collapsing and extending it. It’s a reasonably solid platform, though a lot of movement throughout the day will leave your back sore.
We really should point out a big deal here and that’s the SawStop. It’s hard to put a price on safety and while the SawStop costs more than 3 times what the Hitachi costs it does offer safety that no other saw in test can offer. For those that can afford the additional cost that feature alone may tip the scales for you. Regardless of price SawStop came in 5th place for the categories we evaluated.
Perfect for both hobbyists and craftsmen, the PCS31230-TGP252 from SawStop is a 3 HP cabinet saw that delivers excellent performance while featuring the company’s patented safety system to ensure maximum safety during use. The safety system is similar to that of the G0690 from Grizzly where the blade stops in milliseconds after it comes in contact with flesh. Designed and built in order to satisfy the needs of the most demanding users, the PCS31230-TGP252 features an exacting finish and feet and a superior dust collection system. For increased precision and added strength, the PCS31230-TGP252 features a fifty two inch T-Glide fence system, but also an extension table and rails.

The simplest way to find out what size your table saw needs or indeed if you’re buying a special size is to consult the table saw user Manuel. I would make sure you do this as often there are many things in modern tables saws that could affect the blade size and type. This is because modern saws have many different amazing and varied features, things size blade guards, special safety mechanisms and arbor sizes etc. With the We recommend you spend some time reading your manual in detail to avoid possible issues
For those of you who are looking to up your DIY game but don’t have enough capital to make the Dewalt DW745 happen for your home shop, this Craftsman is a decent budget choice. It’s powerful, lightweight, and extremely affordable. We don’t think you should expect too much from this one, though, since it has a very light table and a fence that won’t line up quite as precisely as you’d need for furniture-making or professional-grade projects. It’s cheaply-made, and doesn’t have as user-friendly a design as our other choices. For the home carpenter, though, this should do the trick for all your basic framing cuts.
The price is okay. SawStop is a well-known manufacturer, and they have a pretty good quality control department. In simpler words, it may seem expensive to some, but it’s well-worth the money, especially if you’re a professional. A vast majority of DIY enthusiasts don’t want to make a huge investment in order to tackle a few minor projects; therefore, most of them tend to skip on buying a professional cabinet saw.
Porter-Cable comes in as the most expensive of the value group, but also with the best overall performance in it. Of the three saws in this class, it had the best cutting power and also came in the top spot overall for height and bevel adjustment thanks to independent wheels. This may seem like a small consideration, but when you actually need to cut accurately beveled pieces, the adjustment wheel is a huge benefit over sliding the front height adjustment around.
Bosch’s 4100-09 work site table saw is a sure win. Bosch never fails to impress us, and this table saw is no exception. It’s a 10 in. saw with a 25 in (right) rip capacity and a 47 degree left bevel. This Bosch table saw is powered by a 15A motor that reaches top speeds up to 3,650 RPM. Another feature we appreciate: its constant response circuits which continuously adapt the speed under load, giving you a continuous blade speed.
Having only owned saws with cast iron tops this is a new experience for me. First let me note that the right side extension is not aluminum like the rest of the top. It is steel, painted to match. The entire top appears to be powder coated with a textured grey coating. No telling how durable it will be but it does allow wood to slide easily over it. Since the top is aluminum, it lets you know that by transferring all the motor noise and vibration throughout the saw. Not a big deal really but definitely different if you are used to the cast iron absorbing much of this on bigger saws.
×