Power protections are also a key safety feature, since they protect both your personal safety and the integrity of your table saw. Look for a magnetic switch in the power switch assembly of your saw. A magnetic switch protects the system from dangerous power fluctuations, and automatically shuts the machine off in case of a surge or drop in flow. It’ll also perform another valuable function when power goes out or a fuse flips: it’ll prevent the saw turning itself back on when power returns!
Bosch’s REAXX and SawStop were neck and neck with near perfect cleanup at the collection point and only a slight amount of dust coming out toward the user. What did make it out was even less coarse than the other Pro level saws. Both saws have narrower throat openings for the blade that reduce the amount and size of material that can make it out. In the end, SawStop produced less top dust than Bosch did to earn the win.
Portable or “jobsite” table saws are the absolute opposite of cabinet models. These are the lightest, most travel-friendly table saws on the market. These are easy to pack up and store in the back of a pickup truck or work van, and they can be set up pretty much anywhere. You can fit them to folding stands, use them on countertops, or sawhorses. We love them for quick contractor jobs, and they’re the ideal tool for general handymen who do a lot of shorter jobs rather than extended carpentry fittings. These are also a great entry-level choice for DIYers who don’t need a massive table saw, but need something that they can pack away at the end of the day. And, of course, they’re the least expensive table saws you can buy!
This saw has a soft start and also seems to over-rev and then slow down to correct itself upon startup. Strange, and I'm hoping this isn't a precursor to a problem down the road but for now it works fine. The Bosch blade that it comes with was removed and replaced with a Freud. The saw cut like a hot knife through butter and I am very pleased with the overall performance. The miter gauge is a little sloppy in the miter tracks.
The fact is, a table saw is designed to remove a large amount of material in a quick and efficient manner. With the volume of waste that is produced by any but the smallest table saws, a shop vacuum is not going to be up to the task. Short of purchasing a standalone dust collection system, the best that you can hope for from a shop vacuum is that it might keep some of the saw dust out of your eyes.
This “review” is a giant nothingBurger. There is not one scrap of objective comparison between these saws. Because you sell them, they’re all great and will all zip right through “the hardest woods”. Bulll$hit. You did not test, compare, analyze, or use ANY of these saws. Re-hashinf manufacturer specs is a “Roundup” but it certainly is not a review. Typical sales pablum.
No matter the model or price, a table saw should cut a range of material thicknesses and hold its settings accurately. So, after installing a new Freud hi-ATB thin-kerf blade in each saw, I made repeated rip cuts on MDF, resetting the fence each time to check for consistently thick offcuts. After that, I raised the blade for more rip cuts on heavy, long planks of 2 x 12 Southern yellow pine, before tipping the blade to bevel-rip 2″-thick poplar. Then I switched to a 6″ CMT dado set and made a long dado cut in MDF, so I could check for consistent cutting depth — a sign that the undercarriage is stout enough to handle a heavy blade like this. Overall, my test criteria was stability of the stand, cutting accuracy, reasonable dust collection efficiency and all-around convenience of use. Results ranged from exceptional to mediocre, as you’ll see.
Give yourself a reason to smile every time you enter in your workshop by investing in this powerful instrument. DEWALT as a company guarantee quality in all their products for the interests of customer satisfaction. This Jobsite table saw is not exceptional. Its designed to provide precision and last longer. The saw features pinion and rack system that makes adjusting the fence easy and convenient. In other words, you will not strain or shift your concentration while on work. The table saw is designed with a rolling stand that guarantees you professional performance in all your cuts. It also features telescoping fence rails that retract and extend for a small portable package of the saw. Additionally, the table saw is suitable for both wide and narrow rip cutting as the fence can adjust based on the type of material you are cutting. Using a 15amp motor, you are sure that the saw will get the job done within minutes and save you energy cost.
Another important safety feature to consider is a magnetic switch. Magnetic switches are there in case of power cuts or outages and will also protect the table saw motor from over load. Effectively it will switch off the power supply the instant the power goes off ensuring you don’t have a saw blade spinning away in the dark! As you can imagine this is a very useful and must have safety feature when looking to purchase a new table saw.
If you’re going to be transporting your unit regularly, you should aim to keep weight to a minimum. Look for something lightweight, with convenient carrying handles, or a stand that can be wheeled around dolly-style at the worksite. Conversely, if you’re only going to be using your portable saw occasionally, you can probably stand a bit more weight.
This woodworking website has tons of information about how to use a table saw: choosing blades, cutting joints, safety features, and more. However, we found only five actual product reviews, none more recent than 2013. Although these individual reviews are hands-on, they don't put saws through any specific, detailed tests. There's also no direct comparison between saws and no formal rating system.
Using the guards the saw came with is crucial for the safety of your hands. If you are working with smaller pieces, make or buy a sled with a work clamp so that you can maintain a safe distance from the blade. The clamped sled can be as simple as a piece of plywood with a track on the bottom that’s responsible for riding in the groove. It’s quite simple to construct, saves time, and most importantly – fingers.
Table saws cut more or less the same way as a circular saw (covered in their own report): a round blade, usually 10 inches in diameter, spins as it works its way through the wood. The main difference is that the blade is fixed in place, sticking up through a gap in the table, and the operator moves the wood past the blade instead of moving the saw itself. Table saws support and guide lumber and wood panels as they pass over the spinning blade, making it easier to make accurate repeat cuts than with a circular saw.
In terms of size, the table height from floor measures thirty four inches, with extension it measures twenty seven by forty inches and overall dimensions are 62 by 41 by 40 inches (LWH). This is simply an amazing saw and not only will you use it for many years to come, but it’s going to help you get the professional results you’re looking for in any project.
I also added in a bicycle saddle bag, that attaches easily to the tube frame of the saw. In it, I keep my PPE, and my Grr-ripper push blocks (great upgrade over regular push blocks). I also have a push stick made of wood that was modeled after the plastic one mounted on the back of the saw. The wood one is there now. I read too many stories of injuries after the blade touched the plastic stick, which to me is the whole point of using a stick – to avoid injuries. These things turning to shrapnel seems like a bad idea.
If you’re a professional woodworker, you should expect a standard hookup on any saw. However, you’ll find that no portable table saw does a perfect job collecting sawdust. Since these aren’t enclosed tools like a cabinet saw, there are lots of ways for dust to find its way to your floor and spray around your shop. You’ll want to look for the most enclosed, effective design possible, and pair it with a vacuum system that’s got some heft.
If you want to take the saw with you and use it in a different location, you can purchase the optional MB-PCS-000 integrated mobile base which features 2 stationary casters and 2 pivoting casters. Furthermore, it’s also possible to upgrade the mobile base assembly to a one thousand pound lift capacity, add a hydraulic piston lift and 4 independent pivoting casters.
On the downside, Delta have changed things up over the past few years, and the news isn’t all good. The motor is still made in the USA, but the frame and structure of the saw is all imported. Recent buyers have reported shoddy quality control and very poor customer service since the company was taken over. Even though the Unisaw still gets great professional reviews, buyers’ experiences are so mixed that we’re not comfortable recommending this one as one of our top picks.
The fence on this system is easily the winner. With clamping on just the front side, it self-aligns better than any other in the group and offers excellent stability. While SawStop didn’t have the most powerful feel to the cuts, it was very smooth with little vibration. Feature preferences aside, the only (slight) negative we agreed on was that the bevel lock stuck a little bit compared to others.
It also has the highest blade speed. This model has a similar 15-amp motor to our other recommendations, but it’s geared for maximum efficiency. The result is a blade speed that’s nearly 1000 RPM better than the Bosch or the smaller Dewalt. Reviewers marveled at how powerful this one was compared to the size of the motor, which seems underwhelming from the outside. It rips right through oak, cherry, and other planks with no lag or burnout. In fact, we’re hard-pressed to find something this would struggle to cut, provided you equip it with the proper blade.
We don’t always post the point totals when we do a shootout like this because it gets complicated – you have to decide what the important features and performance categories are, determine how much weight each one should hold, and then actually hash out the scores with the team. That said, some of these table saws scored so close to each other that I didn’t feel it was fair to just leave it up to the rankings.
Since this is a high end cabinet table saw, its features are on par with your expectations. This model comes with your choice of cast iron or stamped steel wings. Kickback is also greatly reduced thanks to the quick release riving knife, while the transparent blade guard comes with independent leaves to complete the set of features you’d expect from a Jet Proshop table saw. If you want, you can also get the Jet Proshop table saw in either a thirty inch or a fifty two inch rip capacity. No matter if you’re a professional or if this is the first cabinet table saw you’re planning to get, the 708494K JPS-10TS won’t disappoint. Its rugged build quality and ease of use qualify it as one of the best table saws you’ve ever used.
The SKILSAW SPT70WT-01 is truly a woodworking marvel, packing a 15-amp Dual Field motor into a surprisingly lightweight yet durable 49-pound frame. Whether you’re an amateur carpenter or a contractor with years of experience under his toolbelt, SKILSAW’s workhorse of a table saw is an invaluable addition to your repertoire thanks to its raw torque and unparalleled 25" ripping capacity, meaning tearing through thick sheets of plywood has never been easier.
TBB used an iGauging 35-125-4 digital dial indicator to measure the accuracy of the blade position to the table miter slot. This instrument has an accuracy of .0005 inches. As part of the table saw set-up, TBB installed a new Diablo blade in each saw and these never-before-used blades were used in the measurement test. To ensure that any wobble in the blade did not enter into the test results, TBB marked a single tooth as the reference point for the measurement. The blade position was moved to the front of the saw to allow the iGauging dial indicator to hit the tooth immediately behind the carbide tooth, The iGauging dial indicator was calibrated and the indicator had a reading of zero.
Bosch GTS1031 10 in. portable jobsite table saw is powered by a 15 Amp motor that allows this table saw to rip through any lumber or hardwood quickly and easily. Bosch’s Smart Guard System provides added control while cutting, SquareLock Rip fence ensure consistent and accurate cuts, and an all steel base provides added durability. Oh yeah, and we forgot to mention the price. This is the most affordable table saw on our list!
You’ll want to look for metal framing, and a design which allows for all the most delicate components to be stored inside the tool’s body. If you’re a DIYer who won’t be travelling with your saw often, you probably don’t need to worry about finding such a heavy-duty frame. Many portable units will fit easily on the passenger’s seat, so you won’t have to deal with wear and tear so much.
Just used this saw for the first time today and I love it. Instructions for putting the stand together were not very clear. There's a lot of very detailed reviews here, so there isn't much I can add that hasn't already been said; but one thing I didn't know until using it is that the rear legs are angled further back than the front ones to provide more stability when pushing stock through the saw. Only used it a few times today, but it was a pleasure to use.
When I switched blades, I did find the locking lever for the riving knife very stiff … not sure why. It raises to release the riving knife and pushes down to lock it. I resorted to gripping the lever with a pliers to manipulate it, after nicking some skin on the blade teeth. But, on the softer side, RIDGID provides a nice complement of overmolds on the miter gauge handle and blade height handwheel knob.
It has a brilliantly powerful 15 AMP motor, which can deliver 4,800 RPM of cutting power. Is is normally more than enough for most woodworkers and hobbyists. It has stowable anti-kickback pawls and and excellent riving knife and spreader for accurate cuts. This is a great entry level saw at a great price, definitely worth looking at for your next purchase or project.
Our top midrange choice comes from Jet, which is a partner brand of the well-known Powermate lineup. This unit is a good choice for folks who need a saw that can cut through absolutely anything, at a reasonable price, and without taking up too much space. It’s more compact than the Grizzly, but it offers even faster saw speeds and more precise adjustments. We recommend it to folks who want lots of power, but don’t have the room for a larger cabinet unit.
The first step to take when using a table saw is to don all the appropriate safety gear that a responsible operator should use. This includes, at the bare minimum, eye protection and thick work gloves. It's also a good idea to protect your ears with ear muffs or earplugs and to consider a mask that will cover your mouth and nose to prevent the inhalation of fine saw dust particles.
The power transfer system is neatly done. The model features a serpentine belt which is quiet and smooth during operation. Therefore, the level of noise is satisfactory. Precision is something that makes this model worth checking out. Whether you’re a professional or a beginner, you’ll definitely appreciate the accuracy of this model. On the other hand, with great things come great responsibilities. Don’t forget to wear safety equipment!
From there, it’s all about flesh detection. The REAXX wins out over SawStop in this category thanks to quicker recovery, a two-shot activation mechanism ($99 per cartridge, $49.50 per shot), and keeping the blade from damage. The initial saws to go out also come with a code to get an extra cartridge for free when you register the REAXX. Like I mentioned earlier, the unknown is still the actual reaction time compared to SawStop.
Stands are one of those features where the ends really do justify the means. Some made us wish the manual writers would take a cue from Lego—just make the *@#$! things easy enough for a 7 year old to understand. That aside, SawStop set itself aside brilliantly, taking just 10 minutes to setup. All we had to do was install the wheels and two handles. Even the packaging is designed to make the process easier and the instructions were super-easy to understand. Makita was nearly as simple only requiring us to install the handle and bolt the saw to the stand.
Sadly, you will have to sacrifice in a few key departments for all that portability and convenience. Portable table saws are the worst choice for cutting larger stock, especially if you don’t have an extension table to add on. They’re also the least powerful sort of table saw, so you shouldn’t plan to cut thick stock or hardwoods on them regularly. Thanks to their light build, portable units are the loudest of the bunch, and their dust collection is usually less than impressive. However, if you’re moving around a lot and need to do rips in the smallest possible space, these are your best friends.
If the fence and the miter slot were closer together at the rear of the saw, the dial indicator has a negative reading. If the blade and the miter slot were father apart at the rear of the saw, the dial indicator showed a positive reading. A negative reading meant that the materials being cut might be subject to being pinched and a kick back more likely to occur.
Below is a graph showing the average measured decibels for the saws (for each of the materials we tested). As you can see the saws range from 93.7 db to 97.9 db. OSHA allows 8 hours of exposure for up to 90 db, from 95 db up the exposure limits start dropping quickly starting at 4 hrs for 95 db so clearly these saws all need hearing protection. We ranked the quietest 3 saws as a 2, and the remaining saws as a 3 and felt none should rank a 1 due to the need for hearing protection.
The larger the motor, the higher the voltage as well, usually 240V. In some cases, you may be lucky and have a garage or workshop that’s wired for 240V, so that is why it’s very important that you check this prior to getting the table saw. In terms of the material thickness it can handle, it’s a minimum of three inches. One thing to bear in mind is that safety is an essential consideration with these saws and that’s because the powerful motors are prone to higher kickback.
While you may be tempted to skip straight to the reviews, they are a bit on the technical side and contain plenty of terms you might not be familiar with just yet. My suggestion would be to start by reading the informational articles which will provide you with a decent amount of knowledge on table saws. After that, I sincerely doubt you would be caught off-guard while reading anything in the review section.