Measuring 30.31" x 17.32" x 41.81", this powerhouse boasts a heavy duty 10" blade that can cut up to 4" x 4" of material in a single pass. For the handyman who likes to keep all of his tools within arm’s length, RIDGID’s table saw comes with convenient onboard storage so swapping out blades or accessing your tools is just a short reach away. Buyers are crazy for this table saw, and they report that it easily fits into the corner of their garages. Plus, quick and easy assembly means you can get to work straight out the gate.


No matter the model or price, a table saw should cut a range of material thicknesses and hold its settings accurately. So, after installing a new Freud hi-ATB thin-kerf blade in each saw, I made repeated rip cuts on MDF, resetting the fence each time to check for consistently thick offcuts. After that, I raised the blade for more rip cuts on heavy, long planks of 2 x 12 Southern yellow pine, before tipping the blade to bevel-rip 2″-thick poplar. Then I switched to a 6″ CMT dado set and made a long dado cut in MDF, so I could check for consistent cutting depth — a sign that the undercarriage is stout enough to handle a heavy blade like this. Overall, my test criteria was stability of the stand, cutting accuracy, reasonable dust collection efficiency and all-around convenience of use. Results ranged from exceptional to mediocre, as you’ll see.
Kobalt’s KT1015 Table Saw features value pricing with a decent rolling stand. We initially had questions about its dual-locking fence, but found that it actually worked quite well. There’s plenty of wobble in it, but if you follow our Pro Tip on adjustments in the fences section, you can lock the front end in square then stabilize it with the back lock.
One of the first and most important things to consider is what type of table saw you require. When considering the type make sure you consider things like, where will be using the saw, will it need to be portable and move from job to job or can it be stationary like in a work shop. Also, what will be the largest size bits of timber I will be cutting, what sort of power will I require and budget, below we’ve listed the main types so we hope it helps you find the right type for you.
As for my blades, I replaced the blade that came with the saw right away. It is terrible and would have been better to be not included at all. I replaced it with a Freud industrial 24 tooth glue-line rip blade and a Freud Diablo 80 tooth plywood and crosscut blade (I find it easier to just buy new plywood blades since the glue does a number on them, not to mention the wear and tear caused by MDF). As an all-around blade, I keep a 50 tooth Tenryu Gold blade. It is quieter somehow, and does a cut almost as good as either the rip or crosscut blade. Great for making quick cuts without always changing blades. I will use it for most ripping, but will switch to the ripping blade when I have a lot of ripping to do, or will be going thicker than about 1.5” in hardwood.
The whole thing is a bit more versatile than the Dewalt, thanks to expanded fence rails and an extended trunnion set. It has a wider rip capacity than the Dewalt. This one uses a traditional sliding-rail fence which gives you a rip capacity up to 25 inches. The fence locks at either side, like the Dewalt’s. It also has a wider bevel range, tilting up to 47 degrees.
While you may be tempted to skip straight to the reviews, they are a bit on the technical side and contain plenty of terms you might not be familiar with just yet. My suggestion would be to start by reading the informational articles which will provide you with a decent amount of knowledge on table saws. After that, I sincerely doubt you would be caught off-guard while reading anything in the review section.
Dust capture from this saw is pretty bad. I was shocked that a European brand would ignore the dust collection to this extent – at least I was until I discovered that their version of the 4100 does have quite a few more pieces that help pull most of the dust from the airstream. There is a plate that encloses the rear around the vacuum port and a bottom grid that allow airflow to the motor while still shaping the airstream to drive the dust to the vac. I added the plate, but decided against the grid. Instead, I added a sheet of ¼” plywood and put a 4” vacuum port in it that I hook up to my dust collector. I also replaced the blade guard with the European version that has a dust port built in. Minor upgrades, but dust capture has gone from terrible/non-existent to pretty acceptable. Bosch also sell a bag that will capture whatever dust would get tossed out the back of the saw, but that isn’t much, so I consider it a waste. I did buy it, and it works well on other tools, but it is not IMO a must-have for the 4100
At a compact 45 pounds, the DEWALT DW745 Compact Jobsite Table Saw is the lightest table saw in our review. The saw's portability doesn't mean that ripping size is compromised, though. Thanks to extending fence guides, you've got 20 inches available. Depth of cut is on par with many bigger machines: at 90 degrees, it's 3 1/8 inches. At 45 degrees, it's 2 1/4 inches. Power comes from a 15-amp motor with a no-load speed of 3,850 RPM. This is ample enough for serious DIY projects and light-duty construction site work.
How do you tell what the best table saw is? With so many table saw choices on the market it’s hard to know which table saw is the best fit for you and your woodworking needs. Not for long. We’ve taken the leg work out by doing all the measuring, tracking, and researching for you. We’ve compiled year-over-year performance and pricing information for over 3 years to help you choose the table saw that is ideal for you and your project. Search no more, find your table saw below.
While I appreciate this review, that Kobalt job site saw is the absolute worst. Uncontrollable blade wobble, terrible fence, trundle bolts that are nearly impossible to get to without tacking the back panel off (of course that doesn’t matter when the blade won’t stay in alignment for more than a day), miter slots that aren’t parallel to each other and also taper toward the backside of the table, and a riving knife without adequate adjustments to align it with the blade. Do not buy that piece of garbage.

If you need to move your saw around, it comes with a table saw stand that you can put up and down with ease. Fashioned from aluminum pipes with wheels that can handle uneven terrain, move around site without breaking your back. As well as its user-friendly nature, the stand can be stored away vertically so it’s a real space-saver whether at home or on the jobsite.
It features an 1850W motor which delivers more than enough power for any heavy-duty task and DIY project. Dewalt is well-known for designing quality tools, and they didn’t disappoint with this particular model either. The fence system offers 610mm of rip capacity. As you may assume, even though it’s a portable unit, you can easily cut large pieces of wood to a particular size.

While you may be tempted to skip straight to the reviews, they are a bit on the technical side and contain plenty of terms you might not be familiar with just yet. My suggestion would be to start by reading the informational articles which will provide you with a decent amount of knowledge on table saws. After that, I sincerely doubt you would be caught off-guard while reading anything in the review section.
Bosch’s REAXX and SawStop were neck and neck with near perfect cleanup at the collection point and only a slight amount of dust coming out toward the user. What did make it out was even less coarse than the other Pro level saws. Both saws have narrower throat openings for the blade that reduce the amount and size of material that can make it out. In the end, SawStop produced less top dust than Bosch did to earn the win.
We were impressed with the Bosch Glide Miter Saw which was revealed in 2010 and revolutionized the depth required by a saw in close quarters. Building on their solution-based approach to products, the company has finally addressed the need for a truly portable full-power jobsite table saw. The Bosch GTS1031 table saw can be carried by its single handle, which is balanced in the middle, and all accessories are safely and securely stored on-board. This was demonstrated wonderfully by none other than Jason Feldner at the 2011 Bosch Media Event, who came running into the room with the Bosch GTS1031 table saw in one hand and a GTA500 stand in the other. Weighing in at a manageable 52 pounds, and this is one 15-amp jobsite table saw that does a great job of balancing portability and raw cutting power.
​If you decide to get a table saw with a one point five to two HP motor, then it’s going to operate at the standard household 120V circuit. When using a 2HP motor, you should expect it to draw between eighteen to twenty four amps. Also, keep in mind that in this case, the saw needs to be the only device that operates on a twenty amp circuit. The realistic limit of a one point five to 2 HP table saw is hardwood of up to two inches thick. If you need to cut thicker hardwood, then you’ll need a more powerful motor.
It has a machined aluminum table which is extremely precise. We like the Dewalt’s cast metal table for the price, but the company don’t list the material, and we suspect it’s not nearly as rugged as aluminum. The Bosch’s table is much better. It’s rugged, sturdy, and more consistently even than the Dewalt. The table makes this one a smarter choice for fine woodworkers or pros who need superior alignment.
The Bosch 4100-10 10 In. Worksite Table Saw with Gravity-Rise Wheeled Stand is a portable table saw with outstanding capacity and capability. The powerful 15-Amp saw delivers 4.0 max HP, with a large machined aluminum tabletop and a wide 25 In. ripping capacity. The Gravity-Rise Stand provides easy setup and take down. The SquareLock rip fence is engineered for trueness. The 4100 table saw also comes equipped with advanced electronics, such as soft start, constant response circuitry and overload protection.
While I appreciate this review, that Kobalt job site saw is the absolute worst. Uncontrollable blade wobble, terrible fence, trundle bolts that are nearly impossible to get to without tacking the back panel off (of course that doesn’t matter when the blade won’t stay in alignment for more than a day), miter slots that aren’t parallel to each other and also taper toward the backside of the table, and a riving knife without adequate adjustments to align it with the blade. Do not buy that piece of garbage.
Carrying things standing on end is easier, since it makes for a narrower package that can easily fit by your side. You’ll be able to lift a heavier saw less awkwardly in that position than if you were to carry it out in front of you. You’ll also want to think about size in terms of where you need to fit the saw in the vehicle, and where you’ll be storing it when it’s not in use.
We rotated the blade to the rear of the saw to enable the dial indicator to contact the same location of the same tooth behind the carbide portion. We positioned the dial indicator to the rear of the saw placed onto the blade and the reading recorded. If the blade and the miter slot were closer together at the rear of the saw, the dial indicator has a negative reading. If the blade and the miter slot were father apart at the rear of the saw, the dial indicator showed a positive reading.
Being concentrated is extremely important. A big percentage of injuries happen due to the lack of focus at any given moment. Remember, if anything happens, it will happen in under a second. Naturally, you won’t have any time to react properly. Music is something that can be dangerous and relaxing at the same time. Some people love working while listening to their favorite tracks, but it significantly lowers your concentration level. Therefore, you should avoid listening to music while operating a heavy-duty piece of equipment.
Home Depot sells around 60 models of table saws on its website, and the top models get hundreds of reviews from users. We found four portable saws with ratings of 4.5 stars or better from 250 users or more, and one contractor saw gets ratings just shy of 4.5 stars overall from more than 650 owners. Individual reviews are fairly short and include ratings for quality and value.
The latest advance in table saw safety is a feature that stops the spinning blade when it senses the presence of tissue, such as a finger or forearm. A company called SawStop was the first to offer this technology, and currently, it holds the exclusive right to sell saws with this feature in the United States. (Bosch introduced a portable table saw with blade-stopping technology in 2016, but was forced to take it off the market after a successful patent-infringement suit by SawStop.) In 2017, the CPSC proposed a new rule to make SawStop's technology mandatory on all table saws, but that rule is still under review. See the Buying Guide for more information.
We spent over 30 hours researching and testing 10 different brands of table saws and found that maximum speed, cord length, and cut depth were most important. The DEWALT DW7480 table saw scored high marks in every category and is our top pick. This 48 pound table saw is perfect for using at home or taking with you to the job site. It has a powerful 15 amp motor and 24” rip capacity that makes it a favorite with everyone. The 2 ½” dust collection port allowed us to connect the saw to a shop vac and reduce the amount of dust that was in the garage.
A lot of the modern table saws nowadays will have a dust collection port where you can hook up a vacuum or extraction system to it. We would always recommend that you purchase a table saw with a dust port, always check the size of the port to make sure it fits with either your vacuum or your extraction system, or you can always modify something to make them fit.
As you would expect, the most expensive saws made slightly smoother cuts. But the difference was negligible. The only saw that struggled to make smooth cuts in the super-thick oak was the Ryobi. In more common situations, like cutting 3/4-in.-thick material, Ryobi’s cut quality was fine. We found the blades included with all the saws to be adequate for most ripping tasks. But if you want cuts smooth enough for glue joints, you’ll have to invest in a better blade.
While you may be tempted to skip straight to the reviews, they are a bit on the technical side and contain plenty of terms you might not be familiar with just yet. My suggestion would be to start by reading the informational articles which will provide you with a decent amount of knowledge on table saws. After that, I sincerely doubt you would be caught off-guard while reading anything in the review section.
I can’t tell you how many times we’ve pulled out other jobsite saws only to have accessories fall off, or require off-tool storage. Bosch designed the GTS1031, however, to securely hold all of its accessories, even including the arbor wrenches (both of them) and an allen wrench for adjusting the riving knife and dust ejection points among other things. Our favorite was the rip fence, which simply flipped upside down and stored underneath the table – clever! About the most difficult adjustment was the riving knife, which is a tool-less maneuver, but one which requires you to stick your hand way into the blade cavity to reach the release lever. When making any adjustments to the blade, it goes without saying (but we’ll say it anyway) to disconnect power to the saw as a precaution.
×