The design is quite good. The SawStop safety system ensures smooth and flawless operation while protecting you from a variety of hazards. However, regardless of the safety aspects, you should always wear protective equipment, especially gloves and goggles. One of the most notable things about the design is the fact that it provides 99 percent dust collection both below and above the table. The riving knife maximizes kickback and also offers protection.

The Dewalt DWE7491is the clear choice for the full-time woodworking professional. It provides the widest rip capacity by far, it’s the fastest worker, and it has the best dust collection. The fence is a thing of beauty, and the secondary inner fence is a smart feature for smaller cuts. We think it’s worthy of any full-time woodworker, or DIYer with plenty of shop space and spending money.
If you’re a professional looking for a great table saw for the worksite, you’ll love the features and performance of the DEWALT DWE7480. Equipped with the Site-Pro Modular Guarding System has a rack and pinion telescoping fence rail that will allow you to make fast, smooth and accurate adjustments. This is the perfect table saw for cutting larger shelving and trim easily. With a 15 AMP 4800 rpm motor, you will go through all types of wood, even hardwood, with ease.

In order to measure the blade speed we used a digital laser non-contact tachometer. A piece of reflective tape was adhered to each saw blade just behind the carbide tooth, so that the tape would be just above the top of the wood cutting surface, allowing us to capture the blade speed during the cuts. We used a power-feeder to ensure that all the material was pushed through each saw at the same feed rate. In the photo above you can see our test set-up with the power feeder, a decibel meter to the left, the digital tachometer in the center, and the amp meter on the right. If you look really closely at the saw blade, the piece of reflective tape is to the left side of the blade near the power feeder.


All these saws have attached, collapsible stands with wheels that allow you to roll them around when they’re folded up. A few, like the DeWalt, Rockwell and Ryobi, can’t be wheeled around after they’re set up. But the biggest difference between stands is in how easy it is to set them up. The Ridgid and Bosch have nearly identical stands that work great and require you to only flip or depress one lever to unlock the stand. These are our favorites. The DeWalt stand is the sturdiest of the bunch and very intuitive. It sets up like a card table with legs that fold out and snap into place. The remaining candidates for best table saw have several different stand systems that aren’t quite as easy to set up but that work fine once you get the hang of them.

These smaller table saws, which come in a compact benchtop setup rather than with legs like a traditional table saw, are designed as portable job site saws. But they work just as well in a home workshop, and are ideal for shops that are tight on space. The Bosch and the DeWalt have many of their specs in common: Both include a 15 Amp motor, 10-inch blade, 3 1/8-inch depth of cut when the blade is set at 90 degrees and 2.2-inch depth of cut at 45 degrees. And safety features on both saws include a riving knife, anti-kickback pawls, blade guard and an included push stick. Features The GTS1031 is Bosch's newest table saw, designed for portability and intended to be light enough that you could carry it with one hand. Its rip fence is designed for quick and easy movement, and clamps into channels on opposite sides of the table to keep things consistently square without the need for frequent adjustment. Two notable advantages for the GTS1031: Its 5000 RPM max no-load speed compared to the 3850 RPM for the DeWalt, and the fact that you can use a 1/2-inch dado set with it (though it requires separate TS1013 dado throat insert).
I am looking to upgrade from my first table saw which is the Ryobi that you reviewed (had to find something cheap that was decent). I do a lot of rip cuts, as well as fine precision cuts for laminating and joinery required for frames, furniture, etc. I am looking at the Skilsaw and the Dewalt 7480 and cannot decide which would be best for me. Any insight would be helpful!
​If you decide to get a table saw with a one point five to two HP motor, then it’s going to operate at the standard household 120V circuit. When using a 2HP motor, you should expect it to draw between eighteen to twenty four amps. Also, keep in mind that in this case, the saw needs to be the only device that operates on a twenty amp circuit. The realistic limit of a one point five to 2 HP table saw is hardwood of up to two inches thick. If you need to cut thicker hardwood, then you’ll need a more powerful motor.
It has the widest rip capacity of the three. This one can handle materials up to 32 1/2”, which makes it ideal for folks who work with sheet stock on the go–especially when you consider the extra 22” you’ll have to the left of the blade. That’s thanks to the same rack and pinion fence as the smaller Dewalt. It’s even better on a larger scale, where the differences between this design and the sliding rail style you find on Bosch become very apparent. Reviewers agreed that this one felt much sturdier, smoother, and locked more securely than other portable units.

All seven saws in the best table saw testing have some kind of dust control. The Rockwell saw has a completely enclosed motor compartment with a large dust bag that attaches under the saw to catch sawdust. The remaining saws have a shroud around the blade and a 2-1/2-in. port on the back for attaching either a bag or a vacuum cleaner. None were perfect, but at least you can catch most of the sawdust. The Craftsman and Ryobi also include a dust bag that attaches to the vacuum cleaner port.
I definitely give this one 5 stars, but this is specific of the application – it being portable. If I was comparing it with other Hybrid saws, than this one doesn’t really compare when it comes to power. That being said. I was shopping for a table saw, after many years of working with a circular saw, and a straight edge – for me – it was time to get a setup for repetitive cuts that would be easier, and less time consuming (not to mention more precise, as the machine...

One of the principal causes of table saw accidents is kickback. This process happens when a piece of wood is ejected at great speed in the direction of the user. Binding between the blade and fence, the wood then gets trapped in the teeth and spat out. A splitter is a vertical blade that holds the kerf open to minimize the chance of kickback. 2 pawls are attached for this purpose.
Replacing the hugely popular outgoing W1824, the W1851 is a brand-new Shop Fox hybrid with the same enclosed cabinet as you’ll find on the W1819 alongside features more in line with a contractor’s saw. We chose to review the W1851 as it’s a more flexible option than the W1819 and appeals to a broader range of woodworkers. We rarely review brand new products but in this case we made an exception… With a brand like Shop Fox, it’s not a case of taking a chance but of betting on a winning team.
The throat plate is the removable piece surrounding the blade that sits flush with the table. Removing it gives you the ability to access the blade for removal or riving knife adjustments. The narrower the blade clearance the better for two reasons. First, it helps keep material from falling into the blade area or lodging between the blade and throat plate. Second, it gives you material support very close to the cut to help reduce tearout as the blade exits the cut.
Rockwell diverged from the crowd with this offering. For starters, the riving knife, anti-kickback pawls and blade guard are connected and remove as a unit. If you do remove them to make a non-through cut, you have to install the separate riving knife first. It’s not difficult, just different. This is the only saw with a right-tilting motor. We prefer left-tilting motors because it’s safer to make bevel cuts with the fence on the right side of the blade. There’s no port for attaching a vacuum cleaner, but there’s a large dust bag that does a good job of collecting sawdust. This saw cuts 3-9/16 in. at 90 degrees, 1/16 in. more than the next closest competitors, allowing you to rip a 4×4 in one pass. And like the Ryobi saw, it has a 30-in.-wide rip capacity.
This article is the place to start, and then you can take it from there. My table saw buying guide has all the essential information on table saws you will need, like their classification based on size, portability, motor type, blade size, and the features they come with. You will encounter each of these terms in all the product reviews, which is why you shouldn’t skip reading it.

The miter gauges on these saws range from downright flimsy to cabinet-saw quality. All the saws except the Craftsman and the DeWalt also have T-tracks—a nice feature that captures the miter gauge bar, making it easier to start wider crosscuts. Because the Ryobi and DeWalt saws don’t have a standard miter gauge slot, you can’t use accessories that require a 3/4-in. slot.

Included Components (1) Gravity Rise Table Stand, (1) 10 In. 40-Tooth Carbide-Tipped Saw Blade, (1) Standard Throat Plate Table Insert, (1) Smart Guard System, (1) Rip Fence, (1) Miter Gauge, (1) Push Stick, (1) Blade Wrench, (1) Hex Adjustment Wrench (1) table saw, (1) 24-tooth carbide saw blade, (1) rip fence, (1) miter gauge, (1) push stick, (2) blade-change wrenches SPT70WT 10-Inch Portable Worm Drive Table Saw, Rip Fence, Table Insert, Barrier Guard Assembly, Anti-Kickback Device, Miter Gauge, Push Stick, 10-Inch Carbide 24-Tooth Rip Cutting Blade, Blade Wrench, Hex Wrench, Manual bare-tool Bare-Tool Bare-Tool
It’s more compact than the Grizzly, and it uses its space efficiently. The Jet only has one extension table, but it makes the most of it. This one gets nearly the same rip capacity as the much larger Grizzly–to within 2 inches! There’s also a closed-off drawer in the bottom of the cabinet, which is ideal for storing all your smaller table saw accessories.
The Delta Unisaw is a heavyweight in woodworking circles. It’s been on the market for years, and it’s a stalwart through and through. It has a super-powerful 5 HP motor which can blast through the toughest hardwoods and composite materials quickly. It also features one of the most precise bevel adjustments on the market, down to 1/4 degrees! It has a solid, single-cast trunnion which provides excellent vibration dampening, and an extra-heavy case iron base. In short, this is a hulking beast of a machine, and it’s easy to see why it’s been a shop favorite for years.

Skilsaw produced the only worm drive table saw in our group and we had high expectations, especially given the high RPM count. In the end, the power is definitely at the professional level and settled in tied for fourth overall with DeWalt. This was the lightest, most compact saw in the group. Like DeWalt, the lack of an outer housing leads to more efficient cooling but drops storage for an extra blade.
These saws are the most difficult ones to categorize. The simplest explanation would be that they are somewhere in the middle between contractor and industrial cabinet saws. They are driven by an inboard belt motor. These units usually have open leg stands, but there are some models with closed ones – hence the whole confusion and difficulty in categorizing.
Whether your household’s resident handyman dabbles in amateur woodwork or takes pride in his DIY repair jobs, chances are he doesn’t need a high-end table saw to take care of his most basic needs. The Ryobi 15 Amp Table Saw is the ideal example of a machine that packs a load of must-have features you’d find in a higher-end table saw at a fraction of the price of competing models.

Our top midrange choice comes from Jet, which is a partner brand of the well-known Powermate lineup. This unit is a good choice for folks who need a saw that can cut through absolutely anything, at a reasonable price, and without taking up too much space. It’s more compact than the Grizzly, but it offers even faster saw speeds and more precise adjustments. We recommend it to folks who want lots of power, but don’t have the room for a larger cabinet unit.
However, with proper use, table saws are generally safe tools, advanced blade stopping technology not needed. Therefore considering a saw without such safety features is fine for the cautious DIY user or for the professional carpenter and/or builder. Take into careful account the actual table size of the table saw you are considering. If you are going to be completing rip cuts in large sheets of plywood, then you need a saw with a table large enough to support these big pieces of lumber.

If the blade you purchase has a .092” kerf (i.e. Irwin Marathon 80T, FreudLU83R010) you will most likely have issues with binding on the back end of the cut. To be safe, find a blade that has a kerf of around .098” (i.e. Freud Avanti TK905 50T) and this should take care of the problem. You should also take note that every blade Bosch makes should also work with the Bosch 4100-09.
Measuring 30.31" x 17.32" x 41.81", this powerhouse boasts a heavy duty 10" blade that can cut up to 4" x 4" of material in a single pass. For the handyman who likes to keep all of his tools within arm’s length, RIDGID’s table saw comes with convenient onboard storage so swapping out blades or accessing your tools is just a short reach away. Buyers are crazy for this table saw, and they report that it easily fits into the corner of their garages. Plus, quick and easy assembly means you can get to work straight out the gate.
All these saws have fences that extend to at least 24 in. to allow you to rip a 4 x 8-ft. sheet of plywood in half. And they all have a slightly different way of accomplishing this. DeWalt has the most straightforward method. You just push the fence out on its rails and flip over the board support. On the Rockwell saw, you flip out a hinged fence rail. The only drawback to this fence is that it must remain in the extended position for any cut, so it takes up quite a bit of room. The remaining saws require you to release one or two levers and pull out the fence extension.
There are a few nice conveniences which we don’t always see on affordable units like this. The Grizzly has a built-in miter guide, made from cast iron, which slides easily in the worktop. The left-tilting blade is coordinated with a digital display, which gives you an accurate, real-time readout on your bevel angle as you cut! The motor has a starting amperage of 13, which is safer for your breakers than 15 amp models. There’s a standard 4” dust collection port, and
With a cutting speed of at least 4,500 RPM, nothing will hold you back from getting the job done in minutes. Hitachi job site table saw is designed to give you freedom in your work and the ability to manage your time. Keep every minute accountable by investing in the right tools for your workshop. However, during different occasions, you will have different materials both in size and texture. During such moments, you will require adjusting the fence to accommodate your material and cutting style. This job site table saw is designed with an adjustable feature to ensure your precision and accuracy is not compromised. The low power consumption makes it easy for you to maintain the saw and enjoy smooth and accurate results at no extra cost. When it’s not in use, the table saw has fold and roll stand that guarantees you space saving and convenient storage. The foldable design also makes it easy to transport from one place to the other comfortably.
×