A table saw is a powerful tool that makes short work of even large pieces of lumber, allowing you to make rip cuts down the grain of boards, beams, and even entire sheets of plywood. No carpentry shop or professional construction site is complete without a table saw. Deciding which saw is best suited to a given home workshop, furniture production factory, or building site is an important decision and merits careful consideration.
You will need specialty blades for cutting materials such as plywood, masonry, hardwood and metals. Other specialty blades are used for dado cuts. Most dado sets have multiple rows of teeth and chippers and they are typically much wider than traditional blades. Be sure that the model of table saw you have can accommodate the type of specialty blades you want to get so you don’t waste your money on a blade that won’t fit.

The DeWalt will do you proud for a broad spread of applications. If you’re a home woodworker, you’ll be able to rip sheet material, size material as thick as 3 inches, frame lumber and make cross cuts to your heart’s content. For professionals, the DeWalt is perfect for trim carpentry, installation of hardwood floors, decking or remodeling. There’s very little you can’t do with this beast.
Safety is a prime concern for Bosch. From the SquareLock Rip Fence through to the patented SmartGuard System to lessen any chance of kickback, your security and comfort is taken care of. The blade guard and riving knife are quick-release. This takes away any excuse for not putting the guard back in place because it would be too much trouble, something that’s an accident waiting to happen.
Likes: Cuts extremely well and has excellent stability. Its blade guard and riving-knife assembly are locked and unlocked by a lever located conveniently along the table's left edge. A simple, separate shark-fin riving knife can be used when the guard is too big for narrow rip cuts. We appreciate the antiglare surface on the tape ruler that measures the distance from the blade to the fence.

If you're currently looking for a cabinet table saw and it's the first time you actually need to buy one, then you should know that they come in a wide range of types, from the larger contractor saws to the portable table saws that most people seem to own. However, buying the right model for you depends on your needs and how you're going to use it.
Install new blade- With the new blade, face the teeth of so they are pointing to the front of the saw table. Place the blade on the housing. Secure the new blade with the washer and nut with the use of a wrench. Make sure you are turning the wrench in a clockwise motion. Use the small piece of wood to secure the blade in place while you are securing it.
It’s often overwhelming when looking for new power tools and products online. So many features, specs and brands etc to research and review. So, what should you look for when buying a new table saw? One thing we always mention is to make sure you read as many table saw reviews as you can before purchasing one, this will insure you have the best table saw for your requirements.
For carpentry projects or as a starter saw, the DeWalt DW745 receives solid reviews. Though it doesn't have the capacity of the Bosch, owners say it's well made and easy to adjust. The rack-and-pinion fence earns kudos for accuracy. The saw weighs just 45 pounds and can even be hung on a workshop wall for storage; an optional is also available. The three-year warranty is another plus.
Speaking of safety, this particular model offers a satisfactory level of it. First of all, the tool-free adjustments come in handy if you’re in a middle of a project. In case you need to make a quick adjustment, you don’t have to stop whatever you’re doing and commit your attention to fine-tuning. Instead, you can do it on the go, without any additional tools. Furthermore, the convenient guarding system keeps your fingers and hands safe at all times. Don’t forget to wear protective gear; it can make a difference between life and death.
In terms of cutting results, Craftsman’s 28463 Jobsite Table Saw made a decent showing. It delivered accurate rip cuts, kept its bevel setting for angled ripping and could handle a stacked dado blade without laboring. Dust collection through an enclosed shroud was on par with more expensive machines. I also appreciated the saw’s clear, split guard and a riving knife system that is easy to install and adjust up or down. These are the plusses of what, in this test, is the budget-priced tool.
The Bosch 4100-09 offers many advanced features, making it a very capable table saw for woodworking. The air-filled wheels and gravity rising stand makes this table saw functional and lightweight. Set up and tear down of the table saw is a breeze. This technology allows the table saw to be moved from place to place, even over the most rough and challenging areas of the work site. The 4100-09 weighs 39 pounds, making it the perfect portable table saw. Although it is lightweight, it is very durable and stable.
I’m trying to replace some lost tools for a doctor inflicted, lawyer cowardice sustained injury. I’ve been a woodworker for more years than I might imagine I am comfortable with saying simply for it seems to have been bestowed upon me from birth. The only comment I have is a general comment. As I’ve noticed from about 20 years ago being introduced do officially being educated at a local community college, everyone there had prestige rights attached to it, a couple of cabinet makers I worked for did also that Porter Cable was the Cadilac of woodworking tools. Well, China… Read more »
For centuries, the job of the sawyer was, quite simply, to saw logs into lumber. Working in two-man teams, a pair of sawyers would use massive saws -- called whipsaws or pitsaws -- to cut felled trees into workable planks with their own muscles as the motive power. The job was exhausting and often dangerous, yet necessary to create the precious lumber used to build everything from homes to railroad bridges.

You can use these saw to cut plywood and other sheet goods, but their compact size makes this a challenge—and a potential safety hazard, if you don't have an extension table, rollers or a human partner to help support the wood on the infeed and outfeed sides. Stick with a circular saw for larger plywood rip cuts, but both of these saws can be workable backups (provided you don't need to rip widths of more than 16 or 18 inches.)
I am looking to upgrade from my first table saw which is the Ryobi that you reviewed (had to find something cheap that was decent). I do a lot of rip cuts, as well as fine precision cuts for laminating and joinery required for frames, furniture, etc. I am looking at the Skilsaw and the Dewalt 7480 and cannot decide which would be best for me. Any insight would be helpful!
When your skin contacts the blade even slightly, the charge transfers, and a switch flips on the motor, activating an instant brake. The aluminum brake swings into contact with the blade, stopping it instantly. The brake also propels the blade down through the arbor, so it retracts completely below your worktop. That means that other than the initial contact, you won’t touch the sharp edge at all.
In order to measure the blade speed we used a digital laser non-contact tachometer. A piece of reflective tape was adhered to each saw blade just behind the carbide tooth, so that the tape would be just above the top of the wood cutting surface, allowing us to capture the blade speed during the cuts. We used a power-feeder to ensure that all the material was pushed through each saw at the same feed rate. In the photo above you can see our test set-up with the power feeder, a decibel meter to the left, the digital tachometer in the center, and the amp meter on the right. If you look really closely at the saw blade, the piece of reflective tape is to the left side of the blade near the power feeder.
How do you tell what the best table saw is? With so many table saw choices on the market it’s hard to know which table saw is the best fit for you and your woodworking needs. Not for long. We’ve taken the leg work out by doing all the measuring, tracking, and researching for you. We’ve compiled year-over-year performance and pricing information for over 3 years to help you choose the table saw that is ideal for you and your project. Search no more, find your table saw below.
The first thing people notice about this unit is its design. The rolling stand is specially designed to mitigate the transport of this saw. In simpler words, whenever you need to move it, you can do it by simply rolling the unit on its wheels. One more notable thing is the 2-inch dust collector port. You can easily connect it to a vacuum and extract the dust efficiently and without much hassle.

Contractor saws are a perfect balance between functionality, manoeuvrability and price. These sorts of saws are perfect if you have bigger projects that you’re working on and will stay on site for a few months. This is due to the fact that they are a lot less portable, but that being said they are a great in-between saw as they still have great rip capacity and overall cutting power.
Robert Bosch Tool Corporation is aware of questions raised about the power of its REAXX™ Jobsite Table Saw. We are taking this feedback seriously and we’re working with product and engineering teams to answer these questions. Flesh-detecting Bosch Active Response Technology™, which comes on board every REAXX Job Site Table Saw, is unrelated to the questions raised about the saw. The REAXX table saw remains one of the safest and most-advanced table saws available today. 

If you’re a home DIYer, dust collection shouldn’t be a big worry. You can always hook the saw up to your shop vac, but if you’re only working with it occasionally, you’ll be fine to simply get your sawing done, and clear the exhaust port afterward. However, if you’re working on a professional jobsite, you should plan to collect at least most of the dust from your portable table saw via a vacuum system.

Table saws cut more or less the same way as a circular saw (covered in their own report): a round blade, usually 10 inches in diameter, spins as it works its way through the wood. The main difference is that the blade is fixed in place, sticking up through a gap in the table, and the operator moves the wood past the blade instead of moving the saw itself. Table saws support and guide lumber and wood panels as they pass over the spinning blade, making it easier to make accurate repeat cuts than with a circular saw.


DIY-ers love this type due to its simplistic yet effective operation. However, it’s not unusual for professionals to invest in these in order to avoid investing in cabinet models and save some money. Speaking of money, you should prepare yourself for a hefty investment if you opt for this particular type. However, most models are well-worth the money. These things last for years and don’t require a lot of maintenance apart from occasional blade replacements and minor adjustments.  They are not as easy to use as portable models, but you’ll learn how to use them in a matter of hours or days, as long as you follow the rules written in the user manual.
Safety and precision are usually at a high level. Some models even offer a sliding table as an option to mitigate cross-cutting. Needless to say, hobbyists love the sliding feature because it saves a lot of time and most importantly – nerves. As far as the driving mechanism goes, there are three possible options – single V-belt, serpentine belt, and a multiple V-belts.

TBB measured the accuracy of the factory-set 90 degree stop by using a Wixey WR365 digital inclinometer. This device has an accuracy of 0.1 degree. We placed the Wixey gauge on the table and calibrated the inclinometer to the table by zeroing out the gauge. After that calibration, the measurements give a result that is relative to the saw table. We moved the blade to an approximate position of 70 degrees off vertical. TBB attached the gauge to the blade and used the saw mechanism to adjust the blade incline to the point at which the blade or trunnion hit the factory-set 90 degree vertical stop and recorded the measurement. TBB ran the test twice to ensure the repeatability of the measurement. In every case, the result came out to within 0.1 degree of the prior test.
Both saws were almost equally quick to setup for use, with the DeWalt coming out slightly ahead. The throat plate, which is thicker and sturdier than Bosch's, is slightly easier to remove and reinsert. The DeWalt's blade cavity offers greater clearance, which makes locking down and loosening the riving knife easier without scraping a knuckle. Dewalt's riving knife adjustment required less wiggling and hunting to get it set properly.

We evaluated the flatness of the table by measuring the flatness by placing the edge of a precision ground flat bar across the table and placed feeler gauges in any gaps to measure any difference between the ground bar and the table. TBB took measurements in four directions. As the operator faces the saw, we measured the flatness at the arbor from front-to-rear; we measured the left-to right flatness at the arbor; we measured the flatness from the upper left-to-lower right table corners; and, finally, we measured the upper right-to-lower left flatness between the corners.


While I appreciate this review, that Kobalt job site saw is the absolute worst. Uncontrollable blade wobble, terrible fence, trundle bolts that are nearly impossible to get to without tacking the back panel off (of course that doesn’t matter when the blade won’t stay in alignment for more than a day), miter slots that aren’t parallel to each other and also taper toward the backside of the table, and a riving knife without adequate adjustments to align it with the blade. Do not buy that piece of garbage.

There’s a lot to like about this saw. The stand is easy to set up and very sturdy. We like the smooth-operating table extension and the blade guard’s hold-up feature and ease of installation. The only downside we found is that the motor mount is less rigid than those on the other saws we tested. We suspect that’s why the cut quality on our torture test was not as good with this saw.
The fact is, a table saw is designed to remove a large amount of material in a quick and efficient manner. With the volume of waste that is produced by any but the smallest table saws, a shop vacuum is not going to be up to the task. Short of purchasing a standalone dust collection system, the best that you can hope for from a shop vacuum is that it might keep some of the saw dust out of your eyes.
A 50 rpm deviation at those speeds is approximately 1% variance which is well within the tolerance we should expect from taking the readings at a precise instant of time. The meters were in constant motion and we took the reading off of a single video frame that represented our determination of no-load speeds. We report them as our instruments showed them. 1% is acceptable.
You’ll make most of your miter cuts on a miter saw. But when the material you’re cutting exceeds a miter saw’s cross-cutting capacity, you turn to your table saw miter gauge. These usually aren’t quite as precise, but some manufacturers put more thought and robustness into it than others. If you make a lot of long miter cuts, be sure to pay attention to this accessory.
We absolutely love the Dewalt DWE7491 that we recommended as our top quality choice above. It’s a powerful, precise workhorse that can handle nearly any cutting job. However, times are changing fast, and workplace safety standards are increasing just as rapidly. If you’re a professional who wants to stay on top of your code, you should consider getting a unit that’s equipped with a flesh-detections safety system.
In layman’s terms, a miter gauge is a device that allows users to set up the angle of the material being cut with a table saw. And while most table saws come with built-in miter gauges, others, well, don’t — which is why the Kreg KMS7102 Table Saw Precision Miter Gauge System is invaluable. Whether you’re replacing an old, worn-out gauge or putting it to use in conjunction with a table saw that didn’t come with its own proprietary gauge, the KMS7102 is specially designed with precision in mind. After all, accuracy is vital to successful woodwork.
I really do like your site and being on Long Island there is a familiarity to the way y’all work. You are quick to respond to comments and put in a great effort but…. This review I feel you miss the mark. Out of box accuracy is important but. Ore important to a pro user is tool able to be adjusted to be near perfect and how does it hold this position. No comments on how solid the fences are, ie deflection movement, ease of micro adjust, etc. all the fancy self feed stuff etc, what saw feels the most powerful? Smoothest ? All theses kizmos are for the manufacturers to hype. Your strengths are that you actually use these machines, so your strengths are to BE MORE opinionated or biased not less because your opinion has meaning or weight. Let the know knowings use the kizmos and just give us your real opinions based on real use. Just my 2 cents.
Look for guards with two independent panels on each side of the blade, so that while you work on one side, the other side keeps dust in the vacuum system, rather than flying off to the side. High-end cabinet units also have splitter and guard systems which are molded like the internal shrouding to amplify suction, so you should look carefully at those features.
The purchase of a table saw is no doubt a big investment. But there is a lot of flexibility in this class of tools to find one that fits in with your budget and your wants. Make sure to take into account how you will need to use the tool and where you will need to use it. Heavier models will be sturdier but they will also require more effort to load up when you need to.

It’s the safest of the three by a long, long shot. SawStop became a major brand thanks to a feature that they’ve named their brand after: an accident-proof stopping mechanism for the traditional table saw. The innovative brake system on this model is the best on the market at detecting flesh and stopping the blade immediately. It’s a sure bet for saving fingers or worse injuries in the workshop.


To get the feel of the cut, we used a two man team to feed from one end of the saw and catch on the other. This helped us reduce the friction that comes from one person trying to hold a board flush against the fence while also keeping downward pressure to keep it level on the table. There was definitely some hesitation at the beginning of each cut that was alleviated once the board was received by the second man on the other side. It was during this middle section that the table/fence friction was at its lowest point and we made our determinations about each saw’s power and cutting speed.
The saw itself is remarkably compact, measuring just 22.5″ square and a little over a foot in height (13″ to be more precise). With a steel “roll cage” that encloses the 4 HP 15-amp motor and a rubber handle that is positioned in the center of the right side of the saw, this is a tool that you’ll find very easy to toss into the back of a pickup or work van and take to any jobsite. When you carry it deck-inward, the weight of the saw presses in slightly against your leg – which actually steadies the saw somewhat, making it more manageable, though at 52-pounds let’s not go so far as to call this saw a breeze to carry. The Bosch GTS1031 included cord wrap, and the simple design of the frame also makes it easy to store up against a wall inside your shop when not in use. This isn’t a tool that really gets in the way much – it’s out of sight until it’s needed.

We recommend something with this technology for new woodworkers, instructors, or folks who work in a busy shop with lots of movement around them. They’re also a safe bet for buyers who simply like to take as many precautions as possible. The only downside to these systems is the price. You’ll find them on machines closer to the $3,000 mark, as a rule.


There’s a lot to like about this saw. The stand is easy to set up and very sturdy. We like the smooth-operating table extension and the blade guard’s hold-up feature and ease of installation. The only downside we found is that the motor mount is less rigid than those on the other saws we tested. We suspect that’s why the cut quality on our torture test was not as good with this saw.

Hello, Thank you for your comment. We apologize for any issues our Top Table Saws of 2018 blog post has caused. It was not written to be a comparative review of the different saws but a list of the top saws that we are currently selling. It would be unfair to compare performance of a portable jobsite table saw to a industrial cabinet saw and then also compare them on price. If you would like to read a very good comparative post we suggest you check out ProToolReviews.com. They are not tied to any manufacturers and have a very unbiased opinion.


If you need a table saw that can travel, the Bosch 4100-09 consistently earns high marks. Reviewers praise its power, accuracy, easy setup, and easy blade changes. They also love the gravity-rise wheeled stand, which rolls smoothly and snaps open or folds flat in a single lever-activated motion. Finally, they appreciate the convenience of the blade guard system, complete with riving knife and anti-kickback pawls.
The Shop Fox W1819 also comes with a miter fence with flip stop which provides excellent workpiece support and is great for longer workpieces. As for the flip stop, it’s going to be very useful especially when wanting to make several cuts of the same width. If you want to cut longer workpieces, you can also flip it out of the way and then pivot it back down in order to make more cuts at the cutting width of your choice.
As far as the durability goes, it’s great. The materials used in the production of various components are sturdy and also quite reliable. The accuracy is at a high level meaning you won’t have issues with the precision of this table saw, even if you’re an absolute beginner. On the other hand, make sure you make the necessary adjustments when you unbox the tool, before turning it on. If you don’t know how refer to the user manual, it’s comprehensive and well-written.

Plus, it’s simply a great table saw in its own right. It’s powerful, efficient, and quiet. It cuts through all kinds of stock smoothly and easily, and the dust collection system helps it clean up after itself. Previous buyers who upgraded to this one said that the transition from their old cabinet units felt like switching from a family sedan to a sports car. We recommend it to anyone looking for the absolute best quality, for small to midsize pro shop work or the passionate home woodworker.

Perhaps you realized, that you need a cabinet table saw instead? For this i would highly recommend the SawStop PCS31230-TGP236 3-HP (Read Reviews) which is the top choice if you are a safety conscious woodworker. Some of you have also asked me about makita. Well, They do offer good products, but sell stands seperately, that is the reason they were not included in this guide….but i’ll try to make up for it in 2018.
Our top midrange choice comes from Jet, which is a partner brand of the well-known Powermate lineup. This unit is a good choice for folks who need a saw that can cut through absolutely anything, at a reasonable price, and without taking up too much space. It’s more compact than the Grizzly, but it offers even faster saw speeds and more precise adjustments. We recommend it to folks who want lots of power, but don’t have the room for a larger cabinet unit.
Apart from some short reviews, we’ve also covered some other aspects such as safety and proper use of these tools. Make sure you thoroughly read our articles because they could save your life. The tips we offered are well-known among the professionals, but beginners are always susceptible to various risks, especially if they don’t know how to handle these tools properly.
We hear the term accuracy tossed around when it comes to finding the best portable jobsite table saw, but we really have to narrow down what that means. Every saw we tested has the capability of being calibrated and it should be the first thing you do after setting it up. Like a new miter saw, blade calibration is simply part of delivering professional results.
It’s more compact than the Grizzly, and it uses its space efficiently. The Jet only has one extension table, but it makes the most of it. This one gets nearly the same rip capacity as the much larger Grizzly–to within 2 inches! There’s also a closed-off drawer in the bottom of the cabinet, which is ideal for storing all your smaller table saw accessories.
Even though the trunnion mechanism from Powermatic has been known to be the best there is, further refinements have been made to it in order to make it even better. The conically shaped worm gear drive with better surface area, the high end bearings, but also the cast iron, box style construction combine with the solid and smooth feel of the height and tilt adjustments. Thanks to the adjustable backlash, it’s very easy for users to adjust the mechanism back to the factory fresh feel and clearances.
You’ll make most of your miter cuts on a miter saw. But when the material you’re cutting exceeds a miter saw’s cross-cutting capacity, you turn to your table saw miter gauge. These usually aren’t quite as precise, but some manufacturers put more thought and robustness into it than others. If you make a lot of long miter cuts, be sure to pay attention to this accessory.

Give yourself a reason to be proud of your job by bringing in a table saw that has what it takes to get quality cutting. Just as the name, Powermatic table saw will ensure your cutting is accurate and interesting. It has a poly-v belt, which maximizes motor efficiency and reduces vibration for noise-free performance. The table saw also features massive dust collection to ensure your working space is clean and accommodative. With 30” Accu-fence system, nothing will be impossible to handle. Additionally, the entire unit is designed with quality material for longevity. The design is also portable making it easy for you to move from one job site to the other comfortably.

×