The DeWalt DWE7499GD table saw earns a third place finish in the safety category thanks to their GuardDetect technology. This doesn’t prevent you from using the saw without the pawls and blade guard in place, but it does require you to physically indicate you are aware they’re not in place. Ideally, this gives your mind one last opportunity to consciously note the additional care that needs to take place before cutting.

The blade is a 24 tooth carbide tipped blade that is durable and long lasting. You can even adjust it to a 45 degree angle for those more difficult bevel cuts. If you’re working on uneven ground, you’ll love the rear feet that are fully adjustable so you can level you work space. You’ll get a lot of use out of the onboard storage that will give you easy access to the push stick and guarding components. Weighing only 45 pounds, you can move the table saw from work site to home with ease.

From there, the rest of the saws created a top tier of cutting power that wasn’t mind-blowingly better, but definitely noticeable. It took many cuts back and forth between saws to determine which came out ahead of other because they are so close to each other. Bosch’s REAXX took third place overall with SawStop ever so slightly ahead. Part of that simply came down to the fact that SawStop was a little bit smoother cutting. Coming out on top was Ridgid. There was noticeable vibration compared to Bosch and SawStop here, but it was able to muscle through each cut a little bit better than the other two.
I like the clever design of the stand on this saw which allows it to collapse or open by operating a single lever. The unit has two transport wheels which allows for easier relocation and the stand doubles as a pulling handle. It measures 39 x 30 x 20 inches which makes it pretty compact. The distance between the floor and the work surface is 37.5 inches. To make the stand as durable and corrosion-resistant as possible Bosch has given it a powder-coat finish.
While your table saw is unplugged, take the time to clear and clean the work surface, removing any debris that could negatively impact the smooth path of the wood you will be cutting. Then, lower or raise the blade to where the blade gullet (the curved section between each blade tooth) is equal with the top of the piece of wood to be cut. Also, make sure that your saw's dust exhaust port is clear and open and that a bag is in place to catch any excess sawdust.
It’s more compact than the Grizzly, and it uses its space efficiently. The Jet only has one extension table, but it makes the most of it. This one gets nearly the same rip capacity as the much larger Grizzly–to within 2 inches! There’s also a closed-off drawer in the bottom of the cabinet, which is ideal for storing all your smaller table saw accessories.

If you are an avid hobbyist, this saw is made just for you. The company is known for its uncompromising quality and durability. This saw has a safety system where the blade stops and retracts automatically when it comes into contact with anything that is not wood.  The microblade guards keep debris from flying all over your workshop. It is easy to change between blades. You will not require a riving knife to do this. Its award-winning dust collection system ensures that you have a clean and presentable workspace at the end of the day.
Pre-calibrated right out of the box, Kreg’s miter gauge is a blessing for the impatient among us. The folks at Kreg know their customers don’t want to waste time preparing their tools — they want to use them! That’s why the KMS7102 boasts positive stops at a variety of the most common angles: so you can begin using your brand new miter gauge straight away.
The Grizzly is our top choice for folks who need lots of room to work, plain and simple. Thanks to its dual extension tables, this one has the widest rip and fence capacity of the three units we’ve reviewed here. We also love that it makes full use of the space under the worktops, so you’ll get plenty of storage room to make up for its larger footprint.
The blade is a 24 tooth carbide tipped blade that is durable and long lasting. You can even adjust it to a 45 degree angle for those more difficult bevel cuts. If you’re working on uneven ground, you’ll love the rear feet that are fully adjustable so you can level you work space. You’ll get a lot of use out of the onboard storage that will give you easy access to the push stick and guarding components. Weighing only 45 pounds, you can move the table saw from work site to home with ease.
Kickback (if you didn’t already know) is one of the most common accidents with table saws. In order to prevent this you can make use of the riving knife (you may also find this referred to as a splitter). When the material gets pinched by the blade at a certain angle kickback occurs, but thanks to the riving knife there is no chance of this happening.
It’s built heavy. Like our other recommendations, this one has a machined cast iron worktop, and all-steel cabinet. There are miter slots cut into the worktop, and the bevel and height adjustments are via machined metal flywheels that are calibrated and balanced with the trunnion. We especially love the internal gearwork for raising the motor, which has precise torque bolts and a gas assist to make all your adjustments both smooth and easy. The cabinet is powdered steel for added durability, and the Professional woodworkers and amateur reviewers alike said they were above impressed with the overall build quality. This one feels as premium to use as you’d expect from the pricetag.
If you’re going to use your table saw every day, make sure you spend a bit more money for something of the heaviest build quality, with extended warranty coverage from a company with a great reputation for service. If you’re going to be using your cabinet unit only periodically, you probably don’t need to buy something premium. You’ll be able to get by with something around the $2,000, since you won’t be spending enough time cutting to really appreciate the design touches and tweaks that make the more expensive units more of a pleasure to use.
I can’t tell you how many times we’ve pulled out other jobsite saws only to have accessories fall off, or require off-tool storage. Bosch designed the GTS1031, however, to securely hold all of its accessories, even including the arbor wrenches (both of them) and an allen wrench for adjusting the riving knife and dust ejection points among other things. Our favorite was the rip fence, which simply flipped upside down and stored underneath the table – clever! About the most difficult adjustment was the riving knife, which is a tool-less maneuver, but one which requires you to stick your hand way into the blade cavity to reach the release lever. When making any adjustments to the blade, it goes without saying (but we’ll say it anyway) to disconnect power to the saw as a precaution.
home,page-template,page-template-full_width,page-template-full_width-php,page,page-id-4,mkd-core-1.0.2,ajax_fade,page_not_loaded,,table saw theme-child-ver-1.0.0,onyx-ver-1.4.1,vertical_menu_enabled, vertical_menu_left, vertical_menu_width_290,vertical_menu_background_opacity_over_slider vertical_menu_background_opacity_over_slider_on, vertical_menu_background_opacity,smooth_scroll,side_menu_slide_from_right,wpb-js-composer js-comp-ver-4.7.4,vc_responsive
But, their price point reflects that. If you want the absolute best table saw money can buy then you can go pay $10,000 and it’s yours. We always accept a certain number of tradeoffs depending on what our budget allows So, if I am only doing a few DIY projects a year, I am not a carpenter by trade, and my budget is limited, the SKIL table saw may be right up my alley.

We cannot emphasize enough how important it is to think about safety at all times while using these tools. Even the slightest mistake can make a difference between life and death. The worst part is the fact that it usually happens in an instant, leaving you no time to react at all. Therefore, whatever you do, don’t forget that there’s a thin line between you having ten fingers at one moment and 8 in the next second.
Makita joins DeWalt with an external riving knife release so you don’t have to reach into the throat to loosen it. We actually ran into an issue with the design because of a slightly bent plate holding the knife in place. That aside, the intent of the design is sound and should make for an an easier experience. Because of the external release, Makita screws down the throat plate in place. You should only need to get in there for blade changes if everything functions properly.
The CNS175-TGP36 SawStop is a 10 in. contractor table saw with a 45 degree bevel and a rip capacity of 36.5 in. Other than that, we think this is a pretty cool table saw for a few different reasons. First, the price is about half of all other SawStop table saws, and we know money talks (actually, it yells)! Second, like all other SawStop table saws, it has the integrated flesh sensing technology, so you can be sure you’re going to keep all your digits. Also, it has some pretty impressive power; it’s powered by 15 A motor so you’ll be able to tackle whatever you need. The last of our favorite features is its portability. For being a contractor saw, it’s pretty easy to pack up and move around.
If you’re a home DIYer or pro working mainly from a shop, you may have a wide table or countertop big enough to use the saw without any accessory stand. We would caution against working on sawhorses, though, as they can be wobbly and unsafe. It’s far better to spend a few extra dollars on a sturdy stand than to take risks with a rickety, improvised setup.
Skilsaw produced the only worm drive table saw in our group and we had high expectations, especially given the high RPM count. In the end, the power is definitely at the professional level and settled in tied for fourth overall with DeWalt. This was the lightest, most compact saw in the group. Like DeWalt, the lack of an outer housing leads to more efficient cooling but drops storage for an extra blade.
rarely have to work with stock that thick. I mostly prefer to do this on my bandsaw any way. The 2" dust port allows me to hook up the shop vac and it does a decent job of getting most of the dust. The saw doesn't have much room in front of the blade so it was impossible to use my shop made cutoff sled. I solved this problem by making my own removable infeed extension table. Now I can use the 22" cutoff sled. After a year and a half the saw is still in adjustment and runs true. The saw stays in my shop and doesn't get bounce around on the back of a pickup truck. Based on my experience I highly recommend this saw if you have a small shop and don't plan on building large pieces

Plus, it’s simply a great table saw in its own right. It’s powerful, efficient, and quiet. It cuts through all kinds of stock smoothly and easily, and the dust collection system helps it clean up after itself. Previous buyers who upgraded to this one said that the transition from their old cabinet units felt like switching from a family sedan to a sports car. We recommend it to anyone looking for the absolute best quality, for small to midsize pro shop work or the passionate home woodworker.
A riving knife is a piece of metal that comes included with your new saw. It’s shaped like a surfboard fin. Sadly, not all models come with this crucial part. If you purchase a model without it, make sure you design one for yourself as soon as possible. The construction of this piece is not a big deal at all; you can cut the shape in a matter of minutes and install it. Its purpose is to prevent the wood and debris from getting caught in the back of the blade which consequently kicks back thus jeopardizing your safety.
The table measures up at 29 inches by 21.5 inches. The 4100-09 is not suitable for dealing with large stock or sheets of wood. Made from aluminum, you’ll meet with no resistance as you slide the timber toward the blade. The only negative with the table is the way it’s finished with an anodized coating. This is fine to start with but tends to wear over time, something that doesn’t just look unsightly but can ultimately affect accuracy. This is a surprising oversight from Bosch and one we hope they rectify in future iterations of this fine table saw.
Methods for tilting the blade to cut bevels vary among the saws. The Porter-Cable saw is the only one with a conventional handwheel bevel control mounted on the side of the saw. The crank gives you great control for setting an exact angle. To set the bevel on the Bosch, DeWalt and Rockwell saws, you simply release the bevel-lock lever and tilt the saw to the preferred angle. It’s easy to go quickly from a 90-degree to a 45-degree bevel with this method. The Ridgid, Craftsman and Ryobi saws have a rack-and-pinion setup. These saws utilize the front crank for setting the bevel.

Dewalt has refined the DW745's design, most notably improving the blade guard and safety measures. What stands out about the DW745 is its rack-and-pinion rip fence that moves along telescoping rails at the front and rear of the table. This means that once the fence is set square, it should stay square. However, the DeWalt's maximum width for a rip cut is 16 inches, compared to 18 inches for the Bosch. But most users will make large rip cuts with a circular saw, so the 2-inch difference in capacity isn't a big deal.
While you may be tempted to skip straight to the reviews, they are a bit on the technical side and contain plenty of terms you might not be familiar with just yet. My suggestion would be to start by reading the informational articles which will provide you with a decent amount of knowledge on table saws. After that, I sincerely doubt you would be caught off-guard while reading anything in the review section.
Now, don’t get me wrong, there are other portable table saws that are lighter than Bosch’s GTS1031 (who’s name sounds like a cross between a fast production car and a tax document). The key with the Bosch is that it’s jobsite tough. Give the other saws some wet lumber or run them all day long and you’ll smoke the motor, bog them down, or send them off a second story porch in frustration. Bosch seems to have designed the GTS1031 with two things in mind: portability and power. Portability, because all of the accessories store right on-board, and they do so securely, so they won’t fall out, even if the saw is bumped and tossed around – as jobsite saws tend to be.
With a single cast iron trunnion system, the Delta UNISAW offers dependable accuracy, smooth and continuous operation, but also vibration free control. Thanks to the fact that it features a fifty-two inch fence system, it’s the perfect choice for woodworking pros, but also people who are just starting out in the woodworking industry, such as hobbyists. Since it also comes with an upfront bevel dial to easily fine tune the blade level, you get a striking accuracy within a quarter of a degree, ensuring precision setups cut after cut.

Disclosure: daringabroad.com blog is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Additionally, daringabroad.com participates in several other affiliate programs, and we sometimes get a commission through purchases made through our links.


One of the first things many Pros do is permanently (and intentionally) lose the blade guard and anti-kickback pawls. While they are a pain to install and store onboard, their ability to reduce the risk of injury is significant. Table saws are responsible for thousands of injuries every year and there are plenty of guys running around with stories of how they got injured. So practice installing them until it feels natural and then actually use them onsite.
The fact is, a table saw is designed to remove a large amount of material in a quick and efficient manner. With the volume of waste that is produced by any but the smallest table saws, a shop vacuum is not going to be up to the task. Short of purchasing a standalone dust collection system, the best that you can hope for from a shop vacuum is that it might keep some of the saw dust out of your eyes.
I like the clever design of the stand on this saw which allows it to collapse or open by operating a single lever. The unit has two transport wheels which allows for easier relocation and the stand doubles as a pulling handle. It measures 39 x 30 x 20 inches which makes it pretty compact. The distance between the floor and the work surface is 37.5 inches. To make the stand as durable and corrosion-resistant as possible Bosch has given it a powder-coat finish.
Another excellent choice for the hobbyist or at-home handyman, the SKIL 3410-02 10-Inch Table Saw is a great value, giving you a durable build and quality performance at a wallet-friendly price. It doesn’t have the same brand recognition as some of the more expensive options on this list, but reviewers love this machine and say that it’s perfect for woodworking and DIY projects.

I am a general contractor in the Midwest. I used the saw and stand a lot for the 1 week I've had it. Overall the saw works well, dado blades are easily interchangeable, and it's surprising quiet. However, the stand base bent on me today. I had it passively mounted in the rear of my enclosed 7x16 trailer. Opened the door this morning after arriving at the job site and it had sunken over. I thought maybe it had come out of the mount I made, but sadly that was not the case.


Give yourself a reason to be proud of your job by bringing in a table saw that has what it takes to get quality cutting. Just as the name, Powermatic table saw will ensure your cutting is accurate and interesting. It has a poly-v belt, which maximizes motor efficiency and reduces vibration for noise-free performance. The table saw also features massive dust collection to ensure your working space is clean and accommodative. With 30” Accu-fence system, nothing will be impossible to handle. Additionally, the entire unit is designed with quality material for longevity. The design is also portable making it easy for you to move from one job site to the other comfortably.
×