In recent years, there has been a cloud of controversy surrounding the inherent safety issues surrounding the table saw. SawStop developed a flesh detection technology that pulls the blade below the table surface 3 milliseconds after coming into contact with skin. It really created a new class of table saw that, as of June 1st, finally has some competition in the form of Bosch’s REAXX.
Electric brakes in the saw is an important feature as helps the saw in reversing electricity in the motor, thus contributing to a precise cut. It is highly recommended that when you are buying a saw choose the one with on and off switch. The switch should be easily accessible to make work better and more efficient. In addition, the switch should have a cover. This will keep you from accidentally turning the saw on and damaging your work area or cutting yourself.
Measuring approximately 22” x 38”, the contractor table saw is then next size up from the bench style. It typically sits on an open attached stand or base which may or may not be on wheels. It weighs between 200-300 pounds and is still portable but requires more than one person to lift. This style of table saw is good for woodworking shops, hobbyists, small contractors and DIYers. The 1-2 hp motors have enough power and stability to handle more heavy duty job site work and workshop demands. One of the benefits to these saws is that they still run on standard electrical circuits.
Dust capture from this saw is pretty bad. I was shocked that a European brand would ignore the dust collection to this extent – at least I was until I discovered that their version of the 4100 does have quite a few more pieces that help pull most of the dust from the airstream. There is a plate that encloses the rear around the vacuum port and a bottom grid that allow airflow to the motor while still shaping the airstream to drive the dust to the vac. I added the plate, but decided against the grid. Instead, I added a sheet of ¼” plywood and put a 4” vacuum port in it that I hook up to my dust collector. I also replaced the blade guard with the European version that has a dust port built in. Minor upgrades, but dust capture has gone from terrible/non-existent to pretty acceptable. Bosch also sell a bag that will capture whatever dust would get tossed out the back of the saw, but that isn’t much, so I consider it a waste. I did buy it, and it works well on other tools, but it is not IMO a must-have for the 4100
Just used this saw for the first time today and I love it. Instructions for putting the stand together were not very clear. There's a lot of very detailed reviews here, so there isn't much I can add that hasn't already been said; but one thing I didn't know until using it is that the rear legs are angled further back than the front ones to provide more stability when pushing stock through the saw. Only used it a few times today, but it was a pleasure to use.
After cutting a bunch of wood with this saw, we really liked the balance of power and portability of Bosch GTS1031 – and I think that’s what this saw is all about. For raw Performance, the unflappable motor-blade combo earned a stiff 8/10 in our tests, while its affordable $399 price tag put it at a solid 9/10 in our Value scale. Sure, you can get cheaper portable table saws, but you’ll find it a challenge to track down the combination of power and portability the Bosch GTS1031 offers. Bosch’s gravity rise-equipped 4100-09 remains a compelling alternative or those wanting an integrated stand. It occupies an additional 15″ in width and 8″ in length and is a full 3.5″ taller. But it only tacks on 8 pounds in weight. If you’re cutting larger pieces of wood or need a saw with a stand, the 4100-09 may be your baby, but the new Bosch GTS1031, with its “toss it in the truck” form factor is our new sweetheart tool. While it has an available GTA500 folding table stand accessory, the real advantage of this saw is it’s stand-free portability – so don’t make it into something it’s not. After using this tool, we think you’ll want to take it with you, as-is, just about everywhere!
The saw itself is remarkably compact, measuring just 22.5″ square and a little over a foot in height (13″ to be more precise). With a steel “roll cage” that encloses the 4 HP 15-amp motor and a rubber handle that is positioned in the center of the right side of the saw, this is a tool that you’ll find very easy to toss into the back of a pickup or work van and take to any jobsite. When you carry it deck-inward, the weight of the saw presses in slightly against your leg – which actually steadies the saw somewhat, making it more manageable, though at 52-pounds let’s not go so far as to call this saw a breeze to carry. The Bosch GTS1031 included cord wrap, and the simple design of the frame also makes it easy to store up against a wall inside your shop when not in use. This isn’t a tool that really gets in the way much – it’s out of sight until it’s needed.
The Grizzly is our top choice for folks who need lots of room to work, plain and simple. Thanks to its dual extension tables, this one has the widest rip and fence capacity of the three units we’ve reviewed here. We also love that it makes full use of the space under the worktops, so you’ll get plenty of storage room to make up for its larger footprint.
Plus, it’s simply a great table saw in its own right. It’s powerful, efficient, and quiet. It cuts through all kinds of stock smoothly and easily, and the dust collection system helps it clean up after itself. Previous buyers who upgraded to this one said that the transition from their old cabinet units felt like switching from a family sedan to a sports car. We recommend it to anyone looking for the absolute best quality, for small to midsize pro shop work or the passionate home woodworker.
Along with thinking about how the table saw will be used now, it is important to also consider how you will be using it in the future. Will your usage increase or decrease? Many woodworkers may turn a hobby into a fulltime profession if they are talented at what they do. Why are these considerations important? Because they will give you better insight into the kind of money you should spend on your table. If you are going to go into business for yourself in a year or two, spending the money for a high-quality table now is a good idea. It will save you from having to buy another table in the future to accommodate your new needs as a business rather than just a hobbyist.
The fact is, a table saw is designed to remove a large amount of material in a quick and efficient manner. With the volume of waste that is produced by any but the smallest table saws, a shop vacuum is not going to be up to the task. Short of purchasing a standalone dust collection system, the best that you can hope for from a shop vacuum is that it might keep some of the saw dust out of your eyes.

You’ll make most of your miter cuts on a miter saw. But when the material you’re cutting exceeds a miter saw’s cross-cutting capacity, you turn to your table saw miter gauge. These usually aren’t quite as precise, but some manufacturers put more thought and robustness into it than others. If you make a lot of long miter cuts, be sure to pay attention to this accessory.

But if you have the space for the DeWalt to sit upright at a work station or deep storage shelf, then it may be the better choice, thanks to its more comfortable adjustment controls. You won't be able to use a dado blade with the DeWalt (at least not safely), and the rip capacity is slightly smaller, but there's a reason why it's been popular for a while now. It's a great saw that delivers reliable performance.
It’s easy to use, quite safe, and most importantly – it’s a high-quality piece of equipment for a more than reasonable price. If you don’t like what you see, don’t hesitate to read some of our other reviews, there might be something of interest for you. As far as this particular model goes, it should turn out to be a worthy and cost-efficient investment. In the end, it all comes down to your personal preferences.
One thing manufactures noticed over the years was that when people used the splitters in normal straight cuts it worked well but it’s biggest downfall came when contractors wanted to do cross cuts. What would happen is that people would remove the splitters to make the cross cuts but then forget to fixed them back in place. One brilliant table saw safety feature is the riving knife. The Riving knife is attached directly to the blade mechanism, this allows it to always be attached not matter where or what angle the blade is.
You can opt to extend the warranty coverage to 3 years, all through an external provider. We actually prefer these third-party warranties for power tools because they allow you to deal with people who are on your side, as opposed to company representatives, who can be frustrating to say the least. We think add-on coverage is a great safeguard for any cabinet table saw, and it’s a very reasonable proposition on this model.

If you’re a DIY enthusiast, you’ll definitely find something of interest. On the other hand, professionals can also find good pieces of information on this page. The models we’ve covered all work as advertised, and you can rest assured that they are of high quality. The only thing you need to do is determine how much money you want to spend and which type is the best suiting one for your requirements.


As far as the durability goes, it’s great. The materials used in the production of various components are sturdy and also quite reliable. The accuracy is at a high level meaning you won’t have issues with the precision of this table saw, even if you’re an absolute beginner. On the other hand, make sure you make the necessary adjustments when you unbox the tool, before turning it on. If you don’t know how refer to the user manual, it’s comprehensive and well-written.
You can’t talk about the best portable jobsite table saw without talking about portability. Portability boils down to a couple of important features. First and foremost, weight has a huge impact on how easily you can transport the saw, especially if it has to go into the bed of a truck rather than a trailer. If you’ve got a trailer, then a wheeled stand becomes your best friend. We looked at both.
As far as the design goes, cabinet saws don’t look much different from the hybrid ones. However, when it comes to sheer power, this type is the most powerful one in every regard. Therefore, devoted professionals who work on massive heavy-duty projects usually prefer cabinet saws over anything else. Each element of a cabinet saw is constructed to withstand a lot of stress and pressure.

We spent a lot of time setting up and taking down the saws to see how well the stands worked and how easy it was to install and remove the blade guard and anti-kickback pawls. Then we ran a torturous ripping test with 3-in.-thick slabs of oak to find the best table saw. And finally, we used the saws for more conventional tasks like cutting plywood and ripping framing lumber as another test to determine the best table saw.


With that said, the Dewalt DWE7491RS (another jobsite saw) has an amazing fence. It also has a greater ripping capacity – so if this additional functionality is more important to you than portability, it might be something to consider. Although keep in mind that it’s also 30lbs heavier, and the stand is much worse than that of the Bosch (which we’ll discuss later in this article).
Hybrid table saws are the latest thing on the market these days. They’re in between contractor and cabinet table saws in terms of price, power, and precision. These have either half-cabinets or cutaway stands like a contractor saw, but with the super-powerful motor and improved stability of a cabinet unit. They’re heavy, so you should be prepared to use them on a wheeled lift, but they can be transported fairly easily if you have helpers.
The price is acceptable. One cannot say it’s a cheap piece of equipment because it’s not. But, the high quality of production and a great deal of precision justify the somewhat premium price. If you’re a devoted professional, the price shouldn’t be much of an issue for you. The only downside many people reported is the quality control within the company. Many models came with broken or missing parts.
Product reviews on this site contain our opinion of a product or service. We will always strive for objectivity and transparency in our reviews. Our goal is to provide readers with honest, objective information based on our own experiences. We never have and never will accept payment in exchange for a positive review. Many of the products that we review are provided to us for free by a manufacturer or retailer. In some cases, we also have advertising or affiliate relationships with manufacturers and retailers of products and services we review. For additional information please visit our additional disclosure policies.
It’s sturdy. This unit also has a metal roll cage frame all around, which helps it handle the rough and tumble of travelling to worksites on a regular basis. It has a locking mechanism to help it stay securely on stands. We’re also super impressed by how well-made the adjustment knobs feel on this one. Buyers reported using this one for several years with no issues.
Dewalt has refined the DW745's design, most notably improving the blade guard and safety measures. What stands out about the DW745 is its rack-and-pinion rip fence that moves along telescoping rails at the front and rear of the table. This means that once the fence is set square, it should stay square. However, the DeWalt's maximum width for a rip cut is 16 inches, compared to 18 inches for the Bosch. But most users will make large rip cuts with a circular saw, so the 2-inch difference in capacity isn't a big deal.
Make sure you know what’s covered and what’s not, especially if you’ll be using your machine commercially (many warranties are strictly for individual, not commercial use). It’s also a good choice in this case to purchase add-on warranty coverage from a third party at the checkout. We recommend these policies for most portable table saws, since most manufacturers have either very short warranty coverage, or longer warranties which require you to foot the bill for service calls or for returning the machine to the maker.
Electric brakes in the saw is an important feature as helps the saw in reversing electricity in the motor, thus contributing to a precise cut. It is highly recommended that when you are buying a saw choose the one with on and off switch. The switch should be easily accessible to make work better and more efficient. In addition, the switch should have a cover. This will keep you from accidentally turning the saw on and damaging your work area or cutting yourself.
The TruePower 01-0819 may look like a miniature version of a table saw — and that’s because it is! Ideal for hobbyist modelers and DIYers looking to tackle minor jobs, the 01-0819, while lacking the same power and performance as its larger, pricier counterparts, is a steal at under $50. A must for any toymaker’s workbench, this bite-sized machine measures in at 8.5" x 7" x 7", and while it lacks important parts like a guide fence, it gets basic 1/2" wood or foam board cutting jobs done, slicing through softer materials with ease.
One thing manufactures noticed over the years was that when people used the splitters in normal straight cuts it worked well but it’s biggest downfall came when contractors wanted to do cross cuts. What would happen is that people would remove the splitters to make the cross cuts but then forget to fixed them back in place. One brilliant table saw safety feature is the riving knife. The Riving knife is attached directly to the blade mechanism, this allows it to always be attached not matter where or what angle the blade is.

The stand strays from the idea that jobsite stands need to be wheeled. We can attribute this to its light weight. While it loses points for portability, Skilsaw’s design created the most stable stand of the entire group. Another benefit to going with this simple stand design is that it is certainly responsible for dropping the price point. Skilsaw is definitely the table saw you want to go with if you’re having to move your saw in and out of a truck bed rather than being able to wheel it up in a trailer.


Table saw flesh sensors are a brilliant and clever piece of engineering. Sawstop revolutionised the industry when they came up with this technology. Human skin is a good conductor of electricity where is wood isn’t. So, the system works by passing an electric current through the table saw blade its self and when it’s cutting wood it’s fine as there is no conductivity between the wood and the blade but as soon as it hits human skin and becomes conductive it triggers an electric brake that stops in the blade in only 0.02 seconds. You may end up with a small cut but at least you won’t lose your finger or worse. There are quite a few different versions now on the market so we would advise you to read plenty of table saw reviews and do you research into the different systems to find the best one for you.

Hybrid table saws are the latest thing on the market these days. They’re in between contractor and cabinet table saws in terms of price, power, and precision. These have either half-cabinets or cutaway stands like a contractor saw, but with the super-powerful motor and improved stability of a cabinet unit. They’re heavy, so you should be prepared to use them on a wheeled lift, but they can be transported fairly easily if you have helpers.
More expensive models also have more efficient drivetrains, which means they achieve a higher cutting speed for smoother, faster, and trouble-free cuts. Plus, their innovative belt designs and calibrated trunnion supports make the whole cutting experience smoother, quieter, and simpler. You’ll also pay extra for innovative safety features like skin detection, paddle power switches, magnetic switches, and thermal overload protection.
Bigger tables offer more potential for additional extensions. For example, if you’re planning to process a massive piece of wood but you cannot cut it in smaller pieces; a table extension will definitely come in handy. There are a lot of commercial add-ons you can choose from, but you can also construct one yourself if you’re experienced enough. Experimenting with these things never gets old or boring, but keep safety in mind at all times. Make sure it’s completely safe to use the said extension and pay special attention to the amount of vibrations and the overall integrity of the table after you’ve installed the add-on.
Service can be expensive on these models, so you should see if the company will be covering repairs, of if you’ll be expected to foot the bill. Add-on plans are a great way to minimize your liability if something goes wrong. By purchasing a third-party warranty, you can have a much better customer service experience. The warranty provider will deal with the company for you, so you don’t have to negotiate or deal with frustrating runarounds.
Along with thinking about how the table saw will be used now, it is important to also consider how you will be using it in the future. Will your usage increase or decrease? Many woodworkers may turn a hobby into a fulltime profession if they are talented at what they do. Why are these considerations important? Because they will give you better insight into the kind of money you should spend on your table. If you are going to go into business for yourself in a year or two, spending the money for a high-quality table now is a good idea. It will save you from having to buy another table in the future to accommodate your new needs as a business rather than just a hobbyist.
The design is not bad. The height of this particular table saw is around 35 inches. While some people don’t mind it, we think it could have been designed better. However, the best thing about the design is the fact that you can get both contractor and cabinet style table saws in one unit. Dust control is well-designed. The large 4-inch dust port offers a no-hassle setup, especially with vacuums of lower quality. In simpler words, you don’t need to purchase a super-expensive vacuum for this particular unit; any affordable one should do the job well.
×