You can’t talk about the best portable jobsite table saw without talking about portability. Portability boils down to a couple of important features. First and foremost, weight has a huge impact on how easily you can transport the saw, especially if it has to go into the bed of a truck rather than a trailer. If you’ve got a trailer, then a wheeled stand becomes your best friend. We looked at both.
From there, the rest of the saws created a top tier of cutting power that wasn’t mind-blowingly better, but definitely noticeable. It took many cuts back and forth between saws to determine which came out ahead of other because they are so close to each other. Bosch’s REAXX took third place overall with SawStop ever so slightly ahead. Part of that simply came down to the fact that SawStop was a little bit smoother cutting. Coming out on top was Ridgid. There was noticeable vibration compared to Bosch and SawStop here, but it was able to muscle through each cut a little bit better than the other two.
Todd Fratzel is the Editor of Tool Box Buzz and the President of Front Steps Media, LLC, a web based media company focused on the Home Improvement and Construction Industry.He is also the Principal Engineer for United Construction Corp., located in Newport, NH. In his capacity at United he oversees the Residential and Commercial Building Division along with all Design-Build projects.He is also the editor of Home Construction & Improvement.
Give yourself a reason to be proud of your job by bringing in a table saw that has what it takes to get quality cutting. Just as the name, Powermatic table saw will ensure your cutting is accurate and interesting. It has a poly-v belt, which maximizes motor efficiency and reduces vibration for noise-free performance. The table saw also features massive dust collection to ensure your working space is clean and accommodative. With 30” Accu-fence system, nothing will be impossible to handle. Additionally, the entire unit is designed with quality material for longevity. The design is also portable making it easy for you to move from one job site to the other comfortably.
We rotated the blade to the rear of the saw to enable the dial indicator to contact the same location of the same tooth behind the carbide portion. We positioned the dial indicator to the rear of the saw placed onto the blade and the reading recorded. If the blade and the miter slot were closer together at the rear of the saw, the dial indicator has a negative reading. If the blade and the miter slot were father apart at the rear of the saw, the dial indicator showed a positive reading.
This is a truly great saw, except that it is really tough to adjust the blade and rip fence for parallel. Once adjusted though, it is a fine piece of engineering. What I like best is that the saw is built for the job site. It is extremely beefy, but no too heavy. In my opinion, it strikes a nice balance. Its cart stand is the best in the industry, bar none. Once adjusted, the saw returns to its settings extremely well. It is obviously built for the long haul, and should last a contractor many years. I would definitely purchase this saw again. Now with the things that I wish were better. First, adjusting the blade for parallel is just plain hard. Mine was out from the factory by 4 thousandths. It is a trial and error process, and the instructions suck. Here's what to do: 1. Loosen the four screws indicated in the instructions. Starting from behind the saw, center the blade housing in the rear left to right as best you can, then tighten one screw not quite snug (you want the housing to rotate on this screw when you adjust the front). Next move to the front of the saw and loosen the lock lever for blade angle adjustment (the housing won't move unless you do). Now, begin experimenting with holding the housing at 90 degrees with one hand while sliding the housing back and forth with the other until square. When you think that you are close, lightly tighten one of the front housing screws. Check for parallel (look for videos on how to check a table saw blade for parallel), then tighten the blade angle adjustment lever. With these screws and the lever tight and locked, check again for parallel. If it is still good (I got it to 1/1000 inch of parallel), then lock all the screws and check one more time, if it's still good, then you are done with blade housing adjustment.
The DEWALT DW745 and the Bosch 4100 both have 15 amp motors, so power shouldn’t be a problem with either of these job site table saws. The DEWALT has a high torque motor that is capable of delivering a no-load speed of up to 3,850 rpm. The Bosch 15 amps and a no-load speed of up to 3,650 rpm. The difference between the two is not something that would be noticeable without sophisticated equipment, and will not affect performance in any significant manner. The noticeable difference between the two is that the Bosch 4100 comes equipped with a soft start motor that is lacking on the DEWALT DW745. This will cause a noticeable load on your power source, and may affect other tools and lighting attached to the same source during startup.
The body of the blade is made from hardened steel, helping to extend the lifespan and keep up with the tooth quality. The kerf is a crazy-thin 0.098 inch—narrow to keep the cuts fast by reducing the amount of material that needs to be removed. Like most Diablo blades, you’ll pay a bit of a premium up front, but the blade lasts so much longer than others on the market that the cost per cut is much lower.
The Grizzly is our top choice for folks who need lots of room to work, plain and simple. Thanks to its dual extension tables, this one has the widest rip and fence capacity of the three units we’ve reviewed here. We also love that it makes full use of the space under the worktops, so you’ll get plenty of storage room to make up for its larger footprint.
Sometimes picking a “Best Bet” is a real tossup, but not this time. While Bosch’s 4100-09 doesn’t disappoint, and DeWALT has what seems to be a bulletproof portable, I think RIDGID’s R4510 table saw really shines. Its sturdy workaday features, powerful motor and well-designed stand show that portability doesn’t have to mean compromise. This is an excellent woodworking choice for 10″ portable table saws.
Table saws cut more or less the same way as a circular saw (covered in their own report): a round blade, usually 10 inches in diameter, spins as it works its way through the wood. The main difference is that the blade is fixed in place, sticking up through a gap in the table, and the operator moves the wood past the blade instead of moving the saw itself. Table saws support and guide lumber and wood panels as they pass over the spinning blade, making it easier to make accurate repeat cuts than with a circular saw.
The machine has a more conventional rip fence/rail arrangement. The right half of the rail assembly folds out so the saw can achieve its full 30″ of rip capacity — wider than any other model here — but the fence would not slide smoothly over the rails without catching on the hinge joint. While the rip fence did maintain its locked settings, it lacks the heft and build quality of the competition.