Portable saws are usually light and smaller than the other types. The three basic types of portable saws are compact, bench top, and jobsite saws. Because they are designed for portability, the materials of which they are made sometimes lack sturdiness and stability. However, that’s not a reason to be alarmed; a vast majority of these units are absolutely safe for work.
The TruePower 01-0819 may look like a miniature version of a table saw — and that’s because it is! Ideal for hobbyist modelers and DIYers looking to tackle minor jobs, the 01-0819, while lacking the same power and performance as its larger, pricier counterparts, is a steal at under $50. A must for any toymaker’s workbench, this bite-sized machine measures in at 8.5" x 7" x 7", and while it lacks important parts like a guide fence, it gets basic 1/2" wood or foam board cutting jobs done, slicing through softer materials with ease.
Safety is a prime concern for Bosch. From the SquareLock Rip Fence through to the patented SmartGuard System to lessen any chance of kickback, your security and comfort is taken care of. The blade guard and riving knife are quick-release. This takes away any excuse for not putting the guard back in place because it would be too much trouble, something that’s an accident waiting to happen.
TBB used an iGauging 35-125-4 digital dial indicator to measure the accuracy of the blade position to the table miter slot. This instrument has an accuracy of .0005 inches. As part of the table saw set-up, TBB installed a new Diablo blade in each saw and these never-before-used blades were used in the measurement test. To ensure that any wobble in the blade did not enter into the test results, TBB marked a single tooth as the reference point for the measurement. The blade position was moved to the front of the saw to allow the iGauging dial indicator to hit the tooth immediately behind the carbide tooth, The iGauging dial indicator was calibrated and the indicator had a reading of zero.
Pre-calibrated right out of the box, Kreg’s miter gauge is a blessing for the impatient among us. The folks at Kreg know their customers don’t want to waste time preparing their tools — they want to use them! That’s why the KMS7102 boasts positive stops at a variety of the most common angles: so you can begin using your brand new miter gauge straight away.
We’re not alone in loving the Jet’s guard system. We read lots of reviews from pros who said they’d used lots of table saws in their time, but this was the first time they didn’t absolutely hate the guard. In fact, many wrote that they started working with the guard onboard for the first time, simply because it worked so well. It’s certainly one of the most unobtrusive ones we’ve seen!
If the blade you purchase has a .092” kerf (i.e. Irwin Marathon 80T, FreudLU83R010) you will most likely have issues with binding on the back end of the cut. To be safe, find a blade that has a kerf of around .098” (i.e. Freud Avanti TK905 50T) and this should take care of the problem. You should also take note that every blade Bosch makes should also work with the Bosch 4100-09.
It’s the best of the three at keeping your shop clean. The SawStop has a blade guard and arbor enclosure that’s engineered and sculpted to maximize vacuum suction at the cutting edge. Plus, the guard hugs tightly to the blade, and like the Jet, opens at each side so that whichever way you’re cutting, dust goes down the vacuum chute instead of off to the side of your workspace. It’s lab-tested to be up to 99% effective, and it’s certainly the most impressive dust collection system we’ve seen to date.
The first measurements we looked at with the performance testing was blade speed cutting all three of the test materials. This tests gives us a relative comparison of how much blade speed reduction the motors have under different loading conditions. In our opinion this gives us an idea of how strong the motor/gear box combination is for each saw. For each test we also recorded the “no-load” speed to capture the relative drop in rpm in the blade speed while cutting wood. We used our as-measured no-load speeds instead of the published values from the manufacturers.
Bosch GTS1031 10 in. portable jobsite table saw is powered by a 15 Amp motor that allows this table saw to rip through any lumber or hardwood quickly and easily. Bosch’s Smart Guard System provides added control while cutting, SquareLock Rip fence ensure consistent and accurate cuts, and an all steel base provides added durability. Oh yeah, and we forgot to mention the price. This is the most affordable table saw on our list!
The professional level saws saw a separation as well and all were well ahead of the cutting power we saw with the value group. A middle tier of cutting performance started with Makita and Bosch’s 4100 while DeWalt was significantly better. Entering the fray with the only worm drive system, we had high hopes for Skilsaw’s entry. It was solid and smooth—definitely at the Pro level— and close to what the 4100 delivered.
The Bosch is, in fact, almost twice as heavy its competitor. Despite its aluminum try! But…..there may be other things to consider when you think about the portability of a worksite table saw. One consideration is the ease of setting up and moving the saw table. The Bosch, with its unique Gravity-Rise Stand and solid rubber wheels, may be heavier but easier to move and set up for use. The DEWALT wouldn’t require as much muscle to move, but the table is relatively small and it has no wheels. It bears mentioning that its table is sold separately, and is assembled separately, whereas the Bosch unit’s Gravity-Rise Stand is a part of the overall unit. The stand allows the saw to be raised into working position in a single, fluid movement, and easily cuts set up time in half.
Safety and precision are usually at a high level. Some models even offer a sliding table as an option to mitigate cross-cutting. Needless to say, hobbyists love the sliding feature because it saves a lot of time and most importantly – nerves. As far as the driving mechanism goes, there are three possible options – single V-belt, serpentine belt, and a multiple V-belts.