Being concentrated is extremely important. A big percentage of injuries happen due to the lack of focus at any given moment. Remember, if anything happens, it will happen in under a second. Naturally, you won’t have any time to react properly. Music is something that can be dangerous and relaxing at the same time. Some people love working while listening to their favorite tracks, but it significantly lowers your concentration level. Therefore, you should avoid listening to music while operating a heavy-duty piece of equipment.
Now, don’t get me wrong, there are other portable table saws that are lighter than Bosch’s GTS1031 (who’s name sounds like a cross between a fast production car and a tax document). The key with the Bosch is that it’s jobsite tough. Give the other saws some wet lumber or run them all day long and you’ll smoke the motor, bog them down, or send them off a second story porch in frustration. Bosch seems to have designed the GTS1031 with two things in mind: portability and power. Portability, because all of the accessories store right on-board, and they do so securely, so they won’t fall out, even if the saw is bumped and tossed around – as jobsite saws tend to be.

Kobalt’s KT1015 Table Saw features value pricing with a decent rolling stand. We initially had questions about its dual-locking fence, but found that it actually worked quite well. There’s plenty of wobble in it, but if you follow our Pro Tip on adjustments in the fences section, you can lock the front end in square then stabilize it with the back lock.
I do not which is the best table saw, but I can tell you which is the worst. The rigid portable saw is a piece of garbage. I have purchased two in the last 4 years and the motor has failed in both, only to find that they do not sell a replacement motor. The Rigid customer service will not respond to any questions associated with the saw or replacement parts. I will not buy another Rigid tool and currently planning to try the Bosch table saw.
You will need specialty blades for cutting materials such as plywood, masonry, hardwood and metals. Other specialty blades are used for dado cuts. Most dado sets have multiple rows of teeth and chippers and they are typically much wider than traditional blades. Be sure that the model of table saw you have can accommodate the type of specialty blades you want to get so you don’t waste your money on a blade that won’t fit.

The first step to take when using a table saw is to don all the appropriate safety gear that a responsible operator should use. This includes, at the bare minimum, eye protection and thick work gloves. It's also a good idea to protect your ears with ear muffs or earplugs and to consider a mask that will cover your mouth and nose to prevent the inhalation of fine saw dust particles.
Just used this saw for the first time today and I love it. Instructions for putting the stand together were not very clear. There's a lot of very detailed reviews here, so there isn't much I can add that hasn't already been said; but one thing I didn't know until using it is that the rear legs are angled further back than the front ones to provide more stability when pushing stock through the saw. Only used it a few times today, but it was a pleasure to use.
After spending hours doing a lot of research and talking to professionals who use these tools on a regular basis we have put together a review for you that not only tells you three of the top table saws on the market today, but we tell you why they are popular and explain a bit about each so you have a good idea of what they are like. This table saw review will put much-needed information right at your fingertips so you can make a good decision on the right table saw for your needs.
IMPORTANT REVIEW UPDATE (10/4/2016): After doing some additional testing with pressure-treated lumber and heavier stock, we [initially] found some issues with the Bosch REAXX saw that we couldn’t explain—except to say that it didn’t have the power we expected for cutting through denser wood. The blade exhibited a significant drop in speed during many common ripping cuts, and it even stalled out entirely at other times. We contacted Bosch and worked directly with them to determine the nature of the issue (which appeared to have to do with the saw’s electronic speed control). Here is the initial statement from Bosch on the matter:
The more table size you have, the more support you have which is always a plus, not only for convenience but safety too. There are right side extensions that can be purchased for table saws that increase the table saw’s capacity to get to the center of a 4 x 8 sheet of wood. Although most saws have a rear band that supports the wood as it exits the saw, an additional safety measure is to rig up an outfeed support of some kind in addition to this rear bar. Be sure that the outfeed support you set up is ¼” lower than the table saw is.

It has the widest rip capacity of the three. This one can handle materials up to 32 1/2”, which makes it ideal for folks who work with sheet stock on the go–especially when you consider the extra 22” you’ll have to the left of the blade. That’s thanks to the same rack and pinion fence as the smaller Dewalt. It’s even better on a larger scale, where the differences between this design and the sliding rail style you find on Bosch become very apparent. Reviewers agreed that this one felt much sturdier, smoother, and locked more securely than other portable units.
Ridgid notches a third place finish as the only saw to include an independent blade height lock. The adjustment wheel raises and lowers with multiple full turns like most saws, but integrates a lock into the center. For the bevel adjustment, the outside of the height adjustment wheel turns a rack and pinion style system to accurately change the blade angle – a feature Makita shares.
The quiet, 220-volt motors in these saws cut through the hardest stock, hour after hour, without bogging down. Cabinets are metal and extend to the floor for the best dust collection. The tops are cast iron, wide, and stable, which makes it easy to cut sheet goods. The trunnions are cabinet-mounted, so you get minimal vibration and maximum accuracy. They're also heavy; some weigh over 600 pounds. Once a cabinet saw's in place, that's where it stays.

It’s the best of the three at keeping your shop clean. The SawStop has a blade guard and arbor enclosure that’s engineered and sculpted to maximize vacuum suction at the cutting edge. Plus, the guard hugs tightly to the blade, and like the Jet, opens at each side so that whichever way you’re cutting, dust goes down the vacuum chute instead of off to the side of your workspace. It’s lab-tested to be up to 99% effective, and it’s certainly the most impressive dust collection system we’ve seen to date.
One of the biggest perks of a cabinet table saw, aside from the rugged construction and wide worktop, is the sheer power of the tool. You should expect a cabinet table saw to cut absolutely any stock within its depth capacity smoothly and easily. Look for motors with at least 3 HP, and sophisticated belt drive systems which translate that grunt into 4000+ RPM blade speeds. Don’t accept lesser power ratings on a cabinet model: these are the gold standard of table saws for a reason!
SawStop PCS31230-TGP252 10 in. 3HP table saw is a high performance cabinet table saw that features a durable cast iron table, 44 x 27 in. of total space, and is super durable, making it an ideal table saw for professionals. In addition to its industrial capabilities, this SawStop table saw also boasts a couple other practical features including a Flesh Sensing Technology, dissipative arbor belt to prevent hazardous charges, and an easy-to-change brake cartridge.
Next, the rip fence is pretty hard to adjust also, and mine had a few thousandths of a bow, but that bow is way within industry standard for a portable saw. Here's what you do: First, check it for parallel, you might get lucky. (On a side note, there is a fine line between how tight to set the locking arm adjustment screw with this rip fence. Too tight, and when you lock it, you'll loose the self-adjustment feature, too loose isn't good either. Adjust the screw (on the rear of the fence), to where the fence self aligns while still getting tight) If you are like me, mine was 15 thousandths out, then unlock the locking handle and loosen the two screws on top closest to you in THIS ORDER! Loosen the screw closest to the lock handle first, and for a few turns. Next, loosen the screw that is about 6 inches away toward the middle just enough to where the fence will rotate on this screw, but not so much as to be sloppy. Begin experimenting. Pivot the fence back and forth, running your measuring device up and down the fence until you get pretty close. Lock handle and checking for parallel. Again and again. When you finally get pretty close to parallel, then lock the lever and experiment with locking both screws. If it doesn't move and you are within a few thousandths, then voila, you are done with adjusting the blade and rip fence for parallel. The other adjustments are straight forward, and once set up, THIS IS A GREAT SAW!!!!!!!!!!!!!! Good luck, hope this review helps
The table measures up at 29 inches by 21.5 inches. The 4100-09 is not suitable for dealing with large stock or sheets of wood. Made from aluminum, you’ll meet with no resistance as you slide the timber toward the blade. The only negative with the table is the way it’s finished with an anodized coating. This is fine to start with but tends to wear over time, something that doesn’t just look unsightly but can ultimately affect accuracy. This is a surprising oversight from Bosch and one we hope they rectify in future iterations of this fine table saw.
These table saws are all probably made in China where there’s apparently no meaningful out-going quality control. While the *average* quality from a given manufacturer might be great, you could also be unlucky get a piece of junk because *everything* made on the production line ships out. It’s a preferred business model these days – the prices are much cheaper but the manufacturers trade that off against dealing with significantly increased returns and the need for much more customer service.

Having only owned saws with cast iron tops this is a new experience for me. First let me note that the right side extension is not aluminum like the rest of the top. It is steel, painted to match. The entire top appears to be powder coated with a textured grey coating. No telling how durable it will be but it does allow wood to slide easily over it. Since the top is aluminum, it lets you know that by transferring all the motor noise and vibration throughout the saw. Not a big deal really but definitely different if you are used to the cast iron absorbing much of this on bigger saws.
×