Some buyers weren’t impressed with the blade adjustments. The knobs and trunnions are similar to those on the DW745, but some reviewers said their units felt a bit clunky on the way down. Again, due to the quality control issues on these models, it’s a good idea to do a very thorough inspection and test of your unit before it’s too late to return it.
One drawback is because of the way the blade is stopped, you will want to have an extra blade brake on hand because once it’s used, it cannot be reused. So, if you don’t have another handy, you will have some downtime. Also, the stopping of a blade moving at thousands of RPM can understandably be very hard on the blade itself. Often, the blade may need to be replaced after it has been stopped in this way. Still better than losing a thumb.
I’m not crazy about one feature, and it’s common to three of these five saws: to tip the blade, you unlock a lever behind the blade height hand wheel, then swing the undercarriage up to the angle you need before re-locking the lever. A geared bevel control would make this process a little easier. But, once tipped, Bosch held its angle setting well through my test cuts.
What 🤔?? I find it pretty rare to have to re-align the rack and pinion fence on the dewalt, but short of the first time figuring it out, it shouldn’t take more than 5-10 minutes to do. The time savings comes in not having to stick a tape to the fence every time you move it to ensure it’s parallel. I am excited to see other tool manufacturers are using rack and pinion fences now so that there are other options besides the dewalt, namely skil’s latest worm drive ts and the latest hitachi, I’m just not interested in any other fence system on a job site table saw.
We evaluated the flatness of the table by measuring the flatness by placing the edge of a precision ground flat bar across the table and placed feeler gauges in any gaps to measure any difference between the ground bar and the table. TBB took measurements in four directions. As the operator faces the saw, we measured the flatness at the arbor from front-to-rear; we measured the left-to right flatness at the arbor; we measured the flatness from the upper left-to-lower right table corners; and, finally, we measured the upper right-to-lower left flatness between the corners.
There are a few nice conveniences which we don’t always see on affordable units like this. The Grizzly has a built-in miter guide, made from cast iron, which slides easily in the worktop. The left-tilting blade is coordinated with a digital display, which gives you an accurate, real-time readout on your bevel angle as you cut! The motor has a starting amperage of 13, which is safer for your breakers than 15 amp models. There’s a standard 4” dust collection port, and
The Bosch 4100-09 offers many advanced features, making it a very capable table saw for woodworking. The air-filled wheels and gravity rising stand makes this table saw functional and lightweight. Set up and tear down of the table saw is a breeze. This technology allows the table saw to be moved from place to place, even over the most rough and challenging areas of the work site. The 4100-09 weighs 39 pounds, making it the perfect portable table saw. Although it is lightweight, it is very durable and stable.
The more table size you have, the more support you have which is always a plus, not only for convenience but safety too. There are right side extensions that can be purchased for table saws that increase the table saw’s capacity to get to the center of a 4 x 8 sheet of wood. Although most saws have a rear band that supports the wood as it exits the saw, an additional safety measure is to rig up an outfeed support of some kind in addition to this rear bar. Be sure that the outfeed support you set up is ¼” lower than the table saw is.
Powerful cutting and portable convenience with the Delta Powerful cutting and portable convenience with the Delta 36-6022. The 1-step release stand and large wheels make it easy to move the saw to any jobsite. The 15 Amp commercial grade motor cuts through the toughest materials. UL approved 3-way guarding system with riving knife for safety and excellent dust ... More + Product Details Close
This woodworking website has tons of information about how to use a table saw: choosing blades, cutting joints, safety features, and more. However, we found only five actual product reviews, none more recent than 2013. Although these individual reviews are hands-on, they don't put saws through any specific, detailed tests. There's also no direct comparison between saws and no formal rating system.
The miter gauges on these saws range from downright flimsy to cabinet-saw quality. All the saws except the Craftsman and the DeWalt also have T-tracks—a nice feature that captures the miter gauge bar, making it easier to start wider crosscuts. Because the Ryobi and DeWalt saws don’t have a standard miter gauge slot, you can’t use accessories that require a 3/4-in. slot.
As we said in the beginning of this section, many of these saws will be used, right out of the box, for rough cutting materials and the fine accuracy may not matter so much in that application. If this is the case for a saw, the quality of the cuts and more importantly, the potential safety of the operator is going to be a function of the as-shipped accuracy of the saw from the manufacturer. So, TBB wanted to see how the various saws compared right out of the box. The results are in and, as a group, these eight saws measured up quite well for out-of-the-box accuracy.