By the late 18th century, a new tool had been created that would eventually have the sawyers out of work: the circular saw. These early rotating saws were powered by a range of different forces, often including running water or wind, and sometimes driven by animal power. By the early 1800s, the sawmill was replacing the saw pit and its hardworking manual sawyers.
Reviewers recommend these models for easy transport to jobsites and for easy storage in a small workshop. Portable table saws come in two types. Benchtop saws sit on top of a workbench and are light enough to pick up and carry; jobsite saws are mounted on folding stands, usually with wheels for easier transport. The main drawbacks of a portable saw are its lower power and smaller table, which makes it tricky to cut larger lumber and sheet material such as plywood. Prices for portable saws start at less than $200, but the best-rated models typically cost $300 or more.

6. Clamp rip fence to check if it holds securely at front and rear. If rear is not clamped securely, un- clamp fence and turn rear clamp adjustment screw 6 clockwise for increased clamping. Try clamping the fence to verify if it self aligns and clamps tightly at the front and rear. Overtightening of the rear clamp adjustment screw 6 will cause the rip fence to be non-self aligning (Fig. 23). Overtightening may cause friction or “chatter” when fence is moved side to side.
The whole thing is a bit more versatile than the Dewalt, thanks to expanded fence rails and an extended trunnion set. It has a wider rip capacity than the Dewalt. This one uses a traditional sliding-rail fence which gives you a rip capacity up to 25 inches. The fence locks at either side, like the Dewalt’s. It also has a wider bevel range, tilting up to 47 degrees.

rarely have to work with stock that thick. I mostly prefer to do this on my bandsaw any way. The 2" dust port allows me to hook up the shop vac and it does a decent job of getting most of the dust. The saw doesn't have much room in front of the blade so it was impossible to use my shop made cutoff sled. I solved this problem by making my own removable infeed extension table. Now I can use the 22" cutoff sled. After a year and a half the saw is still in adjustment and runs true. The saw stays in my shop and doesn't get bounce around on the back of a pickup truck. Based on my experience I highly recommend this saw if you have a small shop and don't plan on building large pieces


Power protections are also a key safety feature, since they protect both your personal safety and the integrity of your table saw. Look for a magnetic switch in the power switch assembly of your saw. A magnetic switch protects the system from dangerous power fluctuations, and automatically shuts the machine off in case of a surge or drop in flow. It’ll also perform another valuable function when power goes out or a fuse flips: it’ll prevent the saw turning itself back on when power returns!
One of the principal causes of table saw accidents is kickback. This process happens when a piece of wood is ejected at great speed in the direction of the user. Binding between the blade and fence, the wood then gets trapped in the teeth and spat out. A splitter is a vertical blade that holds the kerf open to minimize the chance of kickback. 2 pawls are attached for this purpose.

It’s just as powerful as our other recommendations. The SawStop has a 3HP belt-driven motor, and like the Jet, it uses a tweaked multi-belt drive system to transfer maximum power from the drive shaft to the blade. That makes for as powerful a cabinet saw as any on the market. This one slices smoothly through anything you can feed into it. It also has a slightly thicker max cutting depth than our other recommendations, so it’s the better choice for sturdy stock.
Along with thinking about how the table saw will be used now, it is important to also consider how you will be using it in the future. Will your usage increase or decrease? Many woodworkers may turn a hobby into a fulltime profession if they are talented at what they do. Why are these considerations important? Because they will give you better insight into the kind of money you should spend on your table. If you are going to go into business for yourself in a year or two, spending the money for a high-quality table now is a good idea. It will save you from having to buy another table in the future to accommodate your new needs as a business rather than just a hobbyist.
It’s tough to be completely objective when choosing the best portable jobsite table saw since the stock blades vary so widely. Skilsaw comes with a 30-tooth Diablo blade and Makita’s stock 32-tooth blade are both excellent while others could use some help. To make this shootout about the saws and not the blades, we turned to Diablo to outfit each saw with the same accessory.

Some table saws go one better than a splitter. Splitters are fixed. They do not move along with the blade. It also needs to be removed if you’re making cross-cuts or dado cuts. A riving knife, on the other hand, is fixed to the same part as the blade. This means it can move along with the blade. Riving knives don’t get in the way either so this is the best option.
With a 32½" rip capacity and motor capable of up to 4800 rpm, the DWE7491RS is more than prepared to effectively deliver 3⅛" deep cuts to thick slabs of wood. Happy customers sing this machine’s praises, reporting that it’s as sturdy as a table saw can get — plus, it’s easy to use, and assembling it is a cinch. They do however note that workers looking to produce finer cuts should seek out a replacement blade since the one provided is more suited for fast, rough work.
×