Both saws were almost equally quick to setup for use, with the DeWalt coming out slightly ahead. The throat plate, which is thicker and sturdier than Bosch's, is slightly easier to remove and reinsert. The DeWalt's blade cavity offers greater clearance, which makes locking down and loosening the riving knife easier without scraping a knuckle. Dewalt's riving knife adjustment required less wiggling and hunting to get it set properly.


Our biggest surprise while running the best table saw review tests was in the cutting power and the quality of cut: There wasn’t much difference among them. All these saws ripped through 3-in.-thick oak without hesitating. We tried this test with the stock blades that came on the saws. Then we repeated the test using a top-quality blade in each saw.
The blades are the primary factor to consider when shopping for a saw as they hugely determine the performance of your table saw. The blades will only be effective if they are set at a correct depth of cut. The table saw will also perform best if only the correct blade for the cut is fitted, as a proper blade will enable you to achieve a precise and smooth cut. When purchasing a blade, go for the one with a correct setting blade. Consider the cutting depth also as this will determine its suitability for the job. You should also ensure that the table saw is equipped with splinter guard as this will help in minimizing splintering of the board’s top surface. Splinter guard also enhances accuracy because when it is lined up at the start and finish mark the saw will cut with precision. A suitable table saw should also have a 20mm arbor as this guarantees the stability of the blade and hence, safety in the workplace.
I’m not crazy about one feature, and it’s common to three of these five saws: to tip the blade, you unlock a lever behind the blade height hand wheel, then swing the undercarriage up to the angle you need before re-locking the lever. A geared bevel control would make this process a little easier. But, once tipped, Bosch held its angle setting well through my test cuts.
It has a lot of the same features we love on the Grizzly. The Jet has a cast iron worktop, a full cabinet enclosure, and a fence on rolling tracks along the edge of the table. It has a belt-driven 3HP motor, an electric brake with a magnetic switch, and precision-machined parts for exact cuts. There’s also an included miter gauge with a follow pin that runs in the T-slot on the saw’s worktop. All in all, it’s another complete package that ticks all our key boxes!

It has a lot of the same features we love on the Grizzly. The Jet has a cast iron worktop, a full cabinet enclosure, and a fence on rolling tracks along the edge of the table. It has a belt-driven 3HP motor, an electric brake with a magnetic switch, and precision-machined parts for exact cuts. There’s also an included miter gauge with a follow pin that runs in the T-slot on the saw’s worktop. All in all, it’s another complete package that ticks all our key boxes!
Like most other product review sites, ConsumerSearch is supported by a combination of commissions on the sale of the products we recommend and ads that are placed on our site by Google. If you find something you like, you can help support us by clicking through and buying the products we pick. Our editorial process is independent and unbiased; we don’t accept product samples, requests for reviews or product mentions, or direct advertising.
In addition, a top-quality fence should move smoothly and have a scale that’s accurate and easy to read. Our favorite is the DeWalt fence. The rack-and-pinion system keeps the fence parallel to the blade, and the micro-adjusting knob allows easy and precise fence positioning. Runners-up in this category for best table saw are the Ridgid and Bosch saws. They both have superb fences, with the added advantage of T-slots for attaching accessories like featherboards.
In the commercial construction business, we typically buy a job site saw for each project and use it up during the course of an 18-month job. When these saws hit the site, they are unboxed, assembled and immediately put into use. We rip stacks and stacks of sheet goods with these saws and the tolerances of the cut materials are not very critical. However, that example represents the portable saw use within our commercial crews’ business.
Welcome to the heart of this website – my selection of the best table saws for several specific needs. You see, it’s impossible to select only ONE as the best for all purposes because a table saw should be carefully tailored to your needs. There’s no point in buying a complex cabinet saw if you’re a beginner, you’re probably better off with a solid benchtop saw. The same goes if you’re a professional, only the other way around.
Under the table, you’ll find plenty of space to store away your accessories. This is valuable if you’re working on site and don’t want to keep hunting down bits and pieces. You’ll be able to stash your arbor wrench and Allen wrenches close to hand. The rip fence also flips upside down and can be stored under the table. It’s this kind of attention to detail for a jobsite saw that’s always appreciated.
The machine has a more conventional rip fence/rail arrangement. The right half of the rail assembly folds out so the saw can achieve its full 30″ of rip capacity — wider than any other model here — but the fence would not slide smoothly over the rails without catching on the hinge joint. While the rip fence did maintain its locked settings, it lacks the heft and build quality of the competition.
Rockwell diverged from the crowd with this offering. For starters, the riving knife, anti-kickback pawls and blade guard are connected and remove as a unit. If you do remove them to make a non-through cut, you have to install the separate riving knife first. It’s not difficult, just different. This is the only saw with a right-tilting motor. We prefer left-tilting motors because it’s safer to make bevel cuts with the fence on the right side of the blade. There’s no port for attaching a vacuum cleaner, but there’s a large dust bag that does a good job of collecting sawdust. This saw cuts 3-9/16 in. at 90 degrees, 1/16 in. more than the next closest competitors, allowing you to rip a 4×4 in one pass. And like the Ryobi saw, it has a 30-in.-wide rip capacity.
You have to know the amount of money you are willing to spend for the right saw. The truth is that the price will vary significantly depending on where you are buying the saw, the brand and the features it comes with. However, with a good budget, you can easily narrow down the options you may have. You will have a smaller range to work with and you will know what features to expect within that price range. Always be willing to spend a little more on the table saw you want in your workshop especially if you work on wood every day.
×