You can’t talk about the best portable jobsite table saw without talking about portability. Portability boils down to a couple of important features. First and foremost, weight has a huge impact on how easily you can transport the saw, especially if it has to go into the bed of a truck rather than a trailer. If you’ve got a trailer, then a wheeled stand becomes your best friend. We looked at both.

What if a contractor uses their job site saw for high quality built-ins or high tolerance finished cuts? In that case, saw accuracy is critical for that work. In this use case, if the saw is immediately put into use, success depends upon the out-of-the-box accuracy from the manufacturer. The quality of the cuts and more importantly the potential safety of the operator is going to be a function of the as-shipped accuracy of the saw from the manufacturer.
Table saws can pose a serious risk of injury, since part of the spinning blade comes up above the surface of the table where it can come into contact with the user's hand as it guides the wood. Thanks to voluntary safety standards introduced by Underwriters Laboratories (UL) in 2007, pretty much all table saws now come with blade guards that minimize the risk. Modern guard systems are easier to remove and replace as needed – an important feature because inconvenient blade guards are apt to be left off the saw.

The DeWalt will do you proud for a broad spread of applications. If you’re a home woodworker, you’ll be able to rip sheet material, size material as thick as 3 inches, frame lumber and make cross cuts to your heart’s content. For professionals, the DeWalt is perfect for trim carpentry, installation of hardwood floors, decking or remodeling. There’s very little you can’t do with this beast.
The Grizzly, like the other cabinet models you’ll see here, requires a 220V power supply. If you’re a professional woodworker, you probably already have a 220V hookup. If you’re a home woodworker or DIYer, you’ll need to have one installed, if you haven’t already. It can be an expensive installation, so factor in the cost when you consider how much you’ll spend on your new saw.
Previous buyers said they were at a loss to find materials that the Jet couldn’t cut! They said it went like butter, with no lag whatsoever, and almost no vibration at all. Reviewers raved about the motor’s power, and especially complimented how steadily it ran. This is an excellent choice for hardwoods, thick softwoods, and composite boards: absolutely anything that’ll fit.
rarely have to work with stock that thick. I mostly prefer to do this on my bandsaw any way. The 2" dust port allows me to hook up the shop vac and it does a decent job of getting most of the dust. The saw doesn't have much room in front of the blade so it was impossible to use my shop made cutoff sled. I solved this problem by making my own removable infeed extension table. Now I can use the 22" cutoff sled. After a year and a half the saw is still in adjustment and runs true. The saw stays in my shop and doesn't get bounce around on the back of a pickup truck. Based on my experience I highly recommend this saw if you have a small shop and don't plan on building large pieces
Table saws cut more or less the same way as a circular saw (covered in their own report): a round blade, usually 10 inches in diameter, spins as it works its way through the wood. The main difference is that the blade is fixed in place, sticking up through a gap in the table, and the operator moves the wood past the blade instead of moving the saw itself. Table saws support and guide lumber and wood panels as they pass over the spinning blade, making it easier to make accurate repeat cuts than with a circular saw.

As for various accessories and attachments such as rip, miter and blade guard, these can be stored in their own specially designed hangars. If you plan on using other blades (and you probably will) there is also a well where you can store all the blades you have. In order to keep the surface of the table dust-free there is a dust collection port featuring a shrouded design which can be attached to the vacuum.


In our introduction and how-to sections, we’ve talked about some of the key reasons to buy a cabinet-style model. These are the most stable table saws you can find. They produce the smoothest, cleanest cuts. They’re also tools that are built to last a lifetime. We recommend them to any professional with the shop space to install one. They’re also the ultimate choice to ardent hobbyists with plenty of room to spare and an ample budget.

I knew there were jobsite table saws on the market for less than $250, but I never thought they were good enough to get my recommendation. Sure, the SKIL 3410-02 is not a professional saw and may not be versatile enough for contractors, but the stand, power, accuracy and build quality of this table saw are much better than I thought possible in this class.
For ideal usage, the on/off switch needs to be mounted on the front of the saw and should be easy to turn off with your knee or a swat without having to look at it to locate it. Most table saw models have a safety feature that is a plastic key that has to be inserted before the table saw can be turned on. Some may even have a way to padlock the switch.
rarely have to work with stock that thick. I mostly prefer to do this on my bandsaw any way. The 2" dust port allows me to hook up the shop vac and it does a decent job of getting most of the dust. The saw doesn't have much room in front of the blade so it was impossible to use my shop made cutoff sled. I solved this problem by making my own removable infeed extension table. Now I can use the 22" cutoff sled. After a year and a half the saw is still in adjustment and runs true. The saw stays in my shop and doesn't get bounce around on the back of a pickup truck. Based on my experience I highly recommend this saw if you have a small shop and don't plan on building large pieces
All table saws sold in the U.S. come with a riving knife, anti-kickback pawls, and a split blade guard. Because some cuts can’t be made with these safety features installed, they are removable. If you’re looking for a fun party game, see who of your uninitiated friends can install both correctly without a manual. While each one is different, their nature means you can use the saw without them installed. I’d be remiss if I didn’t tell you those cuts are more dangerous, so avoid it if you can.
All these saws have attached, collapsible stands with wheels that allow you to roll them around when they’re folded up. A few, like the DeWalt, Rockwell and Ryobi, can’t be wheeled around after they’re set up. But the biggest difference between stands is in how easy it is to set them up. The Ridgid and Bosch have nearly identical stands that work great and require you to only flip or depress one lever to unlock the stand. These are our favorites. The DeWalt stand is the sturdiest of the bunch and very intuitive. It sets up like a card table with legs that fold out and snap into place. The remaining candidates for best table saw have several different stand systems that aren’t quite as easy to set up but that work fine once you get the hang of them.
The DCS7485T1 60-Volt MAX 8-1/4 in. table saw The DCS7485T1 60-Volt MAX 8-1/4 in. table saw is maximized for accuracy capacity and runtime. The brushless motor delivers the power to cut all common materials the rack and pinion fence allows for fast easy adjustments and provides the capacity to rip 4x8 sheet goods. The DCS7485T1 comes with 1 ...  More + Product Details Close
Both of these table saws have a port that connects to a shop vacuum for dust collection. The DEWALT features a 2.5” port, while the Bosch has a 2” port. However, neither seems to do all that great a job. The Bosch might fare a little worse as far as the dust port clogging, but the DEWALT has some problems in this area, too. The Bosch is said to spew sawdust on the floor as though there was no dust collection port at all. The DEWALT racks up some complaints about the same problem.
Move the wood to and then "through" the spinning saw blade slowly and steadily. It's alright to use your hands while you're still at least a foot or so from the blade, but once the end of the board or sheet nears the blade, you should use a pushing stick to keep the wood moving and to keep your fingers away from the blade. Even an experienced carpenter can have a lapse in concentration or a slip that can lead to serious injury.
It can seem like plastic is a weight-saver on the part of the manufacturer, but it’s really a cost-saver. You shouldn’t accept shoddy build quality in the name of getting a lighter machine. While no portable unit will include heavy cast iron components like a cabinet table saw, you can find metal alternatives that offer rugged, long-lasting build quality. Instead of plastic, look for aluminum.

I’m no stranger to Bosch’s 4100-09 saw with Gravity-Rise™ stand. I’ve used one several times to build projects for this magazine, including the Serving Tray Cart that appeared in the June issue. So, I was not surprised when it tested impressively here. Rip cuts were on the mark, thanks to a rugged, beefy fence that stayed parallel to the blade each time I reset it. A flip of a red lever underneath unlocks the rails so they slide out and extend ripping capacity up to 25″.

The Skilsaw SPT70WT-01 is a super high quality table saw with the power to match. The Diablo blade that comes with it will cut through 4×4 without any problems at all, like a knife through butter! One of the best features we noted was the fact that there is barely any vibration, this allows to you to cut as straight as an arrow, you can really feel the build quality with this saw.It has an extremely easy to use miter gauge, just a flick of the wrist to change the angle of cuts to exactly what you want.
With that said, the Dewalt DWE7491RS (another jobsite saw) has an amazing fence. It also has a greater ripping capacity – so if this additional functionality is more important to you than portability, it might be something to consider. Although keep in mind that it’s also 30lbs heavier, and the stand is much worse than that of the Bosch (which we’ll discuss later in this article).
If you are making a cut that will require your hands to get close to the blade, (within 6 inches) use a push stick or two to eliminate the chances of your hand touching the blade. If this is a big concern for you, maybe consider a saw that uses flesh detection to stop the blade. The additional cost of the saw will be instantly appreciated the first time you need it.
The advent of ever better motive power that came with 19th century developments led to ever more efficient and ever more compact power saws. The first recognizably modern table saws date to the latter decades of that century. With compact and powerful electric motors developed and refined throughout the 20th century, tables saws were widely available and were both compact enough for home use, yet powerful enough for nearly any lumber ripping task.
Make sure all the panels on the cabinet (including the motor shroud) are made from steel, and look for powder-coating on the panels to help the paintwork last. The adjustment flywheels, the fence rails, and the frame of the table assembly should be steel as well. The most important part to look at under the hood is the trunnion. The trunnion supports the motor, and you’ll want it to be made from solid cast iron. The sturdier the trunnion, the smoother your unit will cut.
A gauge will allow you to make very detailed cross and angled cuts. This is a bit of kit that you need to research in great depth as it can make or break the accuracy of your cuts and angles. With a good gauge, you can check blade height, blade angles, miter angles and much more. For further reading checkout Wikipedia’s table saw page and for in-depth air compressor reviews.
The whole thing is a bit more versatile than the Dewalt, thanks to expanded fence rails and an extended trunnion set. It has a wider rip capacity than the Dewalt. This one uses a traditional sliding-rail fence which gives you a rip capacity up to 25 inches. The fence locks at either side, like the Dewalt’s. It also has a wider bevel range, tilting up to 47 degrees.

If you work with wood in any capacity, chances are you rely on a table saw to make clean, accurate cuts. But when your good old saw goes to the big toolshed in the sky, it’s time to opt for a replacement. Before you dish out your hard-earned money on the first model you come across, remember that a table saw is a big investment, so it’s in your best interest to look into the many technical specifications of each option before you settle on a final purchase.


I like the clever design of the stand on this saw which allows it to collapse or open by operating a single lever. The unit has two transport wheels which allows for easier relocation and the stand doubles as a pulling handle. It measures 39 x 30 x 20 inches which makes it pretty compact. The distance between the floor and the work surface is 37.5 inches. To make the stand as durable and corrosion-resistant as possible Bosch has given it a powder-coat finish.

But, their price point reflects that. If you want the absolute best table saw money can buy then you can go pay $10,000 and it’s yours. We always accept a certain number of tradeoffs depending on what our budget allows So, if I am only doing a few DIY projects a year, I am not a carpenter by trade, and my budget is limited, the SKIL table saw may be right up my alley.
Welcome to the heart of this website – my selection of the best table saws for several specific needs. You see, it’s impossible to select only ONE as the best for all purposes because a table saw should be carefully tailored to your needs. There’s no point in buying a complex cabinet saw if you’re a beginner, you’re probably better off with a solid benchtop saw. The same goes if you’re a professional, only the other way around.
post-template-default,single,single-post,postid-5859,single-format-standard,mkd-core-1.0.2,ajax_fade,page_not_loaded,,table saw theme-child-ver-1.0.0,onyx-ver-1.4.1,vertical_menu_enabled, vertical_menu_left, vertical_menu_width_290,vertical_menu_background_opacity_over_slider vertical_menu_background_opacity_over_slider_on,smooth_scroll,side_menu_slide_from_right,wpb-js-composer js-comp-ver-4.7.4,vc_responsive
We took all of the data from the RPM and AMP measurements and added them to come up with the final performance rankings. For each saw we added up the total percentage decrease in RPM’s (for each material type) and added that to the total percentage increase in AMP’s (for each material type). This gives us a relative comparison of each saw over all 6 sets of data.

Prices, promotions, styles, and availability may vary. Our local stores do not honor online pricing. Prices and availability of products and services are subject to change without notice. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted.

In terms of cutting results, Craftsman’s 28463 Jobsite Table Saw made a decent showing. It delivered accurate rip cuts, kept its bevel setting for angled ripping and could handle a stacked dado blade without laboring. Dust collection through an enclosed shroud was on par with more expensive machines. I also appreciated the saw’s clear, split guard and a riving knife system that is easy to install and adjust up or down. These are the plusses of what, in this test, is the budget-priced tool.


I can’t tell you how many times we’ve pulled out other jobsite saws only to have accessories fall off, or require off-tool storage. Bosch designed the GTS1031, however, to securely hold all of its accessories, even including the arbor wrenches (both of them) and an allen wrench for adjusting the riving knife and dust ejection points among other things. Our favorite was the rip fence, which simply flipped upside down and stored underneath the table – clever! About the most difficult adjustment was the riving knife, which is a tool-less maneuver, but one which requires you to stick your hand way into the blade cavity to reach the release lever. When making any adjustments to the blade, it goes without saying (but we’ll say it anyway) to disconnect power to the saw as a precaution.
×